• Korean Journal of Materials Research
• /
• v.13 no.7
• /
• pp.424-428
• /
• 2003

The microstructure and field emission properties of carbon nanotubes(CNT) grown by Ni-catalytic chemical vapor deposition(CVD) were investigated. CVD-grown CNT had a high density of curved shape with randomly oriented. It was found that an increase in electric field caused an increase in field emission current and field emission sites of CNT. The maximum field emission current density was measured to be 3.6 ㎃/$\textrm{cm}^2$ at 2.5 V/$\mu\textrm{m}$, while the brightness of 56 cd/$\textrm{cm}^2$ was observed for the CNT-grown area of 0.8 $\textrm{cm}^2$ from a phosphor screen. Field emission current at constant electric field gradually decreased initially and then stabilized with time.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.120-125
• /
• 2002

AC powder EL devices were fabricated by screen printing method with the dielectric materials in insulating layer and the electrical resistivity of rear electrode. Brightness and current density were measured at voltage range of 50∼300 $V_{rms}$ to estimate optoelectrical properties of AC powder EL devices, respectively. Frequency generator was used as system producing frequency and voltage of a sine wave. Brightness and current density were measured by luminometer and multimeter. Also, dielectric constant for dielectric layer was measured by impedance analyser after preparing thick film. Dielectric constant was improved with amount of $TiO_2$ to $BaTiO_3$ powder. By applying such a process to dielectric layer of low cost AC powder EL device, brightness was improved to 50 cd/$m^2$ at similar current density. Dielectric constant $BaTiO_3$ powder by solution combustion process is better than commercial $BaTiO_3$ powder. By applying to that of low power consumption AC powder EL device, brightness was improved to 85 cd/$m^2$. Brightness of AC powder EL device was relatively decreased by control of electrical resistivity of rear electrode, current density was also decreased.

• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1085-1092
• /
• 2001

The high efficient AC powder EL devices classified by low cost and low power consumption type fabricated using screen printing method with film thickness and organic binder. Brightness and current density were measured at frequency range of 400Hz∼1kHz and voltage range of 50∼300V$\_$rms/ to estimate optoelectrical properties of AC powder EL devices, respectively. Frequency generator was used as system producing frequency and voltage of a sine wave. Also brightness and current density were measured by luminometer and multimeter. In the case of low cost type AC powder EL device, brightness and current density were about 43 cd/m$^2$and 20$\mu$A/cm$^2$when the thickness of phosphor and dielectric layer was 45∼50$\mu$m under no addition of plasticizer respectively. In the case of low power consumption type AC powder EL device, brightness and current density were about 74 cd/m$^2$and 30∼40$\mu$A/cm$^2$when the thickness of phosphor and dielectric layer was 45∼50$\mu$m and 15∼20$\mu$m under addition of 15wt% plasticizer respectively. Also, AC powder EL device fabricated in this study showed absolutely excellent characteristics as the lifetime was longer than products of other company.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.268-269
• /
• 2006

The estimation of applicability $SrTiO_3:Pr^{3+}$, Al to a class low-voltage flat-panel displays based on field emission effect, which have average value anode voltage $U_a=300V$ and current density $j=100\;mA/sm^2$ at duty 240, has given positive result. In the same time observably for the most effective sample in similar conditions of excitation high brightness - more than $500\;Kd/m^2$ and linear brightness dependences from current density and voltage allows to decrease greatly the power which consumed by the device.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.618-625
• /
• 2005

This paper has achieved that an optimal design and experiments of heater and cathode of electron gun that serve to embody high current density in CRT display. For the high brightness, high resolution and larger size in CRT display, high current density of electron gun is indispensible. An Impregnation style cathode is used, and must heighten operating temperature of heater to get high current density for this, it is proportional hereupon and power dissipation increases. In this paper, to get low power cathode with high current density, There are produced and tested sample that differ lead type of heater, coating method, the pitch and number of winding of the first and second coiling in the heat emission area for the low power design of high current density cathode heater in this paper.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.9
• /
• pp.696-700
• /
• 2010

We fabricated red and blue organic light emitting display (OLEDs) which had the two kinds of multi-structure of ITO/HIL/HTL/EML/ETL/LiF/Al and ITO/HIL/HTL/EML/ETL/LiF/Al/LiF. In the case of red OLED that had LiF/Al/LiF structure compared to LiF/Al structure, the current density increased from 4.3 mA/$cm^2$ to 7.3 mA/$cm^2$, and the brightness increased from 488 cd/$m^2$ to 1,023 cd/$m^2$ at 7.0 V, and as a result the current efficiency was improved from 11.28 cd/A to 13.95 cd/A. Also in the case of blue OLED that had LiF on Al cathode layer, the current density increased from 1.2 mA/$cm^2$ to 1.8 mA/$cm^2$, and the brightness increased from 45 cd/$m^2$ to 85 cd/$m^2$ at 7.0 V, and as a result the current efficiency was improved from 3.69 cd/A to 4.82 cd/A. Through these experimental results it could be suggested that the LiF layer formed on Al prevents the oxidation of Al surface, and the electrode resistance become low with increase of supplied electrons, therefore the brightness and the efficiency are improved from the influence to the well-balanced bonding of electron and hole at emitting layer.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.1
• /
• pp.40-48
• /
• 2004

