• Proceedings of the Optical Society of Korea Conference
• /
• 2005.02a
• /
• pp.20-21
• /
• 2005

• Journal of Korean Institute of Industrial Engineers
• /
• v.25 no.2
• /
• pp.233-239
• /
• 1999

With the increase of Internet protocol (IP) packets the performance of routers became an important issue in internetworking. In this paper we examined the matching algorithm in gigabit router which has input queue with virtual output queueing. Port partitioning concept is employed to reduce the computational burden of the scheduler within a switch. The input and output ports are divided into two groups such that the matching algorithm is implemented within each input-output pair group in parallel. The matching is performed by exchanging input and output port groups at every time slot to handle all incoming traffics. Two algorithms, maximal weight matching by port partitioning (MPP) and modified maximal weight matching by port partitioning (MMPP) are presented. MMPP has the lowest delay for every packet arrival rate. The buffer size on a port is approximately 20-60 packets depending on the packet arrival rates. The throughput is illustrated to be linear to the packet arrival rate, which can be achieved under highly efficient matching algorithm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.768-775
• /
• 2005

In this paper, the broadband cross monopole antenna is presented and the radiation characteristics is investigated f3r various width and height of the radiated element. In the presented antenna, the broadband characteristics is realized by the cross monopole element and the impedance matching section between the element and the ground. To conform the broadband characteristics of the presented antenna, the experimental antenna is designed, fabricated, and its radiation characteristics are measured in $1.75\~2.655$ GHz. It is shown that the designed antenna has the nondirectional pattern in the horizontal plane, the directional pattern in the vertical plane, VSSR less than 1.5, and gain in $2.5\~3.78$ dBi. From these results, the presented antenna is conformed as a broadband indoor antenna which can be used for PCS, WCDMA, Wibro, and satellite DMB band.

• Journal of Sensor Science and Technology
• /
• v.25 no.1
• /
• pp.46-50
• /
• 2016

During KSTAR plasma experiments, torsional $Alfv\acute{e}n$ waves in the frequency of few GHz or below were detected. To understand this plasma waves during the crash of MHD instabilities, an RF spectrometer has been developed for detection of the radiated RF signals in the KSTAR Tokamak. It has the capability of broadband RF spectral measurement (50 ~ 400 MHz). To detect the broadband RF signals which are radiated from the KSTAR systems, a broadband antenna is the key feature of the RF spectrometer. In this paper, a broadband bowtie antenna for detection of $Alfv\acute{e}n$-waves in the KSTAR Tokamak is presented. Planar-type bowtie antenna is designed and fabricated on an FR4 substrate with thickness of 1.6 mm. The antenna consists of bowtie shaped balanced radiators and broadband planar balun. The antenna is designed to have an input impedance of 50 Ohm, and a taper-shaped balun is adopted for field and impedance matching between 50 Ohm transmission line to 110 Ohm feeding network of balanced radiators. The implemented antenna provides around -3 to 3 dBi of gain for the whole frequency band. The VSWR of the bowtie antenna is less than 12:1 over the frequency bandwidth of 50 to 2000 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.1 s.92
• /
• pp.102-112
• /
• 2005

In this work, we developed fully integrated broadband MMIC chip set employing CSP(Chip Size Package) for K/Ka band applications. By utilizing an ACF for the RF-CSP, the fabrication process for the packaged amplifier MMIC could be simplified and made cost effective. $STO(SrTi_{3})$ capacitors were employed to integrate the DC biasing components on the MMIC, and LC parallel circuits were employed for DC feed and ESD protection. A pre-matching technique and RC parallel circuit were used to achieve a broadband matching and good stability fer the amplifier MMIC in K/Ka band. The amplifier CSP MMIC exhibited good RF performance over a wide frequency range in K/Ka band. This work is the first report of a fully integrated CSP amplifier MMIC successfully operating in the K/Ka band.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.467-474
• /
• 2019

