• Nuclear Engineering and Technology
• /
• v.15 no.4
• /
• pp.219-228
• /
• 1983

The blowdown history of the TMI-2 accident up to the isolation of the relief valve associated with a small break LOCA is reviewed briefly. An analysis is made to determine what instruments should be added in the core in order to prevent core damage in the case of the TMI-2 accident. With the added instruments a procedure is presented on how to predict the uncovered level of the core and how to calculate operator time margin. Sample calculations are done for the TMI-2 accident to determine the uncovered level and operator time margin. Finally, the map to show the uncovered level of the core and operator time margin is drawn with measurable parameters by the above methods.

• Explosives and Blasting
• /
• v.20 no.2
• /
• pp.7-19
• /
• 2002

The cut is placed high up in the section, the 1st sloping holes below the cut, and divided all the holes located below the 1st sloping holes into a certain area with longitudinal section, to lower pollution made from tunnel blasting. With the sequential blasting machine, after I first blasted holes around the cut holes by a pre-splitting method, blasted the cut area and the 1st sloping holes. The 1st and 2nd sloping holes divided areas are initiated gradually to free face upwards made by the cut. Especially, I pre-splinted contour holes previous blast the before sloping holes from the contours. The ground vibration from the earth surface just over the advance face decreased about 42.0% compare with the down blasting method under the condition of equal charge weight per delay. I controlled the crack and over break of the mother rock by pre-splitting contour holes before blast the first sloping holes from the contours. The peak values of noise and air blast by blasting decreased about 10dB more than the down blasting method. the noise and air blast diminished gradually as a round. The throw distance of the fly rock was decreased about 55%.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.3
• /
• pp.30-35
• /
• 2007

Folding performance is very important in box manufacturing process using paperboard. To evaluate the folding performance of various paperboards, we measured the folding moment and folding behavior at the different folding angle and rate conditions. When linerboard with grammage of $300\;g/m^2$ was folded up to $90^{\circ}$, the compression break and delamination of sheet were observed. The maximum folding moment was little affected by folding angle, but it was increased logarithmically with folding rate. And the effect of paperboard thickness was significant. The maximum folding moment of MD sample was higher than one of CD sample by 40%.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2021.04a
• /
• pp.52-52
• /
• 2021

Persicaria amphibia as an England native plant, is a rhizomatous perennial, one of the rather amphibious plants. Its aquatic form contains water-soluble sugars, starch, and protein. P. amphibia have up to 18% tannins in stems and rhizomes. Previous studies have confirmed the anti-inflammatory activity of live bacteria roots, but no studies on bioactivity are known. DNA damage responses (DDRs) pathways are considered a crucial factor affecting the alleviation of cellular damage. The ataxia-telangiectasia mutated and Rad3 related (ATM) and checkpoint kinase 2 (Chk2) pathways are the main pathways of DNA damage response. Also, p53 is a key integrator of cellular response to oxidative DNA damage, contributing repair, or leading transcription including apoptosis. In the present study, we conducted an investigation into the inhibitory effects of P. amphibia on oxidative DNA damage for confirming potential to complementary medicine and therapies. In conclusion, P. amphibia can provide protective effects against double-stranded DNA break (DSB) caused by oxidative DNA damage.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.47 no.1
• /
• pp.20-27
• /
• 2024

Determining the number of operators who set up the machines in a human-machine system is crucial for maximizing the benefits of automated production machines. A man-machine chart is an effective tool for identifying bottlenecks, improving process efficiency, and determining the optimal number of machines per operator. However, traditional man-machine charts are lacking in accounting for idle times, such as interruptions caused by other material handling equipment. We present an adjusted man-machine chart that determines the number of machines per operator, incorporating idleness as a penalty term. The adjusted man-machine chart efficiently deploys and schedules operators for the hole machining process to enhance productivity, where operators have various idle times, such as break times and waiting times by forklifts or trailers. Further, we conduct a simulation validation of traditional and proposed charts under various operational environments of operators' fixed and flexible break times. The simulation results indicate that the adjusted man-machine chart is better suited for real-world work environments and significantly improves productivity.

• Ocean Systems Engineering
• /
• v.14 no.2
• /
• pp.157-169
• /
• 2024

The sudden release of water from a dam failure can trigger bores on a flat surface and exert substantial impact forces on structures. This flow poses a high-risk flood hazard to downstream urban areas, making it imperative to study its impact on structures and devise effective energy dissipators to mitigate its force. In this study, a combination of Genetic Algorithm optimization and numerical modeling is employed to identify the optimal energy dissipator. The analysis reveals that a round arc-shaped structure proves most effective, followed by a triangular shape. These shapes offer wide adaptability in terms of structure dimensions. Structures with higher elevation, especially those with round or triangular shapes, demonstrate superior energy dissipation capabilities. Conversely, square-shaped structures necessitate minimal height to minimize impact forces. The optimal width for dissipating energy is found to be 0.9 meters, allowing for effective wave run-up and propagation. Furthermore, the force exerted on structures increases with higher initial water levels, but diminishes with distance from the dam, highlighting the importance of placement in mitigating impact forces.

