• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.212-214
• /
• 2004

Hardware implemented ring buffer systems and methods are presented for the effective management of the ring buffer in TCP/IP communication. The layer interface of the ring buffer systems transfer free buffer and used buffer size information to the TCP/IP stack upper or low layer. The pointer updation interface calculates a temporary pointer from the data size which is needed by the present pointer of the ring buffer and upper or lowyer layer. The pointer manager of the ring buffer systems is responsible for saving the present pointer of the ring buffer, updating the ring buffer pointer to the new pointer, calculating the free buffer size and used buffer size of the ring buffer, and transferring the information to the upper layer. The ring buffer systems help the TCP/IP layer and TCP/IP upper or lower layer to decide the sending or receiving data size effectively. The delay of transferring data can be lowered by the ring buffer system.

• Culinary science and hospitality research
• /
• v.13 no.2
• /
• pp.254-259
• /
• 2007

The control of enzymic browning in potato slices by the use of citrate and phosphate buffer at different pH values and concentration was investigated. Minimally processed potatoes were stored at $5^{\circ}C$ and $20^{\circ}C$ followed by dipping in distilled water, citrate buffer (pH $3.0{\sim}5.0$) and phosphate buffer (pH $5.0{\sim}7.0$). The color characteristic was measured after storage at $5^{\circ}C$ and $20^{\circ}C$ for 24 hours. Treatment effectiveness was greatly improved by reducing pH and temperature. The citrate buffer was more effective than phosphate buffer in the browning inhibitory capacity. The citrate buffer (pH 3.0) showed the most anti-browning effect in this condition and more effective inhibition of browning by increasing concentration of treatment solution. The phosphate buffer (pH 5.0) treatment showed more effectiveness than concentration of 0.5 M of citrate buffer treatment.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.41 no.5
• /
• pp.9-16
• /
• 2004

The data link layer of the PCI Express must have the transmitting buffer that contains the packets to transmit next time. Also it must have the retry buffer that contains the packets which were already transmitted but have not been acknowledged by the corresponding target device. In the separated buffer architecture, the data link layer can not transmit the packets in the transmitting buffer if the reiry buffer space is not enough. In this paper, we propose an efficient buffer architecture which merges the transmitting buffer and the retry buffer to a single buffer. Since the proposed buffer can dynamically assign the size of the transmitting buffer and the retry buffer, it can improve the buffer usage efficiency and the data transfer efficiency. The simulation result shows that the proposed buffer has the higher data transfer efficiency than the separated buffer architecture about 39% when the total buffer size is 8K byte.

• Proceedings of the IEEK Conference
• /
• 2003.11b
• /
• pp.69-72
• /
• 2003

The PCI Express spec introduces retry buffer in Data Link Layer For data integrity. But this buffer have some restrictions as buffer's usage. So we proposed effective management for retry buffer on PCI-Express interface. Proposed buffer management give increase performance and data integrity simultaneously.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.8
• /
• pp.3542-3566
• /
• 2018

In this paper, we investigate a buffer-aided wireless powered cooperative communication network (WPCCN), in which the source and relay harvest the energy from a dedicated power beacon via wireless energy transfer, then the source transmits the data to the destination through the relay. Both the source and relay are equipped with an energy buffer to store the harvested energy in the energy transfer stage. In addition, the relay is equipped with a data buffer and can temporarily store the received information. Considering the buffer-aided WPCCN, we propose two buffer-aided relaying protocols, which named as the buffer-aided harvest-then-transmit (HtT) protocol and the buffer-aided joint mode selection and power allocation (JMSPA) protocol, respectively. For the buffer-aided HtT protocol, the time-averaged achievable rate is obtained in closed form. For the buffer-aided JMSPA protocol, the optimal adaptive mode selection scheme and power allocation scheme, which jointly maximize the time-averaged throughput of system, are obtained by employing the Lyapunov optimization theory. Furthermore, we drive the theoretical bounds on the time-averaged achievable rate and time-averaged delay, then present the throughput-delay tradeoff achieved by the joint JMSPA protocol. Simulation results validate the throughput performance gain of the proposed buffer-aided relaying protocols and verify the theoretical analysis.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.787-790
• /
• 2012

