• International Journal of Concrete Structures and Materials
• /
• v.11 no.2
• /
• pp.343-363
• /
• 2017

The objective of this work was finding out the most advisable testing conditions for an effective and robust characterization of the tensile strength (TS) of concrete disks. The independent variables were the loading geometry, the angle subtended by the contact area, disk diameter and thickness, maximum aggregate size, and the sample compression strength (CS). The effect of the independent variables was studied in a three groups of experiments using a factorial design with two levels and four factors. The likeliest location where failure beginning was calculated using the equations that account for the stress-strain field developed within the disk. The theoretical outcome shows that for failure beginning at the geometric center of the sample, it is necessary for the contact angle in the loading setup to be larger than or equal to a threshold value. Nevertheless, the measured indirect tensile strength must be adjusted to get a close estimate of the uniaxial TS of the material. The correction depends on the loading geometry, and we got their mathematical expression and cross-validated them with the reported in the literature. The experimental results show that a loading geometry with a curved contact area, uniform load distribution over the contact area, loads projected parallel to one another within the disk, and a contact angle bigger of $12^{\circ}$ is the most advisable and robust setup for implementation of BT on concrete disks. This work provides a description of the BT carries on concrete disks and put forward a characterization technique to study costly samples of cement based material that have been enabled to display new and improved properties with nanomaterials.

• Economic and Environmental Geology
• /
• v.32 no.2
• /
• pp.203-208
• /
• 1999

The main objective of this study is to suggest a new assessment method of the influence of weathering due to salt crystallization on the engineering property of rock. For this purpose, various sources of salt and salt crystallization were investigated, and artificially accelerated weathering tests were carried out. In natural envionment, weathering rate is very slow and weathering process involves complex mechanisms. Therefore artificial weathering test is essential for systematic analysis. Arificial weathering test is defined as test which controls weathering rate and agents by controlling arificial environmental condition. In this study, salt crystallization test was selected among various artificial weathering test methods, for its important role in weathering. Change of various stone properties were detexted. The change of physical properties by salt crystallization were observed as follows : 72% in Brazilian tensile strength and 72% in Slake durability. These results explain the importance of salt crystallization in the mechanical behaviour and properties of stone.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1057-1062
• /
• 2008

In order to investigate a strength anisotrophy of basalt in Cheju Island, rock samples of Pyosenri basalt, trachy-basalt and scoria were taken from Seoguipo-Si Seongsan-Eup area, and a series of uniaxial compressive strength test and Brazilian test were carried out. The strengths were decreased with increasing the moisture contents in rock sample by pore water. As the result of test considering the anisotropy of rock strength, the compressive strength in condition of failure occurred parallel to stratified layer is decreased about 12-26% more than that in condition of failure occurred inclined to stratified layer.

• Computers and Concrete
• /
• v.18 no.1
• /
• pp.39-51
• /
• 2016

This paper considers the tensile strength of concrete samples in direct, CTT, modified tension, splitting and ring tests using both of the experimental tests and numerical simulation (particle flow code 2D). It determined that which one of indirect tensile strength is close to direct tensile strength. Initially calibration of PFC was undertaken with respect to the data obtained from Brazilian laboratory tests to ensure the conformity of the simulated numerical models response. Furthermore, validation of the simulated models in four introduced tests was also cross checked with the results from experimental tests. By using numerical testing, the failure process was visually observed and failure patterns were watched to be reasonable in accordance with experimental results. Discrete element simulations demonstrated that the macro fractures in models are caused by microscopic tensile breakages on large numbers of bonded discs. Tensile strength of concrete in direct test was less than other tests results. Tensile strength resulted from modified tension test was close to direct test results. So modified tension test can be a proper test for determination of tensile strength of concrete in absence of direct test. Other advantages shown by modified tension tests are: (1) sample preparation is easy and (2) the use of a simple conventional compression press controlled by displacement compared with complicate device in other tests.

• Explosives and Blasting
• /
• v.22 no.1
• /
• pp.81-91
• /
• 2004

Samples examined in this paper were selected from Samwoo building stone, Sinra building stone, Gana building stone, and Chung gin building stone in Kyunggi province and Whakwang industry, Gomoch building stone, and Sejin building stone in Kyungbuk province. The point of this study is to examine the physical and mechanical features of Pochun rock, Munkyung rock and Ildong rock through specific gravity, porosity, absorption, point load test, triaxial compressive test Brazilian test, petrology test and chemical analysis test.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.11
• /
• pp.15-26
• /
• 2007

Los Angeles abrasion loss test has usally been applied to the quarry for the purpose of aggregate hardness estimation. 324 blocks from 25 sites of Kyeongsang basin samples of sedimentary rock were examined and tested in laboratary. This paper found that L. A. abrasion loss test is a good method to estimate engineering index such as uniaxial compressive strength, elastic modulus, indirect tensile strength, point load strength index, Schmidt hammer rebound value of sedimentary rocks with high correlation factor. Engineers will prefer L. A. abrasion loss test to the other one for design and construction as this method is quick and easy.

