• 조명전기설비학회논문지
• /
• 제13권4호
• /
• pp.152-159
• /
• 1999

본 논문에서는 교류전압 인가시 모의 GIS내에 존재하는 금속이물의 거동현상에 대해 연구하였다. 평행평판 전극을 내장한 가스챔버를 설계·제작하고, 전국내 선형 및 구형의 금속이물에 대해 부상전압을 계산 및 측정하였다. 또한 각각의 금속이물에 대전되는 전하량을 계산하였다. 고속카메라를 이용하여 금속이물의 종류 및 인가전압에 따른 거동양상과 부상시간, 부상높이 등의 거동특성을 분석하였다. 전계인가시 금속이물의 대전 전하량은 금속이물의 크기에 따라 증가하며, 부상전압은 서형 및 구형 금속이물의 직경에 큰 양형을 받는 것으로 나타났다. 금속이물의 부상이후 부상전압 부근의 전압에서의 선형 금속이물은 후 전극과 거의 수직인 상태로 상하 왕복운동을 하며, 거의 수직상태로 움직이는 거동 형태를 나타내었다. 절연파괴전압에 가까운 전압에서는 금속이물은 부상 중에 수회 수직회전을 반복하며, 장시간 부유하였다.

• 조명전기설비학회논문지
• /
• 제22권4호
• /
• pp.114-120
• /
• 2008

일반적으로 22.9[kV] 이하의 케이블은 가교폴리에틸렌(XLPE)을 절연체로 사용하고 있다. XLPE내부의 결함으로 인한 사고로 경제적 및 인명피해가 발생한다. 이러한 사고에 대한 처리 기준이 마련이 되어 있지 않아 사고처리의 체계화가 시급히 필요한 실정이다. 본 연구에서는 XLPE 케이블의 사고 요인이 되는 전기적 열화현상에 대한 자료구축을 위하여 XLPE에 곡율반경이 $10[{\mu}m]$인 침천극을 삽입하여 절연파괴, 트리형상 및 연면방전 시료를 제작하였다. 단시간 파괴는 AC 60[Hz]의 전압을 1[kV/sec] 상승하였으며, 장기과전의 경우 AC 60[Hz]의 전압을 12[kV] 및 17[kV]를 인가하여 전기적 열화 특성에 대하여 실험을 하였다.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권2호
• /
• pp.138-144
• /
• 1994

Electrical conduction phenomena of $C_{22}$-quinolium(TCNQ) Langmuir- Blodgett(LB) films are reported through a study of current-voltage(I-V) characteristics along a perpendicular direction. The I-V characteristics were investigated by applying a step or a pulse voltage to the specimen as well as changing temperatures in the range of 20-250[.deg. C] It show an ohmic behavior in low-electric field, and a nonohmic behavior in high-electric field. This nonohmic behavior has been interpreted in terms of a conduction mechanism of space-charge limited current and Schottky effect. When the electric field is near the strength of 10$_{6}$ V/cm, there occur anomalous phenomena similar to breakdown. When step or pulse voltage is applied, the breakdown voltage shifts to the higher one as the step or pulse time width becomes shorter. To see the influence of temperature, current was measured as a function of temperature under the several bias voltages, which are lower than that of breakdown. It shows that the current increases to about 103 times near 60-70[.deg. C], and remains constant for a while up to around 150[.deg. C] and then suddenly drops. We have also performed a DSC(differential scanning calorimetry) measurement with $C_{22}$-quinolium(TCNQ) powder in the range of 30-300[.deg. C]. These results imply that the anomalous phenomena occuring in the high electric field are caused by the electrical and internal thermal effect such as a joule heating.ating.

• 전기전자학회논문지
• /
• 제26권3호
• /
• pp.333-340
• /
• 2022

고전압용 정전기 보호소자인 DDDNMOS(double diffused drain N-type MOSFET) 소자의 더블 스냅백 방지를 위한 최적의 이온주입 조건을 결정하기 위해 공정 및 소자 시뮬레이션이 수행되었다. HP-Well, N^- 드리프트 및 N⁺ 드레인 이온주입량의 변화가 더블 스냅백 및 애발란치 브레이크다운 전압에 미치는 영향을 고찰함으로써 더블 스냅백을 방지하여 정전기 보호 성능 개선할 수 있었다. HP-Well 영역보다는 N^- 드리프트 영역의 이온주입 농도를 최적으로 설계할 경우, 1차 on 상태에서 2차 on 상태로 전이하는 것을 막아주므로 비교적 양호한 정전기 보호 성능을 얻을 수 있었다. 또한 드리프트 이온주입 농도는 누설전류 및 애발란치 브레이크다운 전압에도 영향을 미치므로 동작전압이 30V보다 큰 공정기술에서는 DPS와 같은 새로운 구조를 적용하거나, 대안으로 여러 공정 변수들을 종합(colligation)하여 적용할 경우 향상된 정전기 보호 성능을 실현할 수 있을 것이다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 춘계학술대회 논문집
• /
• pp.204-207
• /
• 1995