• Journal of Bio-Environment Control
• /
• v.17 no.2
• /
• pp.150-156
• /
• 2008

The influences of night break by costly artificial light sources were investigated on the photo-morphogenesis and growth of leafy perilla (Perilla ocymoides L.). The irradiation of red, blue, and three-colored light for night break significantly increased the stem length and stem diameter compared to dark. Three-colored light gave the highest fresh and dry weight of stem, followed by red and blue light. Floral induction was suppressed up to 100 days after the night break, by red and three-colored light, but the plants grown under the dark or treated with blue light showed 85% and 31% flowering rate, respectively. The time needed for floral induction after night break was 60 days in dark and 80 days in blue light. The number of leaf, leaf area, and fresh weight per plant were the highest in red and three-colored light night break, followed by blue light and dark. The photosynthetic rate observed 80 days after night break was the highest in red light, followed by blue and three-colored light. A low light compensation point of $20\;{\mu}mol\;m^{-2}{\cdot}s^{-1}$ was observed in three-colored light, while red and blue light tended to show higher measurements.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.4
• /
• pp.305-330
• /
• 2023

Unlike NATM tunnels, Shield TBM tunnels have split linings. Therefore, the stress distribution of the lining is different even if the lining is under the same load. Representative methods for analyzing the stress generated in lining in Shield TBM tunnels include Non-joint Mode that does not consider connections and a 2-ring beam-spring model that considers ring-to-ring joints and segment connections. This study is an analysis method by Break-joint Mode. However, we do not consider the structural role of segment lining connections. The effectiveness of the modeling is verified by analyzing behavioral characteristics against vibration loads by modeling with segment connection interfaces to which vertical stiffness and shear stiffness, which are friction components, are applied. Unlike the Non-joint mode, where the greatest stress occurs on the crown for static loads such as earth pressure, the stress distribution caused by contact between segment lining and friction stiffness produced the smallest stress in the crown key segment where segment connections were concentrated. The stress distribution was clearly distinguished based on segment connections. The results of static analysis by earth pressure, etc., produced up to seven times the stress generated in Non-joint mode compared to the stress generated by Break-joint Mode. This result is consistent with the stress distribution pattern of the 2-ring beam-spring model. However, as for the stress value for the train vibration load, the stress of Break-joint Mode was greater than that of Non-joint mode. This is a different result from the static mechanics concept that a segment ring consisting of a combination of short members is integrated in the circumferential direction, resulting in a smaller stress than Non-joint mode with a relatively longer member length.

• Journal of the Korean Society of Safety
• /
• v.9 no.1
• /
• pp.100-109
• /
• 1994

In this study, it is investigated that the possibility of the numerical simulation for the incineration of the hazardous material, crbon tetrachloride($CCl_4$). A 3-dimensional numerical technology is applied for turbulent reacting flows of the full-scale Dow Chemical incinerator. The calculations are made by a CRAY-2S, super computer. The major parameters considered in this study are kiln revolution rate (rpm), filling ratio of the solid waste(f), burner Injection velocity and angle, and turbulent air jets for swirl. And the employed turbulent reaction model is the eddy break-up model which is a kind of fast chemistry model assuming general equilibrium and used for a premixed flame. The calculated flow fields are presented and discussed. 1) The presence of turbulent air nozzles for swirl gives rise to visible increase of the convective motion over the region of the solid waste. This implies the possibility to enhance the mixing of the waste with the surrounding all and thereby to reduce thermal and species stratification, which were reported in a large rotary kiln operation. 2) Considering that the location of the recirculation region has a strong relation with the heating rate of the solid waste, the control of the recirculation region by the burner injection angle Is quite desirable in the sense of the flexible design of the rotary kiln incinerator for a carbon tetrachloride. 3) Finally, it is found that the eddy break-up model Is not suitable for carbon tetrachloride($CCl_4$) because this model is not incorporated the flame inhibition trend due to the presence $CCl_4$compound.

• Journal of Korean Ophthalmic Optics Society
• /
• v.12 no.3
• /
• pp.27-33
• /
• 2007

This research investigated the effects of spherical and aspherical R.G.P lenses which was performed by optometrists in In-Cheon and Kyung-Gi region. This research survey included various questions such as the fitting status, after-care method, preliminary test. Results of the survey revealed that the optometriests sold the asperical and spherical lenses with a ratio of 7:3, respectively, and most of them did not cheked Topography, Fluorescein test by slit lamp biomicroscope, Tear Break up time test, Schirmer test and so on. And, with fitted R.G.P lenses symptoms like light odd-feeling, congestion, eye-stimulus, dimness and dryness were frequently reported. The purposes of this study are to search for the ideal fitting check of R.G.P lens and remind the most important preliminary test for contact lens fitting.