• 박물관보존과학
• /
• 제16권
• /
• pp.56-81
• /
• 2015

족자 고리는 끈이나 유소를 고정시켜 걸 수 있도록 하는 장황 부속품으로 형태가 다양하며 여러 금속재를 사용하여 제작되었다. 현재 전통 형식의 고리는 대부분 개장으로 인해 유실되었으며, 일본식 고리를 사용하고 있다. 따라서 본 연구에서는 국립중앙박물관에 소장된 전통 족자 19점을 대상으로 고리의 형태와 제작기법, 성분을 조사하여 옛 형태를 복원해 보고자 하였다. 의궤 내용에서 고리는 원환(圓環), 국화동(菊花童), 배목(排目) 등 고유의 명칭으로 기록되어 있다. 휴대용 엑스선 형광분석기(portable X-ray fluorescence, Artax, Rontec)로 성분을 분석한 결과, 전통 형식의 고리는 황동, 철, 은-구리합금 등 다양한 금속재로 확인되었다. 구리와 아연이 주성분인 황동은 17점 족자 고리에 사용되었다. 전 윤시달 초상(신2339)의 배목에서는 철을 사용하였으며, 주석-납 합금으로 도금하였다. 이서구 초상(신1065)에서는 고리 전체가 은-구리합금으로 제작되었음을 확인하였다. 광학현미경(Leica, M205A)으로 제작 방법을 조사한 결과 원환은 금속봉을 절단한 뒤 둥글게 휘어 만든 유형과 주조로 제작된 유형으로 확인되었다. 배목은 주조한 합금으로 봉재나 판재를 만들고 다시 단조과정을 거쳐 제작하였고, 배목장식은 금속판재를 잘라 형태를 만든 후 축조와 타출기법 등으로 무늬를 새겨 장식하였다.

• 한국주조공학회지
• /
• 제17권5호
• /
• pp.450-457
• /
• 1997

Effects of Ti addition and homogenizing heat treatment on the mechanical properties in Cu-Zn-Al alloy (high strength yellow brass) were investigated. Grain refinement was successfully achieved by Ti addition. The microstructure, which was composed of island or fine feather-like branched Ti compounds was changed to feather-like eutectic microstructure as the content of Ti increased. The highest hardness value was obtained for 0.5 wt.% Ti specimen and the second was Ti non-added specimen in as-cast condition. The highest tensile strength was obtained for 0.5 wt.% Ti specimen. Because of the presence of cast defects and worse castability, tensile strength decreased as the content of Ti increased. Elongation increased with increasing homogenizing time and temperature; remarkable increase was obtained for $400^{\circ}C$ homogenizing temperature in the 0.5 wt.% Ti specimen. For $500^{\circ}C$ and $600^{\circ}C$ homhgenizing, temperature, high elongation was obtained in 2 and 4 wt.% Ti specimen.

• Restorative Dentistry and Endodontics
• /
• 제4권1호
• /
• pp.7-9
• /
• 1978

Brass specimen, copper based alloy was prepared in cubic form about $1cm{\times}1cm{\times}1cm$ in volume. The specimens were mechanically compressed in one direction until the dimension distorted to 20%, 40%, 60% and 80% in length. The compressed specimens with 80% distorted in length were then heat treated in $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$ and $600^{\circ}C$ for 30 minutes. Microscopic examination was made on both compressed and heat treated specimens. The results obtained from the study were as follows: 1. Grain boundary and twin phenomenon was clearly seen in 0% and 20% compressed cases. Slip bands was appeared in 40% cases and distributed equally as well as twin. 2. The first evidence of slip bands was observed in 20% and the bands grew thicker and denser as the compression increased. 3. The density of the bands were reduced after annealing in $200^{\circ}C$ and completely disappeared at $300^{\circ}C$ cases. 4. Recrystallization was noticed unevenly in $300^{\circ}C$ cases and the evidence of twin was observed in these crystallized area. 5. In $400^{\circ}C$ cases the grain boundary was evenly found and the twin phenomenon was clearly observed. Grain boundary and twin was noticeably formed in size according to the annealing temperature increased.

• 한국정밀공학회지
• /
• 제1권2호
• /
• pp.58-68
• /
• 1984

In this study, the static and dynamic components of cutting resistance were measured with tool dynamometer (Swiss, pieso-electric type) when S45C, A1-alloy and brass were drilled under the some variable conditions. The results obtained are as follows; 1) The dynamic components of these cutting resistance are not related to the depth of drilled hole. 2) The static and dynamic components of cutting resistance are increased in accordance with the increase of feed and drill diameter. 3) The dynamic components of thrust force are increased in accordance with the increase of spindle speed. 4) The rate of the dynamic component to the static component is 0.3 .approx. 0.5 in torque, 0.1 .approx. 0.2 in thrust force. 5) The characteristic of the tool system is affected in dynamic component of cutting resistance, and the creasted frequency and amplitude of the chip are determined by the crilled materials. 6) The maximum amplitude of the dynamic component is increased proportionally in accordance with the feed rate and the spindle speed.

