• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.97-100
• /
• 2002

In this research, the impact behavior of the boundary between MMC-reinforced SiC whisker and Al alloy were studied. It is known that the resultant of the interfacial reaction between SiC whisker and Al alloy has brittle and low toughness property. In this paper, impact behavior of graded MMC & Al alloy shows the interfacial opening at the boundary. Generally this phenomenon is generated by thermal residual stress, brittle interfacial reaction resultant and difference of the deflection. So, these results may be interpreted as a macroscopic method of measuring the interfacial strength between matrix and reinforcement

• Magazine of the Korea Concrete Institute
• /
• v.7 no.3
• /
• pp.164-174
• /
• 1995

Reliability of RC beanls designed for flexure under the provisions of ACI Building Code is analyzed. The results are compared with those obtained previously. It is shown that in some cases the reliability is inadequate and changes substantiallv with reinforcernent ratio. The probability of brittle failure appears to be rather high. The reasons for these phenomena are revealed and some measures to remedy the situation are recommentied. hluch attention is given to the conditions askthey stand at present in Korea.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.2073-2080
• /
• 1994

In this paper, a model of material removal in abrasive water jet machining of brittle material is developed, and experimentally evaluated. Abrasive water jet machining proved to yield better material removal rate than other machining techniques for hard and brittle material (alumina ceramics). It was also found that large scale fracture may develop at the exit of the jet from the material. The fracture size was predicted as a function of water jet pressure and size of the hole. Finally, the feasibility of using acoustic emission signals for in-process monitoring of the abrasive water jet machining process is investigated.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2008.10a
• /
• pp.3-16
• /
• 2008

The underground construction and mining are facing many geomechanics challenges stemming from, geological complexities and stress-driven rock mass degradation processes. Brittle failing rock at depth poses unique problems as stress-driven failure processes often dominate the tunnel behaviour. Such failure processes can lead to shallow unravelling or strainbursting modes of instability that cause difficult conditions for tunnel contractors. This keynote address focuses on the challenge of anticipating the actual behaviour of brittle rocks in laboratory testing, for empirical rock mass strength estimation, and by back-analysis of field observations. This paper summarizes lessons learned during the construction of deep Alpine tunnels and highlights implications that are of practical importance with respect to constructability. It builds on a recent presentation made at the $1^{st}$ Southern Hemisphere International Rock Mechanics Symposium held in Perth, Australia, in September this year, and includes results from recent developments.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.938-942
• /
• 2002

This paper has studied to obtain the grinding characteristics and optimal grinding renditions of ceramic materials in the grinding with diamond wheel by the experimental plan method. The load on wheel by varying the feed rate was related with the surface roughness due to the minute destruction phenomenon of grains for the Si$_3$${N^4} and Zr{O_2}$. The depth of cut is related with the surface roughness because the grinding is carried out by grain shedding process due to the brittle fracture phenomenon for the ${Al_2}{O_3}$. The major factors affecting the surface roughness and the optimum grinding conditions were obtained with minimum experiments using the experimental plan method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.711-714
• /
• 2002

Although recent research of metallic materials in high temperature fatigue have been much accomplished, many studies about brittle material as a die steel in high temperature fatigue does not have been reported. Especially, the study on the fatigue behavior over the transformation temperature is not studied sufficiently because of its difficult analysis and experiment. Therefore, reliable results of brittle material in high temperature fatigue behavior are needed. In this paper, stress-strain curves and stress-life curves in die STD61 steel at 700 and 900 are carefully examined, as the basic experimental data are used to predict from fatigue life over 700.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.1
• /
• pp.61-70
• /
• 2004

Generally, ceramics are very difficult-to-cut materials because of its high strength and hardness. The machining process of ceramics can be characterized by cracking and brittle fracture. In the machining of ceramics, edge chipping and crack propagation are the principal reasons to cause surface integrity deterioration. Such phenomenon can cause not only poor dimensional and geometric accuracy, but also possible failure of the ceramic parts. Ceramics can be machined with traditional method such as grinding and polishing. However, such processes are generally cost-expensive and have low material removal rate. Thus, in this paper, to overcome these problems. BN powder, which gives good cutting property, is added for the fabrication of machinable ceramics by volume of 5,10,15,20,25 and 30%. And, mechanical properties, R-curve behavior and machining tests are carried out to evaluate the machining properties of the manufactured machinable ceramics.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.04a
• /
• pp.96-101
• /
• 1997

In recent years, grinding techniques for precision machining of brittle materials used in electric, optical and magnetic parts have been improved by using superabrasive wheel and precision grinding machine. The present dressing system cannot have controll of optimum dressing of the superabrasive wheel. In this study, a new system and the grinding mechanism of optimum in-process electrolytic dressing were proposed. This system can carry out optimum in-process dressing of superabrasive wheel, and give very effective control according to unstable current and gap increase. Therefore, the optimum in-process electrolytic dressing is a good method to obtain the efficiency and mirror-like grinding of brittle materials.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.1 s.94
• /
• pp.18-25
• /
• 1999

Chipping is an unavoidable phenomenon in the slot grinding process of hard and brittle materials. However, it should be reduced for the improvement of surface integrity in the manufacture of optical and semiconductor components. Electrolytic In-process Dressing (ELID) technique for metal bonded superabrasive grinding wheel has been developed for mirror surface grinding of hard and brittle materials. Electrically dressed wheel surface has sharply exposed abrasives and results in lower grinding force, higher grinding efficiency in grinding. The paper deals with a newly developed method for slot grinding using ELID and was implemented to improve grooved surface quality and decreases chipping size on the edge of the groove. As a result, we accomplished chipping-free grooves and obtained the clear ground surfaces on glass and WC.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.5
• /
• pp.97-103
• /
• 2006

A meso-scale analysis method using the natural element method, which is a kind of meshless method, is proposed for the analysis of material damage of brittle microcracking solids such as ceramic materials, concrete and rocks. The microcracking is assumed to occur along Voronoi edges in the Voronoi diagram generated using the nodal points as the generators. The mechanical effect of microcracks is considered by controlling the material constants in the neighborhood of the microcracks. The macro elastic moduli of anisotropic as well as isotropic solids containing a number of randomly distributed microcracks are calculated in order to demonstrate the validity of the proposed method.