• Structural Engineering and Mechanics
• /
• v.71 no.1
• /
• pp.77-87
• /
• 2019

In this paper, the interaction between two neighboring tunnel has been investigated using PFC2D. For this purpose, firstly calibration of PFC was performed using Brazilian experimental test. Secondly, various configuration of two neighboring tunnel was prepared and tested by biaxial test. The maximum and minimum principle stresses were 0.2 and 30 MPa respectively. The modeling results show that in most cases, the tensile cracks are dominant mode of cracks that occurred in the model. With increasing the diameter of internal circle, number of cracks decreases in rock pillar also number of total cracks decreases in the model. The rock pillar was heavily broken when its width was too small. In fixed quarter size of tunnel, the crack initiation stress decreases with increasing the central tunnel diameter. In fixed central tunnel size, the crack initiation stress decreases with increasing the quarter size of tunnel.

• Structural Engineering and Mechanics
• /
• v.68 no.4
• /
• pp.507-517
• /
• 2018

In this research the effect of bedding layer angle and bedding layer thickness on the shear failure mechanism of concrete has been investigated using PFC3D. For this purpose, firstly calibration of PFC3d was performed using Brazilian tensile strength. Secondly punch shear test was performed on the bedding layer. Thickness of layers were 5 mm, 10 mm and 20 mm. in each thickness layer, layer angles changes from $0^{\circ}$ to $90^{\circ}$ with increment of $25^{\circ}$. Totally 15 model were simulated and tested by loading rate of 0.016 mm/s. The results show that when layer angle is less than $50^{\circ}$, tensile cracks initiates between the layers and propagate till coalesce with model boundary. Its trace is too high. With increasing the layer angle, less layer mobilizes in failure process. Also, the failure trace is very short. It's to be note that number of cracks decrease with increasing the layer thickness. The minimum shear punch test strength was occurred when layer angle is more than $50^{\circ}$. The maximum value occurred in $0^{\circ}$. Also, the shear punch test tensile strength was increased by increasing the layer thickness.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.10
• /
• pp.4769-4774
• /
• 2016

Objective: To analyze the survival of elderly patients with breast cancer according to the type of treatment used. Methods: A cohort study of women aged 80 or over with breast cancer registered with the Brazilian National Cancer Institute (Instituto Nacional do $C{\hat{a}}ncer$ - INCA) between 2008 and 2009 was conducted. Prognosis was analyzed according to the cancer treatment performed: surgery, radiotherapy, or hormone therapy. Analysis of the overall 5-year survival rate was performed using the Kaplan - Meier method, and comparisons of curves were undertaken using the log-rank test. For multiple regression analysis, Cox regression was used, adjusting for age and clinical stage, considering values of p < 0.05 as significant. Data were all analyzed using the statistical package SPSS version 20. Results: 70 women with a mean age of $84.0{\pm}3.7years$ at diagnosis participated in the study. The median follow-up time was 37.1 months (range 0.5-75.5), and 31 deaths (44.3%) occurred during this time. The median survival time was 51.2 months (95% CI, 44.9-57.4), higher in those who underwent surgery (p = 0.012) and those who had hormone therapy (p=0.001). Treatment with surgery reduced the risk of death by 61.7% (HR 0.3; 95% CI, 0.1-0.6; p = 0.001) when adjusted for clinical stage and age at diagnosis. However, there was no significant benefit from radiotherapy (HR 1.2; 95% CI, 0.5-2.5; p = 0.694). Conclusion: Treatment with surgery and hormone therapy increased the survival of our Brazilian patients with breast cancer aged 80 or over.

• Smart Structures and Systems
• /
• v.22 no.5
• /
• pp.611-620
• /
• 2018

In this research the effect of bedding layer angle and bedding layer thickness on the shear failure mechanism of concrete has been investigated using PFC3D. For this purpose, firstly calibration of PFC3d was performed using Brazilian tensile strength. Secondly shear test was performed on the bedding layer. Thickness of layers were 5 mm, 10 mm and 20 mm. in each thickness layer, layer angles changes from $0^{\circ}$ to $90^{\circ}$ with increment of $25^{\circ}$. Totally 15 model were simulated and tested by loading rate of 0.016 mm/s. The results shows that when layer angle is less than $50^{\circ}$, tensile cracks initiates between the layers and propagate till coalesce with model boundary. Its trace is too high. With increasing the layer angle, less layer mobilize in failure process. Also the failure trace is very short. It's to be note that number of cracks decrease with increasing the layer thickness. The minimum shear test strength was occurred when layer angle is more than $50^{\circ}$. The maximum value occurred in $0^{\circ}$. Also, the shear test tensile strength was increased by increasing the layer thickness.