• 한국공작기계학회논문집
• /
• 제16권1호
• /
• pp.80-85
• /
• 2007

High speed cutting is a machining process which cuts materials with the fast movement and rotation of a spindle in a machine tool. High speed cutting leaves a plastically deformed layer on the machined surface. This deformed layer affects in various forms to the surface roughness of machined parts such as the dimensional instability, the micro crack. The surface roughness is called surface integrity which is very important in precision cutting. This paper aims to study on the machined surfaces characteristics of aluminum alloy and brass by AFM(Atomic force microscope) measurement. The objective is contribution to ultra- precision cutting by exhibit foundation data of surface roughness and tool wear when parts are cutting with diamond tool at the factory.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.884-887
• /
• 2000

In the present industry, there is not only the cutting of iron metal, but also the cutting of alloy aluminum, brass and plastic to wood(Paulownia). A variety of material is used and these industry is made need of the cutting material but lots of experiments processing is not enough at the moment. At this point, our team processed the basic experiment about influencing of Feedrate and Backrake angle of bite concerned to manufacture in the turning of non-iron metal. Generally speaking, we recognized that there was occurrence of increase of Surface Roughness with increasing of cutting angle in the non-iron metal, but in the cutting of wood we knew, there was special change with change of cutting angle

• Journal of Biosystems Engineering
• /
• 제23권2호
• /
• pp.187-194
• /
• 1998

This study was carried out to investigate mechanical properties o major part for agricultural machinery in Korea. The results are as follows ; 1. The mechanical Properties for heat resisting steel bars, alumium alloy castings, carbon steel for machine structural use, chromium molybdenum steels, high strength brass castings and carbon tool steels are proper for Korean standard. 2. The mechanical properties fir spring steels used to mould board, share of plow and blade of rotary are not suitable to Korean standard. Ⅰ think that a counterplan for quality rising is necessary such as supply of good quality materials and improvement of new materials in Korean agricultural machinery.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.236-241
• /
• 2000

In the present industry, there is not only the cutting of iron metal, but also the cutting of alloy aluminum, brass and plastic to wood(Paulownia). A variety of material is used and these industry is made need of the cutting material but lots of experiments processing is not enough at the moment. At this point, our team processed the basic experiment about influencing of cutting angle of bite concerned to manufacture in the turning of non-iron metal. Generally speaking, we recognized that there was occurrence of increase of rough surface with increasing of cutting angle in the non-iron metal. but in the cutting of wood we knew, there was special change with change of cutting angle.

• Tribology and Lubricants
• /
• 제36권2호
• /
• pp.88-95
• /
• 2020

In this study, we investigate the mechanical properties of high manganese steel, and the friction and wear characteristics of brake friction material containing this steel, for passenger car application, with the aim of replacing copper and copper alloys whose usage is expected to be restricted in the future. These steels are prepared using a vacuum induction melting furnace to produce binary and ternary alloys. The hardness and tensile strength of the high manganese steel decrease and the elongation increases with increase in manganese content. This material exhibits high values of hardness, tensile strength, and elongation; these properties are similar to those of 7-3 brass used in conventional friction materials. We fabricate high manganese steel fibers to prepare test pad specimens, and evaluate the friction and wear characteristics by simulating various braking conditions using a 1/5 scale dynamometer. The brake pad material is found to have excellent friction stability in comparison with conventional friction materials that use 7-3 brass fibers; particularly, the friction stability at high temperature is significantly improved. Additionally, we evaluate the wear using a wear test method that simulates the braking conditions in Europe. It is found that the amount of wear of the brake pad is the same as that in the case of the conventional friction material, and that the amount of wear of the cast iron disc is reduced by approximately 10. The high manganese steel is expected to be useful in the development of eco-friendly, copper-free friction material.

• 한국재료학회지
• /
• 제4권8호
• /
• pp.877-887
• /
• 1994

강도, 소전율, 스프링성, 내열성 및 굽힘 가공성등의 적절한 조화를 갖는 콘넥팅재료를 개발하기 위하여 Cu-Ni-Si-P합금에 대하여 연구하였다. Ni와 Si의 조성을 달리한 3종류의 합금을 용해, 주조하여 약 $900^{\circ}C$에 열간압연 후 수냉하고, 그 후 냉간압연하여 $450^{\circ}C$. $500^{\circ}C$ 및 $550^{\circ}C$에서 시효처리한 후 기계적 성질 변화와 도전율 등을 조사하였다. 고강도와 고존도율의 적절한 조화를 나타내는 Cu-2.7%Ni-0.53% Si-0.029%P 합금을 만들었다. 합금 1을 0.5mm두께의 콘넥팅재료로 가공한 후 여러가지 특성은 인청동(C 5210R-H)과 황동(C2600R-EH)에 비해 우수한 것으로 평가되었다.