• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.328-334
• /
• 2012

This paper proposes a design technique of wide-band antenna for handy phone with 700 MHz LTE(Long Term Evolution) low frequency bandwidth. The proposed antenna based on the PIFA(Planar Inverted-F type Antenna) structure was designed and considered. In order to realize the wide bandwidth, a round structure which is able to control the electric path length of current and a branch line element which can be obtain the dual resonance characteristics were introduced in this design. As a result, It was realized about 95 MHz bandwidth in spite of very small space of $30{\times}34mm$ used for FR-4 substrate with relative permitivity of 4.4 at 700 MHz band. Measurement results of return loss, bandwidth and gain radiation pattern were agreed well with their calculation results.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.4
• /
• pp.59-64
• /
• 2016

In this paper, a 10W GaN MMIC was designed and fabricated using the Ku-band SSPA module. For Design and fabrication of the SSPA module using Rogers(RO4003C) substrate was used for Branch-line structure. SSPA modules on budget Divider/Combiner was designed and fabricated less than the maximum insertion loss - 0.7dB. In addition, because it must be applied to the structural nature of GaN MMIC Gate Bias-Drain Bias circuit was implemented to apply the Gate-Drain sequential circuit, implemented the RF Power Detect, Temperature Detect, HPA On/Off function. Design and fabrication Ku-band SSPA Module got the measurement results that satisfy a maximum output of 15.6W, Gain 45.7dB, 19.0% efficiency.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.1
• /
• pp.144-152
• /
• 2009

This paper propose highly miniaturized active $90^{\circ}C$ phase difference power divider and combiner for application to wireless communication system. The conventional passive $90^{\circ}C$ power divider and combiner cannot be integrated on MMIC because of their very large circuit size. Therefore, the highly miniaturized active $90^{\circ}C$ phase difference power divider and combiner are required for a development of highly integrated MMIC. In this paper, the highly miniaturized active $90^{\circ}C$ phase difference power divider and combiner employing InGaAs/GaAs HBT were designed, fabricated on GaAs substrate. According to the results, the circuit size of fabricated active $90^{\circ}C$ phase difference power divider and combiner were $1.67{\times}0.87$ mm and $2.42{\times}1.05$ mm, respectively, which were 31.6% and 2.2% of the size of conventional passive branch-line coupler. The output gain division characteristic of proposed divider circuit showed 8.4 dB and 7.9 dB respectively, and output phase difference characteristic showed $-89.3^{\circ}C$. The output gain coupling characteristic of proposed combiner circuit showed 9.4 dB and 10.5 dB respectively, and output phase difference characteristic showed $-92.6^{\circ}C$. The highly miniaturized active $90^{\circ}C$ phase difference power divider and combiner exhibited good RF performances compared with the conventional passive branch-line coupler.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1281-1286
• /
• 2008

The PSK carrier signal recovery circuit using a six-port phase correlator was analyzed and the circuit structure is proposed in this paper. The proposed carrier signal recovery circuit that is made of reflection element and six-port phase correlator, which is comprised of a power divider and three hybrid branch line couplers, give a simple structure and can be fabricated without no difficulty. The circuit recovers the carrier signal of BPSK and QPSK modulation signal. The proposed scheme can be utilized as a basis structure for high-mode PSK carrier signal recovery. By simulation results, the recovered signal by the proposed circuit shows a good carrier signal characteristic with CW signal of a constant phase($23.4^{\circ}$) and ${\pm}0.8^{\circ}$ phase error due to glitch conditions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.806-812
• /
• 2009

In this paper, the omnidirectional circularly polarized(CP) antenna using arc-shaped mushroom structure with curved branch is proposed. To obtain a vertical polarization and an omnidirectional radiation pattern, the CP antenna uses zeroth-order resonance(ZOR) mode of composite right and left handed(CRLH) transmission line. The horizontal polarization is achieved by the curved branches. Also, the spacing between curved branch and arc-shaped mushroom structure gives the $90^{\circ}$ phase difference between vortical and horizontal polarization. The proposed antenna, therefore, has an omnidirectional CP radiation pattern In the azimuthal plane. The electrical size of the proposed antenna is reduced by 38%, compared with that of the previously presented omnidirectional CP antenna. In addition, the CP antenna is simply designed without $90^{\circ}$ phase shifter and dual feed line. The proposed antenna uses a Bazooka balun for good impedance matching and radiation pattern. To improve 3 dB axial ratio in XY plane, the designed antenna is optimized. After optimization, the measured 3 dB axial ratio in XY plane is observed in $86{\sim}282^{\circ}$.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.2
• /
• pp.311-318
• /
• 2002

