• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.931-943
• /
• 2018

Wireless power transfer (WPT) technology has been the focus of a lot of research due to its safety and convenience. The Z-source inverter (ZSI) was introduced into WPT systems to realize improved system performance. The ZSI regulates the dc-rail voltage in WPT systems without front-end converters and makes the inverter bridge immune to shoot-through states. However, when the WPT system is combined with a ZSI, the system parameters must be configured to prevent the ZSI from entering an "accidental shoot-through" (AST) state. This state can increase the THD and decrease system power and efficiency. This paper presents a mathematical analysis for the characteristics of a WPT system and a ZSI while addressing the causes of the AST state. To deal with this issue, the impact of the system parameters on the output are analyzed under two control algorithms and the primary compensation capacitance range is derived in detail. To validate the analysis, both simulations and experiments are carried out and the obtained results are presented.

• Restorative Dentistry and Endodontics
• /
• v.10 no.1
• /
• pp.31-42
• /
• 1984

The toxic effect of adhesive resins on the dog's pulp tissue was studied with 70 teeth from 5 dogs. The experimental materials were Clearfil, a mixture of Clearfil with calcium hydroxide powder, Panavia-EX, and a mixture of Panavia-EX with calcium hydroxide powder. As a control group, calcium hydroxide powder was used. Each material was placed on the pulpotomized tissue surface. After 3 days, 1, 2,4, and 6 weeks, the teeth and apical tissue were processed routinly and stained with hematoxylin and eosin. Pathological tissue changes due to the toxicity of adhesive resins were observed by light microscope, and the pH of Panavia-EX and the Bonding agent of Clearfil were measured. Following were the results; 1. In the group of calcium hydroxide powder, slight inflammatory change was observed in the pulpotomized surface and adjacent pulp tissue on 3 day. 1 week case showed incomplete dentin bridge. The remaining pulp tissue was normalized according to the days elapsed. 2. In the group of Clearfil, early inflammatory change revealed in the superificial portion of the remaining pulp tissue on 3 day. The inflammation spreaded over the total pulp tissue and partial necrosis was observed in 1 week and 2 week cases. Total necrosis of pulp tissue and moderate inflammatory change at the apical tissue was noticed in 4 week and 6 week cases. 3. In the group of Panavia-EX, moderate inflammatory change appeared in the superficial pulp tissue on 3 day, and severe inflammatory change over all pulp tissue found in 1 week case. Pulp necrosis was obvious in 2 week case. 4 week and 6 week cases were totally necrotized up to the periapical tissue. 4. In the groups of mixtures with calcium hydroxide powder, the pulp tissue destruction was retarded, compared with the groups of Clearfil and Panavia-EX. 5. Panavia-EX was more destructive than Clearfil. 6. The acidity of freshly mixed Bonding agent of Cleafil was pH 4.0, and that of Panavia-EX was pH 2.0.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.504-511
• /
• 2003

In this paper, inverter type neon power supply using a piezoelectric transformer is fabricated and its characteristic is investigated. Developed neon power supply is composed of basic circuit and blocks, such as rectifier part, frequency oscillation part and piezoelectric transformer and resonant half bridge inverters. In this paper for complement the low power limitation, piezoelectric transformer at parallel connected driving by inverter is studied for noon tubes system of high power. When piezoelectric transformer is connected with parallel, LC filter connection method with parallel and selection of inductance L and capacitor C of primary side is suggested for reduce unbalanced current at the terminal of each transformer. Piezoelectric transformers use piezoelectric ceramic devices. Thus it is wireless therefore it has high power density, high Isolation level, low loss, more light, and miniaturization. In addition, high voltage transfer ratio is expected because there is no leakage inductance. Also, it has economic merit that the electrical loss Is low because structure is simple, small and tighter weight.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.3
• /
• pp.211-219
• /
• 2014

This paper proposes a low voltage high current LLC resonant converter for Green PC. Green PC is composed of a lot of blade PCs, and it is a centralized system to manage them in computer center. Green PC should require that its power supplies have several characteristics such as low output voltage, high output current, and high power conversion efficiency. Conventional PSFB (Phase Shift Full Bridge) converter is usually used as DC/DC converter for computer power supply because it has high power conversion efficiency thanks to ZVS (Zero Voltage Switching) operation under middle and high load conditions. However, this converter has some problems such as large switching noise and limitation of ZVS operation under light load condition. In order to improve the performance of power supply for Green PC, a new power supply using popular high efficiency LLC resonant converter for low voltage and high current application is proposed in this paper. The proposed power supply has ZVS capability over the entire load range, thus resulting in good efficiency and high switching frequency. Experimental results verify the performance of the proposed power supply for Green PC using 2[kW] (19[V], 105[A]) rated prototype converter.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.128-128
• /
• 2000