In this paper, we studied a method for a broadband stacked patch antenna structure which is widely used for bandwidth improvement. The characteristics according to the distance between the two patches were analyzed and the impedance matching was optimized by connecting parallel open stubs to the main patch feed line. The shunt matching stub is inserted underneath the parasitic patch and so it does not require additional space, which enables the proposed antenna structure to be advantageous in miniaturizing antenna. The effects of the various parameters on the antenna performance are examined, and we introduced the design procedure for the proposed antenna to operate in the frequency range of 2.3~2.7GHz. Experimental results show that the bandwidth of the proposed antenna is about 480MHz with 2.27~2.75GHz bandwidth. And the antenna gain was 5.8dBi at 2.3GHz and 7.8dBi at 2.6GHz within the bandwidth.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.72-73
• /
• 2016

In this paper, we studied a method for miniaturizing a broadband stacked patch antenna structure which is widely used for bandwidth improvement. Main patch is a rectangular microstrip patch antenna fed by a 50-ohm microstrip line, and a parasitic patch is laid above the main patch. The size of the main patch is designed to be resonated near the center frequency of the desired frequency band. Then parasitic patch longer than main patch is placed above the main patch. The distance between two patches might be adjusted so as to achieve impedance matching using a shunt open stub. The shunt matching stub is inserted underneath the parasitic patch and so it does not require additional space, which enables the proposed antenna structure to be advantageous in miniaturizing antenna. The effects of the various parameters on the antenna performance are examined, and we introduced the design procedure for the proposed antenna to operate in the frequency range of 2.3-2.7 GHz.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.9
• /
• pp.755-759
• /
• 2013

A broad-band underwater acoustic transducer that uses thickness vibration mode, derived from a disk type piezoelectric ceramic, has been proposed and designed for DVL (Doppler Velocity Log). Three different types of acoustic transducer were evaluated with respect to the transmitting voltage response, receiving voltage sensitivity and bandwidth of the transducer. The effect of the acoustic impedance matching layer and backing layer is discussed. The results demonstrated that three matching layer with lossy backing layer is the best configuration for underwater transducer. The trial underwater acoustic transducer with three matching layer has a frequency bandwidth of 55%, maximum transmitting voltage response of 200 dB and a maximum receiving voltage sensitivity of -187.3 dB.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.6
• /
• pp.665-670
• /
• 2015

In this paper, We proposed a broadband RF amplifier for Microwave band receiver. We also proposed a broadband RF amplifier, designed by using EM simulation for reliable amplification of the received signal. Connected to a source terminal to via, it minimizes those which are the active elements of source-side oscillation as the operating element in an ideal GND, and a constant gain characteristic in a broadband. The goal of this was to obtain stable amplification characteristics. For implementing this architecture, we designed the broadband(500 MHz ~ 7 GHz) RF amplifier by using commercial GaAs FET, which operate on 720 MHz, 4,595 MHz, and 6,035 MHz by impedance matching. The voltage gain is 10.635 dB ~ 14.407 dB(737.5 MHz ~ 6.0575 GHz), P1dB is 20 dBc of band(1st harmonic/2nd harmonic).

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.59-60
• /
• 2017

In this paper, we studied a design method for obtaining broadband property by loading a chip capacitor on a coplanar waveguide(CPW)-fed compact quasi-Yagi antenna(QYA). The proposed antenna is a three-element QYA with dipole, reflector, and director. To reduce the size, the ends of both dipole and reflector are bent, and balun is incorporated in the antenna. To improve impedance matching, the loading position and capacitance value of chip capacitor were determined. From some simulations, the proposed antenna using an FR4 substrate with a size of 90 mm by 90 mm was designed for the operation in a broadband covering the UHF RFID and GPS systems. The antenna showed a good performance with a broadband of 850-1,626 MHz(62.7%) for a VSWR ${\leq}2$, a gain ${\geq}3dBi$, and a frong-to-back ratio ${\geq}4.6dB$.