This paper described the ultimate strength and deformation limit of welded T-joints in cold-formed square hollow sections. Previous studies showed that the strength of a T-joint still increases with increasing deformations at a ratio of branch width to chord width (${\beta}$) of below 0.8. Therefore, the strength at a certain deformation (chord flange indentation) limit can be regarded as the ultimate strength of a T-joint. The chord flange failure modes were investigated for the ratio of branch width to chord width (${\beta}$) and the ratio of chord width to chord web thickness (B/T). Experimental results including tests done by Kato proposed a deformation limit of 3%B for $16.7{\leq}B/T{\leq}41.6$ and $0.27{\leq}{\beta}{\leq}0.8$. The strength formula of CIDECT and other researchers were compared with the test results. Finally, the strength formula based on yield-line theory was proposed.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2001.11b
• /
• pp.35-42
• /
• 2001

In order to obtain basic information for pure line breeding of hemp which is effective on the pure line preservation and propagation, three varieties were investigative from 1995 to 1996 at Mokpo Experiment Station, Honam Agriculture Experiment Station, and cutting parts, cutting times, cutting length and storage duration after cutting of plant were observed. Higher rooting ratio were observed in cutting of shoot and later branch, in July 5, optimum harvesting time and 5 days after harvesting time, in shorter storage duration,0 and 2 days. Also there were the highest rooting ratio increased by from 12% to 16% in shorter cutting of 10cm than 15cm long cutting in shoot, lateral branch and stem cuttings. Hemp cv. Korea showed higher rooting ratio than the other varieties, Japan and Turkey. Therefore, it was concluded that hemp, a dioecious plant, could be effectively propagated for the pure lines by cutting method, especially in cv. Korea.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.542-550
• /
• 2001

In this paper, a channel combiner is designed to combine two adjacent digital TV channels without interference to transmit these channels with one broadband antenna. A constant impedance type combiner, consisting of two identical bandpass filters and two identical 3 dB power combiners, is chosen as a channel combiner. The bandpass filter used in the channel combiner also suppresses out-of-band signal caused by digital transmitter's non-linearity. H-plane type bandpass filters and branch-line fewer combiners are adopted in the design. The simulated results of the designed bandpass filter and power combiner show excellent agreement with the theoretical results. Finally, a channel combiner is designed by combining filters with rover combiners and the characteristics are simulated. It is shown that the designed channel combiner shows excellent performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.15-23
• /
• 2007

A simple six-port direct conversion QPSK receiver which is made up of a six-port phase correlator, a signal power detector, and I/Q channel signal de-modulator is designed and implemented in this paper. The output phase signals of six-port phase correlator are also analysed. On the basis of $90^{\circ}C$ phase relation among the six-port phase correlator output signals, the QPSK de-modulation circuit is designed by a simple circuit. The six-port phase correlator is made up of $90^{\circ}$ hybrid branch line and power detector. The six-port phase correlator, which is designed in frequency range of 11.7 to 12.0 GHz, gets the phase error characteristics less than $5^{\circ}$. By considering matching network and amplitude balance in the designed fiequency range, the designed six-port direct conversion QPSK receiver demodulates the I and Q signals with performance less than $5^{\circ}$ phase error.

• Journal of Biomedical Engineering Research
• /
• v.25 no.6
• /
• pp.537-543
• /
• 2004

In order to create three-dimensional model for human body, a method that reconstructs geometric models from contour lines on cross-section images is commonly used. We can get a set of contour lines by acquiring CT or MR images and segmenting anatomical structures. Previously proposed method divides entire contour line into simply matched regions and clefts. Since long processing time is required for reconstructing cleft regions, its performance might be degraded when manipulating complex data such as cross-sections for human body. In this paper, we propose a fast reconstruction method. It generates a triangle strip with single tiling operation for simple region that does not contain branch structures. If there exist branches in contour lines, it partitions the contour line into several sub-contours by considering the number of vertices and their spatial distribution. We implemented an automatic surface reconstruction system by using our method which reconstructs three-dimensional models for anatomical structures.