This paper deals with the dielectric characteristics of $SF_{6}$ gas stressed by non-oscillating and oscillating impulse voltages in inhomogeneous field perturbed by a fixed needle shaped-protrusion. The breakdown voltage-time characteristics were measured for both polarities and over the gas pressure range from 0.1 to 0.5 [MPa], and the temporal developments of the prebreakdown were observed. The dependence of the leader stepping time on the gas pressure were obtained.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.166-170
• /
• 1991

An advanced on-resistance model of VDMOS devices in the low voltage regime is proposed and verified by 2-D device simulations. The model considers the lateral gaussian doping profiles in the channel region and exact current spreading angles in the epitaxial layer for both linear and cellular geometries by employing the conformal mapping. It is found out that the on-resistance of low voltage VDMOS may be overestimated considerably if it is analyzed by the conventional method. The 2-D device simulation results show that the proposed model is valid for all ranges of cell spacings and breakdown voltages.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.915-917
• /
• 1992

This paper shows the discharge characteristics in flowing air with variation of tempearature(T) under the needle-needle gap. Flowing air duct of this investigation is circular tube. The flow at the experimental position's section is described as fully developed laminar flow. The important results obtained from this study are as follows. The ratio sparkover voltages to the Reynolds number(Re) increases with decreasing the Re. The velocity profiles can be visualized by this experimental method. The breakdown voltage ($V_{s1}$) for variation of T at 1[m/s] can be expressed by $V_{s1}$ = $K_1$(23.98$\rho$d + 6.98$\sqrt{\rho{d}}$) [kV].

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1471_1472
• /
• 2009

In a wide variety of high-voltage applications surface flashover plays major role in the system's performance and yet has not been studied in great detail for vacuum conditions with modern diagnostic tools. surface flashover for both direct current and pulsed voltages in considered. within the setup, parameters such as geometry, material characteristics of the applied voltage can be altered. This paper review surface flashover of insulator, primarily in vacuum. It discusses theories and models relating to surface flashover and experimental results. surface flashover of insulators in vacuum generally is initiated by the emission of electrons from the cathode triple junction point (the region where the electrode, insulator, vacuum). the electrode material was copper, and a AC voltage was applied between the electrodes. these results were compared with the surface flashover characteristic of insulator at results, surface flashover influenced only insulator surface condition. and increasing vacuum pressure was risen breakdown voltage.

• 전기학회논문지
• /
• 제65권11호
• /
• pp.1894-1899
• /
• 2016

In this paper, because the position sensor represents the important factor in BLDC (Brushless DC) motor drives, BLDC motor is necessary that the three Hall-sensors evenly be distributed around the stator circumference in case of the 3 phase motor. The Hall-sensor is set up in this motor to detect the main flux from the rotor. So the output signal from Hall-sensor is used to drive IGBT to control the stator winding current. However, in case of breakdown Hall sensor, we research that the estimation algorithm of Hall sensor signal to detect rotor position and for the speed feedback signals with BLDC motor whose six stator and two rotor designed. In addition, this paper presents a sensorless speed control of BLDC Motor using terminal voltage of the one phase. Rotor position information is extracted by indirectly sensing the back EMF from only one of the three terminal voltages for a three-phase BLDC motor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 추계학술대회 논문집 학회본부
• /
• pp.179-182
• /
• 1988

This study is to investigate the adhesive strength of composite material's interface on the experimental methode of tree growth in the material. The results are as fellows 1) The irradiations of ultrasonic energy cause the mechanical vibration in the polymer composite materials of fluid state, so then bring about physical dispersion and heat form inorganic materials, being supposed to produce chemical crosslinking reaction, decreasing of voids between filler and matrix. 2) The characterics of the breakdown are increased by using coupling agent in the composite material. 3) As the intensity of ultrasonic energy and its irradiated time are larger, the tree inception and break-down voltages increase and the tree growing is slower. so we obtain that the interface adhesive force tan be strengthened by the irradiation of ultrasonic energy.