• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1569-1576
• /
• 2014

This paper mainly proposes a direct torque control strategy to minimize torque ripple in brushless DC (BLDC) motor. BLDC motor has large current and torque ripple when one voltage vector applied in one cycle due to its low inductance. Hence, this paper proposed a hysteresis torque control with PWM mode to control the resultant torque. Moreover, when the direct torque control system is operating during the two-phase half-bridge $120^{\circ}$ conduction mode, large torque ripple in commutation area appears every 120 electrical degree. Based on analyzing the root of torque ripple in detail, lookup tables of switching devices states for new half-bridge modulation mode in the positive and negative reference torque put forwarded. Finally, simulations by MATLAB software and experiment results from DSP are presented to verify the feasibility and effectiveness of the proposed strategy operating in four-quadrant operation.

• Structural Engineering and Mechanics
• /
• 제81권1호
• /
• pp.59-68
• /
• 2022

Prestressed prefabricated hollow core concrete slabs with spans of 5 m and 10 m are commonly used since last century and still in service due to the advantage of construction convenience and durability. However, the end slabs are regularly subjected to cracks at the top and fail with brittleness due to the asymmetric boundary conditions. To better maintain such widely used type of hollow core slabs, the effect of asymmetric constraint in the end slabs are systematically studied through detailed nonlinear finite element analyses and experimental data. Experimental tests of slabs with four prestressed tendons and seven prestressed tendons with different boundary conditions were conducted. Results observe three failure modes of the slabs: the bending failure mode, shear and torsion failure mode, and transverse failure mode. Detailed nonlinear finite element models are developed to well match the failure modes and to reveal potential damage scenarios with asymmetric boundary conditions. Recommendations regarding ultimate capacity of the slabs with asymmetric boundary conditions are made to ensure a safe and rational design of prestressed concrete hollow slabs for short span bridges.

• Structural Monitoring and Maintenance
• /
• 제4권2호
• /
• pp.115-131
• /
• 2017

Classical flutter of wind turbine blades indicates a type of aeroelastic instability with fully attached boundary layer where a torsional blade mode couples to a flapwise bending mode, resulting in a mutual rapid growth of the amplitudes. In this paper the monitoring problem of onset of flutter is investigated from a detection point of view. The criterion is stated in terms of the exceeding of a defined envelope process of a specific maximum torsional vibration threshold. At a certain instant of time, a limited part of the previously measured torsional vibration signal at the tip of blade is decomposed through the Empirical Mode Decomposition (EMD) method, and the 1st Intrinsic Mode Function (IMF) is assumed to represent the response in the flutter mode. Next, an envelope time series of the indicated modal response is obtained in terms of a Hilbert transform. Finally, a flutter onset criterion is proposed, based on the indicated envelope process. The proposed online flutter monitoring method provided a practical and direct way to detect onset of flutter during operation. The algorithm has been illustrated by a 907-DOFs aeroelastic model for wind turbines, where the tower and the drive train is modelled by 7 DOFs, and each blade by means of 50 3-D Bernoulli-Euler beam elements.

• Journal of Power Electronics
• /
• 제10권1호
• /
• pp.27-33
• /
• 2010

This paper presents a bidirectional DC-DC converter suitable for low-voltage super capacitor-based electric energy storage systems. The DC-DC converter presented here consists of a full-bridge circuit and a current-fed push-pull circuit with a high frequency (HF) transformer-link. In order to reduce the device-conduction losses due to the large current of the super capacitor as well as unnecessary ringing, synchronous rectification is employed in the super capacitor-charging mode. A wide range of voltage regulation between the battery and the super capacitor can be realized by employing a Phase-Shifting (PS) Pulse Width Modulation (PWM) scheme in the full-bridge circuit for the super capacitor charging mode as well as the overlapping PWM scheme of the gate signals to the active power devices in the push-pull circuit for the super capacitor discharging mode. Essential performance of the bidirectional DC-DC converter is demonstrated with simulation and experiment results, and the practical effectiveness of the DC-DC converter is discussed.

• Steel and Composite Structures
• /
• 제10권6호
• /
• pp.541-561
• /
• 2010

This paper presents finite element analyses, experimental measurements and finite element model updating of an arch type steel laboratory bridge model using semi-rigid connections. The laboratory bridge model is a single span and fixed base structure with a length of 6.1 m and width of 1.1m. The height of the bridge column is 0.85 m and the maximum arch height is 0.95 m. Firstly, a finite element model of the bridge is created in SAP2000 program and analytical dynamic characteristics such as natural frequencies and mode shapes are determined. Then, experimental measurements using ambient vibration tests are performed and dynamic characteristics (natural frequencies, mode shapes and damping ratios) are obtained. Ambient vibration tests are performed under natural excitations such as wind and small impact effects. The Enhanced Frequency Domain Decomposition method in the frequency domain and the Stochastic Subspace Identification method in the time domain are used to extract the dynamic characteristics. Then the finite element model of the bridge is updated using linear elastic rotational springs in the supports and structural element connections to minimize the differences between analytically and experimentally estimated dynamic characteristics. At the end of the study, maximum differences in the natural frequencies are reduced on average from 47% to 2.6%. It is seen that there is a good agreement between analytical and experimental results after finite element model updating. Also, connection percentages of the all structural elements to joints are determined depending on the rotational spring stiffness.