박막의 탄성 특성을 평가하는 방법으로 nano-indentation, Brillouin light scattering measurement, ultrasonic surface wave measurement, bulge test, vibration membrane method 등 여러 가지가 제시되어 왔다. 이러한 방법들은 필름의 두께가 일정 두께 이상이 되어야 정확한 측정이 가능한 방법으로 매우 얇은 박막에서도 탄성특성을 평가할 수 있는 freehang, bridge 방법이 제시되었으며, 이 방법은 간단한 식각 공정을 통해 매우 얇은 박막에도 적용시킬 수 있다는 장점을 가지고 있다. 본 연구에서는 아주 얇은 박막에서도 탄성특성을 평가할 수 있는 freehang 방법을 이용하여 순수한 Diamond-like carbon (DLC) 필름과 Sidl 첨가된 DLC 필름의 탄성 특성을 평가하고자 한다. 실험에서 사용한 필름은 rf-PACVD 장비를 이용하여 증착하였다. 이때 전극과 플라즈마 사이의 바이어스 음전압은 -400 Vb로 합성압력은 10mTorr로 고정하였다. 사용한 반응 가스는 벤젠(C6H6), 그리고 벤젠과 희석된 실렌(SiH4 : H2 = 10 : 90)이며, 희석된 실렌의 첨가량을 조절하여 필름 내에 일정량의 Si을 함유시켰다. 각각의 조건에서 증착시간을 조절하여 필름의 두께를 변화시켰으며, KOH(5.6mol) 용액을 이용하여 습식 식각을 함으로써 freehang을 제작하였다. 이때 식각액에 의한 DLC 필름의 손상은 관찰되지 않았다. 필름의 잔류 응력을 측정하기 위해 200$\pm$10 혹은 100$\pm$5$\mu\textrm{m}$ 두께의 얇은 (100) Si wafer를 5$\times$50 mm2의 strip 형태로 절단하여 사용하였다. 필름의 압축 잔류 응력에 의해 발생한 필름/기판 복합체의 곡률은 laser 반사법과 $\alpha$-step profiler를 이용하여 측정하였으며, 이 결과를 Brenner 등에 유도된 식을 이용하여 잔류 응력을 계산하였다. 또한 제작된 frddhang은 광학 현미경과 전자주사현미경에 의해 관찰되었다. 이렇게 제작된 freehang을 이용하여 필름이 기판에 부착되기 위해 필요한 변형률을 측정하고, 독립적으로 측정된 필름의 잔류 응력을 박막의 응력-변형률 관계식에 적용하여 biaxial elastic modulus, E/(1-v)를 구할 수 있었다. 측정 결과 필름의 잔류 응력과 biaxial elastic modulus는 필름의 두께가 감소함에 따라 감소하는 경향을 나타냈으며, 같은 두께의 필름인 경우, 식각 깊이에 따른 biaxial elastic modulus 의 변화를 통해 최적의 식각 깊이를 알 수 있었다.

• Geomechanics and Engineering
• /
• v.17 no.6
• /
• pp.507-513
• /
• 2019

Reinforced soil and Expanded Polystyrenes (EPS) mixture (RSEM) is a geomaterial which has many merits, such as light weight, wide strength range, easy for construction, and economic feasibility. It has been widely applied to improve soft ground, solve bridge head jump, fill cavity in pipeline and widen highway. Reutilizing dredged sediment to produce RSEM as earthfill can not only consume a large amount of waste sediment but also significantly reduce the construction cost. Therefore, there is an urgent need understand the basic stress-strain characteristics of reinforced dredged sediment-EPS mixture (RDSEM). A series of cyclic triaxial tests were then carried out on the RDSEM and control clay. The effects of cement content, EPS beads content and confining pressure on the cyclic stress-strain behaviour of RDSEM were analyzed. It is found that the three stages of dynamic stress-strain relationship of ordinary soil, vibration compaction stage, vibration shear stage and vibration failure stage are also applicative for RDSEM. The cyclic stress-strain curves of RDSEM are lower than that of control clay in the vibration compaction stage because of its high moisture content. The slopes of backbone curves of RDSEMs in the vibration shear stage are larger than that of control clay, indicating that the existence of EPS beads provides plastic resistance. With the increase of cement content, the cyclic stress-strain relationship tends to be steeper. Increasing cement content and confining pressure could improve the cyclic strength and cyclic stiffness of RDSEM.