The objective of this research is to design a high-performance NAND flash memory system containing a buffer system. The proposed instruction buffer in the NAND flash memory consists of two parts, that is, a fully associative temporal buffer for temporal locality and a fully associative spatial buffer for spatial locality. A spatial buffer with a large fetching size turns out to be effective for serial instructions, and a temporal buffer with a small fetching size is devised for branch instructions. Simulation shows that the average memory access time of the proposed system is better than that of other buffer systems with four times more space. The average miss ratio is improved by about 70% compared with that of other buffer systems.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.7
• /
• pp.1-8
• /
• 2019

Recently, an SSD with hybrid buffer memories is actively researching to reduce the overall latency in server computing systems. However, existing hybrid buffer policies caused many swapping operations in pages because it did not consider the overall latency such as read/write operations of flash chips in the SSD. This paper proposes the clock with hybrid buffer memories (CLOCK-HBM) for a new hybrid buffer policy in the SSD with server computing systems. The CLOCK-HBM constructs new policies based on unique characteristics in both DRAM buffer and NVMs buffer for reducing the number of swapping operations in the SSD. In experimental results, the CLOCK-HBM reduced the number of swapping operations in the SSD by 43.5% on average, compared with LRU, CLOCK, and CLOCK-DNV.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.147-147
• /
• 2015

The multilayer structure of the organic light emitting diode has merits of improving interfacial characteristics and helping carriers inject into emission layer and transport easier. There are many reports to control hole injection from anode electrode by using transition metal oxide as an anode buffer layer, such as V2O5, MoO3, NiO, and Fe3O4. In this study, we apply thin films of LiF which is usually inserted as a thin buffer layer between electron transport layer(ETL) and cathode, as an anode buffer layer to reduce the hole injection barrier height from ITO. The thickness of LiF as an anode buffer layer is tested from 0 nm to 1.0 nm. As shown in the figure 1 and 2, the luminous efficiency versus current density is improved by LiF anode buffer layer, and the threshold voltage is reduced when LiF buffer layer is increased up to 0.6 nm then the device does not work when LiF thickness is close to 1.0 nm As a result, we can confirm that the thin layer of LiF, about 0.6 nm, as an anode buffer reduces the hole injection barrier height from ITO, and this results the improved luminous efficiency. This study shows that LiF can be used as an anode buffer layer for improved hole injection as well as cathode buffer layer.

• Journal of Communications and Networks
• /
• v.16 no.6
• /
• pp.656-666
• /
• 2014

In delay tolerant networks (DTNs), delay is inevitable; thus, making better use of buffer space to maximize the packet delivery rate is more important than delay reduction. In DTNs, epidemic routing is a well-known routing protocol. However, epidemic routing is very sensitive to buffer size. Once the buffer size in nodes is insufficient, the performance of epidemic routing will be drastically reduced. In this paper, we propose a buffer scheme to optimize the performance of epidemic routing on the basis of the Lagrangian and dual problem models. By using the proposed optimal buffer scheme, the packet delivery rate in epidemic routing is considerably improved. Our simulation results show that epidemic routing with the proposed optimal buffer scheme outperforms the original epidemic routing in terms of packet delivery rate and average end-to-end delay. It is worth noting that the improved epidemic routing needs much less buffer size compared to that of the original epidemic routing for ensuring the same packet delivery rate. In particular, even though the buffer size is very small (e.g., 50), the packet delivery rate in epidemic routing with the proposed optimal buffer scheme is still 95.8%, which can satisfy general communication demand.

• Korean Journal of Materials Research
• /
• v.27 no.8
• /
• pp.403-408
• /
• 2017

We investigated the effect of ZnO buffer layer on the formation of ZnO thin film by ultrasonic assisted spray pyrolysis deposition. ZnO buffer layer was formed by wet solution method, which was repeated several times. Structural and optical properties of the ZnO thin films deposited on the ZnO buffer layers with various cycles and at various temperatures were investigated by field-emission scanning electron microscopy, X-ray diffraction, and photoluminescence spectrum analysis. The structural investigations showed that three-dimensional island shaped ZnO was formed on the bare Si substrate without buffer layers, while two-dimensional ZnO thin film was deposited on the ZnO buffer layers. In addition, structural and optical investigations showed that the crystalline quality of ZnO thin film was improved by introducing the buffer layers. This improvement was attributed to the modulation of the surface energy of the Si surface by the ZnO buffer layer, which finally resulted in a modification of the growth mode from three to two-dimensional.