• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 D
• /
• pp.647-649
• /
• 2000

Brushless DC motors are widely used in many industrial fields as an actuator of robot and driving power motors of electrical vehicle. In this paper adaptive fuzzy sliding mode scheme is developed for velocity control of brushless DC motor. The proposed scheme does not require an accurate dynamic model. yet it guarantees asymptotic trajectory tracking despite torque variations. Numerical simulation and DSP-based experimental works for velocity control of brushless DC motor are carried out.

• 대한기계학회논문집B
• /
• 제32권2호
• /
• pp.141-148
• /
• 2008

A numerical simulation of brushless DC motor is performed to elucidate thermo-flow characteristics in winding and bearing with heat generation. Rotation of rotor and blades drives influx of ambient air into the rotor inlet. Recirculation zone exists in the tiny interfaces between windings. The flow separation causes poor cooling performance in bearing part and therefore the redesign of the bearing groove is required. The design parameters such as the inlet location, geometry and bearing groove threshold angle have been selected in the present simulation. As the inlet location moves inward in the radial direction, total incoming flow rate and heat transfer rate are increased. Total incoming flow rate is increased with increasing the inlet inner length. The effect of the bearing groove threshold angle on the thermal performance is less than that of other design parameters.

• 조명전기설비학회논문지
• /
• 제16권5호
• /
• pp.45-52
• /
• 2002

본 논문에서는 데이터 수집 보드로부터 호스트 컴퓨터로 시리얼 통신 채널을 통하여 전송된 BLDC(Brushless DC)모터의 입력과 출력 정보를 이용하여 모터의 저항값을 추정함으로써 고장을 검출하는 고장검출 시스템을 제안하였다. 프레임 크기가 고정된 프로토콜을 설계하고, 주기적으로 통신이 이루어지도록 하여 시리얼 통신 채널에서 발생되는 대역폭 제한으로 인한 시간지연문제를 해결하였으며, 저항값을 추정하기 위하여 간략화된 BLDC모터 모델과 순환형 최소자승법 알고리즘을 사용하였다. 제안된 고장 검출 방법은 실험을 통하여 성능을 확인하였다.

• 반도체디스플레이기술학회지
• /
• 제23권1호
• /
• pp.48-51
• /
• 2024

Recently, high-performance BLDC(Brushless DC) motors are being applied to various fields such as industrial and personal mobility devices and drones. To achieve the best performance of BLDC, sensors such as hall sensors, encoders, and resolvers are used to determine the position of the rotor, and various speed control technologies are being developed. However, due to problems with high-speed control due to external environmental factors and frequency bandwidth of semiconductor sensing devices, research on BLDC motors without semiconductor sensing devices is in progress. Therefore, in this study, a signal brush was added to the end of the rotor of a BLDC motor and the rotor position of the BLDC motor was detected by analyzing the signal output through the signal brush.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.200-204
• /
• 1998

In this paper, a mathematical model of Brushless DC machine fed by pwm inverter is developed. Dynamic and steady state characteristics of Brushless DC motor is simulated and analyzed: electromagnetic torque, speed, phase voltage, and current. In mathematical modeling, the shaft transformation referencing rotor frame from to "a,b,c" three phase frame to "d,g" two phase frame is described.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.675-677
• /
• 2000

In the paper the eddy current loss in brushless DC motor due to switching frequency supplied by PWM inverter, is analyzed. The compensated conductivity is used in order to analyze the eddy current loss in brushless DC motor which has lamination structure. The eddy current loss is deceased when switching frequency supplied by PWM inverter is gradually increased from 1.2kHz up to 12kHz. The high switching frequency of PWM inverter make the output wave into a similar sine wave and this leads to the decreasing eddy current loss.

• 대한전기학회논문지
• /
• 제37권6호
• /
• pp.361-367
• /
• 1988

In this study new design method with auxiliary slot on salient pole is proposed for the reduction of cogging torque which is the problem of corm type DC Brushless motor. And FEM(Finite element method) is adapted in trial motor which is designed by the method proposed in this paper. and learn the quantative characteristics of cogging torque. Comparing results of analysis with measurement it is porved that the proposed design has a propriety.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 D
• /
• pp.2399-2401
• /
• 2001

This Paper presents a positioning control method of the LBLDCM(Linear Brushless DC Motor) under friction. The friction may cause steady state position error. So it is necessary to consider friction effect for precision positioning control. The proposed control method uses disturbance observer algorithm and friction compensation. The experimental results of the proposed control method based on the disturbance observer are presented to show its effectiveness.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1138-1142
• /
• 2007

As a brush DC motor, the brushless DC motor is also operated by DC power supply but has no mechanical contacts occurred by a brush or a commutator. Though the performance of BLDC motor is almost similar with that of DC motor, the BLDC motor has the advantage of the high speed responsibility, the high controllability, and the high effectiveness. The control valve using the BLDC motor, which excludes the burnout effect provoked possibly by the vacuum condition during the flight, is employed for the upper stage of a launch vehicle. For the component level analysis, the dynamic response characteristics of BLDC and DC motors to the same design input sources have been studied in using AMEsim.

• 한국전자통신학회논문지
• /
• 제9권1호
• /
• pp.83-90
• /
• 2014

본 논문에서는 BLDC 모터로 구동되는 오일 펌프 제어 시스템을 설계하고 구현하는 문제를 다룬다. 제안된 오일 펌프는 하이브리드 차량에 장착되어 엔진 클러치와 변속기에 충분한 양의 작동유를 공급하는 역할을 한다. BLCD 모터로 구동되는 제어기를 단순화하여 전원 전압을 PWM 방식으로 직접 제어하는 일반적인 방법을 사용함으로써 응답성 및 정확성을 향상시키는 것을 주목적으로 한다. 제안된 제어 기법은 오일 펌프 장치의 효율성과 신뢰성을 높인다. BLCD 모터의 회전과 오일 펌프 가동 실험을 실시하여 제안된 기법의 성능을 검증한다.