• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.6
• /
• pp.361-367
• /
• 1988

In this study new design method with auxiliary slot on salient pole is proposed for the reduction of cogging torque which is the problem of corm type DC Brushless motor. And FEM(Finite element method) is adapted in trial motor which is designed by the method proposed in this paper. and learn the quantative characteristics of cogging torque. Comparing results of analysis with measurement it is porved that the proposed design has a propriety.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.4
• /
• pp.98-107
• /
• 2005

Brushless DC motor(BLDCM) can be driven by 120[^{\circ}]$ square wave voltage and use PWM pulse patterns in two-phase feeding scheme to control the speed of the motor. This Paper introduces four PWM modes used BLDCM control system, and analyzes their different influences on the motor performances using a time-stepped voltage source finite element method. To verify the proposed computational method, we built the prototype motor for electrical power steering(EPS) and compared the predicted and the measured back EMF and phase current.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.1925-1933
• /
• 2017

The brushless DC motor's commutation torque ripple is caused by inconsistency in the rate of phase current change. Thus, a method that considers armature resistance is proposed to modulate phase current. The three-phase control strategy, which involves the "open-phase conduction, off-phase pulse width modulation, and maintained non-commutation phase" technique, is applied during commutation at full-speed segments of the motor. Changes in each phase current are analyzed theoretically by establishing mathematical model based on phase current to determine the relative difference among shutdown phase, duty, and motor operating parameters. The turn-on and turn-off phase current change rates are made to be consistent to ensure less non-commutation phase current ripple, then the torque ripple is inhibited. The simulation results show that the phase commutation current and torque ripple coefficient of the proposed method are reduced from 56.9% and 55.5% to 6.8% and 6.1%, respectively. In the experiment system, the pulsation coefficient of the motor phase current is reduced from 40.0% to 16.7% at low speed and 50.0% to 18.8% at high speed. The simulation and experimental results show that the proposed control method significantly inhibits commutation current and torque in the full section.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.2
• /
• pp.295-303
• /
• 2013

This paper reports an investigation of pulse width modulation (PWM) techniques for two-phase brushless DC (BLDC) motors fed by a two-phase eight-switch inverter in a fan application. The three-phase BLDC motor is widely applied in industry; however, a lower-cost two-phase BLDC motor and drive circuit has been greatly in demand in recent years. In this paper, we introduce a mathematical model of the two-phase BLDC motor with sinusoidal back electromotive forces (EMFs) based on traditional three-phase BLDC motors. To simplify the drive algorithm and speed up its application, we analyze the principle of block commutation for a two-phase BLDC motor drive in the 180-electrical-degree conduction mode, and we further propose five PWM schemes to improve the commutation performance of the two-phase BLDC drive. The effectiveness of the proposed PWM methods is verified through experiments.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.200-204
• /
• 1998

In this paper, a mathematical model of Brushless DC machine fed by pwm inverter is developed. Dynamic and steady state characteristics of Brushless DC motor is simulated and analyzed: electromagnetic torque, speed, phase voltage, and current. In mathematical modeling, the shaft transformation referencing rotor frame from to "a,b,c" three phase frame to "d,g" two phase frame is described.

• Journal of Magnetics
• /
• v.15 no.1
• /
• pp.40-44
• /
• 2010

This paper introduces two types of magnetization, and reports the effect of the magnetization direction on the iron loss in a brushless DC (BLDC) motor using a 2-D time-stepped voltage source finite-element method (FEM). The iron losses were found to consist of hysteresis and eddy current loss, which were calculated from the time variation of the magnetic field distribution. To confirm the analysis, a prototype BLDC motor was constructed with a sintered ferrite magnet. The analysis and experimental results suggest that the magnetization direction has a significant effect in terms of the iron loss characteristics of the BLDC motor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.491-497
• /
• 2004

This paper presents a new rotor position estimation method for brushless DC motors. It is clear that the estimation error of the rotor position provokes the phase shift angle misaligned between the phase current and the back-EMF waveforms, which causes torque ripple in brushless DC motor drives. Such an estimation error can be reduced with the help of the proposed neutral voltage-based estimation method that is structured in the form of a closed loop observer. A neutral voltage appearing during the normal mode of the inverter operation is found to be an observable and controllable measure, which can be dealt with for estimating an exact rotor position. This neutral voltage is obtained from the DC-link current, the switching logic, and the motor speed values. The proposed algorithm, which can be implemented easily by using a single DC-link current and the motor terminal voltage sensors, is verified by simulation and experiment results.

• Journal of Power Electronics
• /
• v.11 no.2
• /
• pp.173-178
• /
• 2011

In order to verify the performance of brushless DC (BLDC) motors, the simulation method has been widely used. The current of a BLDC motors flows on two phase windings to obtain a constant torque. However, the freewheeling current caused by the inductance component of a BLDC motor exists at the commutation point so that the current can flow on three phase windings at the same time. Due to the changes of the excited phases, the model equations are frequently changed during BLDC motor drive operation. The model equations can be also changed by the applied switching pattern since the current path in the inverter circuit changes according to switching pattern. A BLDC motor system can utilize various switching patterns for many different purposes. However, such changes of the model equations complicate the simulation procedure. In this paper, the technique to set up model equations is proposed to ease the simulation of a BLDC motor system through an inverter circuit analysis. The proposed technique will be verified using the C language. Although this method does not provide the level of detail obtainable from commercial simulation tools like PSIM or SIMULINK, it can provide an efficient way to quickly compare various conditions.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.1
• /
• pp.1-9
• /
• 2001

In this paper, the general research on the analysis of the vibration due to magnetic exciting force in the small brushless DC(BLDC) motor, which is used in the Digital Versatile Disk(DVD) ROM driving system, is performed. The first part of the study is the analysis of the magnetic exciting force in the air gap region. As a verification of the exciting force by numerical analysis, the magnetic exciting force distribution in the air gap region is computed by using Reluctance Network Method(RNM). In addition, the effect of the eccentricity on the magnetic exciting force is discussed. The other part of the research is the structural analysis of the rotor structure of the BLDC motor. The matural mode analysis of the rotor structure is performed, and the vibration response due to magnetic exciting force is found. As a result of the procedures, the basic estimation of the effect of the magnetic exciting force on the vibration of BLDC motor is suggested.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.170-172
• /
• 2003

Among low power servo applications, classical DC motors are very popular because they are reasonably cheap and easy to control. The main disadvantage is the mechanical collector which has only a limited life period. Also, brush sparking can destroy the rotor coil, generate EMC problems. So permanent magnet brushless do motors and drives are being used increasingly in a wide range of applications. This has been made possible with the advantages of high performance permanent magnets with high coercively and residual magnetic, which make it possible for the PM to have superior power density, torque to inertia ratio and efficiency, when compared to an induction or conventional dc machine. This paper presents the design of a PM brushless dc motor drive simplistically operates as a classical dc motor. The BLDC motor drive system for this paper composes to the power integrated circuits, the one chip device. And several simple semiconductors add to drive system for a motor drive system simplistically operates as a conventional dc motor. Test results confirmed the feasibility of the proposed motor drive system design.