Hardness and internal stress are very important in nickel electroforming. Nickel sulfamate bath has been widely used in electroforming because of its low internal stress and moderate hardness. Nickel sulfamate bath without chloride was chosen to investigated the effect of plating variable such as temperature, PH, current density and sodium naphthalene trisulfonate as addition agent on the hardness and internal stress. It was found that hardness increased with increasing temperature and decreasing current density and ranged from 150∼310 DPH. The hardness was highest at $55^{\circ}C$ and 10∼40 mA/$\textrm{cm}^2$. The internal stress increased with increasing current density and decreasing temperature. It was minimum at PH 3.0∼3.8. Low internal stress within $\pm$1,500 psi was obtained at both $50^{\circ}C$ and $55^{\circ}C$ in 10-20 mA/$\textrm{cm}^2$. The addition of sodium naphthalene trisulfonate was found to be effective in refine columnar grains thus resulted in decreasing internal stress, increasing hardness and improving brightness.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.2
• /
• pp.334-343
• /
• 1997

Reference white in color television receiver can be achieved by adjusting the RGB gun current ratio and it is necessary to provide additional gain ratio adjustment for the RGB video signal. Generally, the gun current density profile has a gaussian distribution and the gain-bandwidth product of RGB channel amplifieris constant. Therefore brightness and spatial resolution are changed with variations in reference white of receiver. In this paper, the effect of RGB gun current and channel gain ratios on brightness and resolution of CPT is analyzed. Brightness is increased with the color temperature of referenc white because of Helmholtz-kohlrausch effect. The change in ligh output is more abrupt and spatial resolution is improved with unity current ratio. For more bright and improved ressolution we also present the range of color temperature of reference white for P22 phosphors.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.61-64
• /
• 2015

The brightness of Io's magnetic footprint, an indicator of electromagnetic interaction at the satellite, appears to be strongly connected to the satellite's distance from the plasma equator. As a result, the brightest footprints were detected when Io is near the interception location between the satellite's orbital plane and the plasma equator. However, volcanic activities on Io show strong correlation with the equatorward shift of Jupiter's main auroral oval, consequently causing the disappearance of Io's footprint. The same conclusion was suggested via the observation of Jupiter's hectometric radio emission, called HOM, which closely corresponds to Jupiter's auroral activity. The plasma environment near the Jovian satellites was found to vary significantly at different observational epochs. The electron density increased by approximately a factor of three from the Voyager epoch (1979) to the Galileo epoch (1995), while the electron density was found to be significantly higher (~ 5 times) in the Cassini epoch (2001). In this current study, the magnetic footprints were clearly brighter ten years ago (from peak brightness in 1998-2001) than the footprints detected in 2007. For volcanic activities on Io in 2007, there are two clear activities in February and late May. The magnetic footprint appeared to be dimmer in March 2007, expected to be the result of volcano activities in Feb 2007. However, the magnetic footprint brightness in June appeared to be slightly brighter than the footprints observed in May. The reason could be the time delay between the brightening of the sodium nebula on approximately May 31st and, a while later, the enhancement of flux tube content peaking on approximately June 5th. On the other hand, Io's magnetic footprints were observed during June 1st - 10th when they may not yet have been affected by the increase in mass outflow due to the increase of plasma density.

• Journal of the Korean institute of surface engineering
• /
• v.14 no.4
• /
• pp.215-220
• /
• 1981

The surface appearance of chromium electrodeposit was studied by employing a pulse curr-ent plating in self-regulating high speed (SRHS) bath containing 20 g/$\ell$, K2SiF6 7.5 g/$\ell$ SrSO4 and 250 g/$\ell$ CrO3. As the pulse frequency increased, the surface appearance changed suddenly from bright a-ppearance in a direct current plating condition to gray one in the range of pulse frequency less than about 20KHz. However the bright appearance is recovered as the pulse frequen-cy exceeded 20 KHz. This phenomena seemed to be related with the preferred orientation of electrodeposits, considering the relationship between the preferred orientation of elect-rodeposits and surface appearance in a SRHS bath. Direct current plating was also applied to both Sargent and SRHS bath and investigat-ion on surface appearance was extended to the high current density of 400 A/dm2. In a Sa-rgent bath, the increase in bath temperature was necessary for bright appearance as the current density was increased within 150 A/dm2, but bright region was shown in the cons-tant temperature of 70-75$^{\circ}C$ above the current density of 150A/dm2. On the other hand, two regions of surface brightness was found in a SRHS bath. One is region in the low temperature less than 25$^{\circ}C$ and the other in the moderate temperature range from 55$^{\circ}C$ to 65$^{\circ}C$.