• Steel and Composite Structures
• /
• 제16권1호
• /
• pp.21-44
• /
• 2014

The aim of this study is to determine the dynamic characteristics of long reinforced concrete highway bridges with post-tension tendons using analytical and experimental methods. It is known that the deck length and height of bridges are affected the dynamic characteristics considerably. For this purpose, Berta Bridge constructed in deep valley, in Artvin, Turkey, is selected as an application. The Bridge has two piers with height of 109.245 m and 85.193 m, and the total length of deck is 340.0 m. Analytical and experimental studies are carried out on Berta Bridge which was built in accordance with the balanced cantilever method. Finite Element Method (FEM) and Operational Modal Analysis (OMA) which considers ambient vibration data were used in analytical and experimental studies, respectively. Finite element model of the bridge is created by using SAP2000 program to obtain analytical dynamic characteristics such as the natural frequencies and mode shapes. The ambient vibration tests are performed using Operational Modal Analysis under wind and human loads. Enhanced Frequency Domain Decomposition (EFDD) and Stochastic Subspace Identification (SSI) methods are used to obtain experimental dynamic characteristics like natural frequencies, mode shapes and damping ratios. At the end of the study, analytical and experimental dynamic characteristic are compared with each other and the finite element model of the bridge was updated considering the material properties and boundary conditions. It is emphasized that Operational Modal Analysis method based on the ambient vibrations can be used safely to determine the dynamic characteristics, to update the finite element models, and to monitor the structural health of long reinforced concrete highway bridges constructed with the balanced cantilever method.

• 한국강구조학회 논문집
• /
• 제20권6호
• /
• pp.761-771
• /
• 2008

열차운행주파수가 철도교의 고유진동수와 일치하면, 철도교의 공진은 피할 수 없다. 또한, 열차가 교량을 매우 빠르게 통과하면, 계측 가능한 시간응답의 샘플 수는 매우 적다. 본 논문은 그러한 경우에 대하여 철도 교량의 동특성을 매우 효과적으로 추출할 수 있는 TDD기법과 SI기법을 소개한다. 열차통과 직후에 교량의 자유진동 시간응답구간의 상호상관을 이용하여 모드형상은 TDD기법으로 추출하고, 고유진동수 및 감쇠비 등의 시간변수들은 SI기법으로 추출한다. 경부고속철도 시스템에 위치한 2경간 강합성교량의 동특성 추출실험을 통하여 TDD기법과 SI기법의 현장 적용성이 검토되었다. 동특성 추정결과는 기존의 ERADC기법의 결과와 비교 검토되었다. 추정결과는 기존의 방법을 이용하여 획득된 결과와 매우 잘 일치한다.

• Structural Engineering and Mechanics
• /
• 제76권3호
• /
• pp.293-310
• /
• 2020

This study derives the differential equations of free vertical bending and torsional vibrations for two- and three-pylon suspension bridges using d'Alembert's principle. The respective algorithms for natural vibration frequency and vibration mode are established through the separation of variables. In the case of the three-pylon suspension bridge, the effect of the along-bridge bending vibration of the middle pylon on the vertical bending vibration of the entire bridge is considered. The impact of torsional vibration of the middle pylon about the vertical axis on the torsional vibration of the entire bridge is also analyzed in detail. The feasibility of the proposed method is verified by two engineering examples. A comparative analysis of the results obtained via the proposed and more intricate finite element methods confirmed the former feasibility. Finally, the middle pylon stiffness effect on the vibration frequency of the three-pylon suspension bridge is discussed. It is found that the vibration frequencies of the first- and third-order vertical bending and torsional modes both increase with the middle pylon stiffness. However, the increase amplitudes of third-order bending and torsional modes are relatively small with the middle pylon stiffness increase. Moreover, the second-order bending and torsional frequencies do not change with the middle pylon stiffness.

• 대한토목학회논문집
• /
• 제28권1A호
• /
• pp.95-104
• /
• 2008

본 연구에서는 경부고속철도상의 대표적인 교량인 2경간 연속보 형태의 고속철도 교량에 대하여 동적거동을 해석하고 공진발생의 감소방안들을 제시하였다. 하중은 한국형 고속철도하중인 총길이 380.15 m의 TGV-K 열차(2P+18T)가 일정한 속도로 이동하는 것으로 하였다. 동적거동을 모사하는 지배방정식은 질량과 강성이 분포된 연속계에서 만들어진 편미분방정식을 이용하여 구하였으며 Duhamel 적분을 이용한 모달계수의 처리를 수반하는 모드중첩법을 이용하여 동적해석을 수행하였다. 열차의 주행속도에 관계없이 동적거동을 급격히 감소시킬 수 있는 지간장이 존재하였으며 지금까지 연구된 단순보 형태의 교량에서 분석된 결과와는 달랐다. 열차의 주행속도에 의존하여 동적응답이 급격히 증가되어 공진현상을 일으키는 경우에도 공진을 감소시킬 수 있는 여러 방안들을 제시하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.3147-3155
• /
• 2011

Railway bridges are highly susceptible to resonance due to the equidistant axle load with constant speed of train. Thus, it is inevitable verify dynamic characteristics and quantities against dynamic guidelines. Recently, various new-type bridges are developed and applies to medium span length between 30m and 40m. However, just steel box girder bridge is under review for span length between 45m and 50m without development any new technologies. This study investigate the dynamic properties and safety of steel box railway bridge having span length 45m in alternative girder hight and kind of ballast. Numerical analysis is performed time series analysis by mode superposition using calculated natural vibration frequency and mode after carry out a free vibration analysis and extract modal parameter to higher modes. The results are then compared to various dynamic stability standards toward target bridge's dynamic stability analysis. The result of this study is expected as a reference for design railway bridges.