• The Journal of Korean Institute of Information Technology
• /
• v.16 no.11
• /
• pp.23-34
• /
• 2018

This paper presents the high efficiency and high power-factor power supply for LED lighting equipment. The proposed power supply is the single-stage power structure consisted of the full-bridge diode rectifier and flyback converter, and thus the power-factor correction and output voltage regulation are performed simultaneously using only one controller IC and one power semiconductor switch. Furthermore, the proposed power supply reduces the voltage stress and switching loss of main switch using the regenerative snubber, and it improves the system efficiency using the synchronous rectifier. The applied synchronous rectifier is the new voltage-driven type and its operation and construction are simple. In this paper, the operation principle of proposed power supply is explained through the operation analyses of its power-factor correction and main power conversion parts and the operation of synchronous rectifier is described, briefly. Also, a design example of the power circuit of 40W-class prototype is shown and the operation characteristics of proposed power supply are validated through the experimental results of the implemented prototype by the designed circuit parameter.

• KIPS Transactions on Software and Data Engineering
• /
• v.10 no.5
• /
• pp.161-168
• /
• 2021

Cracks affect the robustness of infrastructures such as buildings, bridge, pavement, and pipelines. This paper presents an automated crack detection system which detect cracks in diverse surfaces. We first constructed the combined crack dataset, consists of multiple crack datasets in diverse domains presented in prior studies. Then, state-of-the-art deep learning models in computer vision tasks including VGG, ResNet, WideResNet, ResNeXt, DenseNet, and EfficientNet, were used to validate the performance of crack detection. We divided the combined dataset into train (80%) and test set (20%) to evaluate the employed models. DenseNet121 showed the highest accuracy at 96.20% with relatively low number of parameters compared to other models. Based on the validation procedures of the advanced deep learning models in crack detection task, we shed light on the cost-effective automated crack detection system which can be applied to different surfaces and structures with low computing resources.

• Wind and Structures
• /
• v.35 no.4
• /
• pp.255-268
• /
• 2022

Light-weight or low-damped structures may encounter the unsteady galloping instability that occurs at low reduced wind speeds, where the classical quasi-steady assumption is invalid. Although this unsteady phenomenon has been widely studied for rectangular cross sections with one side perpendicular to the incidence flow, the effect of the mean wind angle of attack has not been paid enough attention yet. With four sectional models of different side ratios and geometric shapes, the presented research focuses on the effect of the wind angle of attack on unsteady galloping instability. In static tests, comparatively strong vortex shedding force was noticed in the middle of the range of flow incidence where the lift coefficient shows a negative slope. In aeroelastic tests with a low Scruton number, the typical unsteady galloping, which is due to an interaction with vortex-induced vibration and results in unrestricted oscillation initiating at the Kármán vortex resonance wind speed, was observed for the wind angles of attack that characterize relatively strong vortex shedding force. In contrast, for the wind angles of attack with relatively weak shedding force, an "atypical" unsteady galloping was found to occur at a reduced wind speed clearly higher than the Kármán-vortex resonance one. These observations are valid for all four wind tunnel models. One of the wind tunnel models (with a bridge deck cross section) was also tested in a turbulent flow with an intensity about 9%, showing only the atypical unsteady galloping. However, the wind angle of attack with the comparatively strong vortex shedding force remains the most unfavorable one with respect to the instability threshold in low Scruton number conditions.

• Journal of Technologic Dentistry
• /
• v.45 no.2
• /
• pp.39-47
• /
• 2023

Purpose: This study aimed to confirm the applicability of gloss polishing using automatic barrel finishing with respect to three-dimensional (3D)-printed resin specimens. The surface roughness and grinding angle of the 3D-printed resin specimens were observed with respect to gloss polishing time using automatic dental barrel finishing. Methods: Herein, experiments were conducted on four types of 3D-printed resin specimens. The specimens, with a thickness of 100 ㎛ each, were printed using a 3D printer. Subsequently, light polymerization was performed on these specimens for 15 min. Post this surface treatment, the specimens underwent grinding for 25 min. This process was followed by gloss polishing at 5-min intervals for up to 25 min using automatic dental barrel finishing. The specimens were photographed using a 3D optical microscope, and their surface roughness and grinding angle were measured. Results: The Ra (centerline average roughness) values of all the specimens, except for crown & bridge 10 group and those in the control group that were not polished using automatic barrel finishing, were <0.2 ㎛. However, polishing time needs to be controlled to realize the desired surface roughness and grinding amount considering the hardness of the resin used. Conclusion: Gloss polishing of 3D-printed resin can be realized using automatic dental barrel finishing. However, polishing time needs to be controlled to realize the desired surface roughness and grinding amount considering the hardness of the resin used.