• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.607-612
• /
• 2004

Disc brake noise continues to be a major concern throughout the automotive industry despite efforts to reduce its occurrence. Eliminating vibrations during braking is an important task for both vehicle passenger comfort and reducing the overall environmental noise levels. There are several classes of disc brake noise, the major ones being squeal, judder, groan, and moan. In this study, analytical model for moan noise of rear disk brake is investigated. Modeling of the disc brake assembly to take account of the effect of different geometrical and contact parameters is studied through the use of multi-body model. The contact stiffness of the caliper and torque member plays an important role in controlling brake vibration. Therefore, a suitable material pair at the caliper/body contact has been made. An ADAMS model of a rear disc brake system was integrated with a flexible suspension trailng arm from MSC/NASTRAN. A fully non-linear dynamic simulatin of brake system behavior, containing rigid and flexible bodies, was performed for a Prescribed set of operating conditions. Simulation results were validated using data from vehicle experimental testing.

• 한국생산제조학회지
• /
• 제21권6호
• /
• pp.968-975
• /
• 2012

ABS(Anti-skid Brake System) had been developed on purpose of most effect at breaking in limited runway. An aircraft has a large amount of kinetic energy on landing. When the brakes are applied, the kinetic energy of the aircraft is dissipated as heat energy in the brake disks between the tire and the ground. The optimum value of the slip during braking is the value at the maximum coefficient of friction. An anti-skid system should maintain the brake torque at a level corresponding to this optimum value of slip. This system is electric control system for brake control valve at effective control to prevent slip and wheel speed or speed ratio. In this study we measured the thickness of the carbon disk before and after to find its wear and it shows that carbon disk brake has higher stiffness and strength than metal disk at high temperature. In addition, thermal structural stability and appropriate frictional coefficient of the carbon disk brake prove its possible substitution of metal disk brake.

• 제어로봇시스템학회논문지
• /
• 제17권4호
• /
• pp.313-320
• /
• 2011

Multi-axle driving vehicles that are used in special environments require high driving performance, steering performance, and stability. Among these vehicles, 6WS/6WD vehicles with middle wheels have structural safety by distributing the load and reducing the pitch angle during rapid acceleration and braking. 6WS/6WD vehicles are favored for military use in off road operations because of their high maneuverability and mobility on extreme terrains and obstacles. 6WD vehicles that using in-wheel motor can generate the independent wheel torque without other mechanical parts. Conventional vehicles, however, cannot generate an opposite driving force at each side wheel. Using an independent steering and driving system, six-wheel vehicles can show better performance than conventional vehicles. Using of independent steering and driving system, the 6 wheel vehicle can improve a performance better than conventional vehicle. This vehicle enhances the maneuverability under low speed and the stability at high speed. This paper describes an independent 6WS/6WD vehicle, consists of three parts; Vehicle Model, Control Algorithm for 6WS/6WD and Simulation. First, vehicle model is application of TruckSim software for 6WS and 6WD. Second, control algorithm describes the optimum tire force distribution method in view of energy saving. Last is simulation and verification.

• Journal of Magnetics
• /
• 제22권1호
• /
• pp.23-28
• /
• 2017

This paper is a study of the eddy current brake designed to replace the air brake of railway application. The eddy current brake has the advantage of being able to take a high current density compared to the other application because this brake is used for applying brakes to the rolling stock for a shorter amount of time. Also, this braking system has the merit of being able to take a high current density at low speed rather than at high speed, because the heat generated by the low speed operation is less than that of the high speed operation. This paper also presents a method of improving the output torque of the eddy current brake at low speed operation through a change of the winding as well as the basic design.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.302-304
• /
• 1996

In this paper, a new algorithm for sensorless speed control of switched reluctance motor (SRM) is proposed. It is based on the measurement of initial rate of change of phase current. The initial rate of rise of phase current mainly depends up on the phase inductance at the time instant when the phase is excited. Therefore, the measurement of initial di/dt permits rotor position estimation, which is used to trigger the next phase. In the proposed technique, there is no need to generate additional current pulses when a phase is not excited. Therefore, this scheme does not introduce the unwanted braking torque. Also, only one current measurement is made every time a phase is excited. This reduces the computational load on the micro-controller and enhances the speed range of the sensorless drive. By using this scheme it is possible to implement the sensorless control of SRM using low cost micro-controller.

• 전기학회논문지
• /
• 제63권1호
• /
• pp.184-190
• /
• 2014

Fuel cell power system, unlike conventional energy sources, converts chemical energy into electrical energy through electrochemical reaction of hydrogen and oxygen. In recent years, railway field as well as mobile fuel cell power system is being studying actively with development of hydrogen storage technologies. This paper presents the feasibility study on small-scale prototype electric railway vehicle application using fuel cell generation system. it is confirmed that proposed fuelcell-battery hybrid system shows good response characteristic about speed and torque based on design of parameter on system. Also as results of response for proposed system modeling, it show that powering mode and braking mode of system is controlled by switching devices of converters.

• 대한기계학회논문집A
• /
• 제40권12호
• /
• pp.1067-1076
• /
• 2016

본 논문은 고령자를 위한 하이브리형 전동 휠체어의 개발에 대해서 서술하였다. 개발된 하이브리드형 휠체어는 기존 전동 휠체어에 비해 기구적 및 제어적 특징을 가지고 있다. 기구적 특징으로써 인체공학적 등받이 브레이크 메커니즘을 새롭게 고안하였고, 이로부터 고령자들이 몸동작을 이용하여 손쉽게 제동을 할 수 있도록 하였다. 제어적 특징으로써, 휠 토크 보조, 마찰/관성보상, 중력보상 및 한 손 구동과 같은 다양한 동력보조 기능을 융합하여 고령 탑승자의 근력 부담을 현격히 감소시켰다. 휠 토크의 보조를 위해 핸드림에 스트레인게이지를 부착하여 탑승자가 가하는 휠 토크를 측정하였으며, 마찰보상과 관성보상을 위해 바퀴와 시트에 각각 자이로스코프와 가속도센서를 부착하였다. 또한, 중력보상을 위해 기울기 센서를 추가적으로 부착하였으며, 편마비 환자들과 같이 한 손 만을 사용할 수 있는 사용자들 위해서 시트 밑면에 부착된 압력 센서로부터 휠체어의 주행 방향을 인식하고 자이로스코프를 이용하여 반대편 휠의 각속도를 제어하는 한 손 주행 알고리즘을 새롭게 고안하였다. 최종적으로 본 연구에서 고안한 운동 보조 알고리즘의 성능을 각종 실험으로부터 검증하였다.

• 한국산학기술학회논문지
• /
• 제21권10호
• /
• pp.581-588
• /
• 2020

본 논문은 전기기계식제동장치(EMB : Electro Mechanical Brake, 이하 EMB)의 제동패드 마모발생에 따른 소프트웨어 기반의 마모보상방법의 적용 및 성능평가를 다루었다. EMB의 구동을 위해 사용된 모터는 3상 매입형 영구자석 동기전동기(IPMSM : Interior Permanent Magnet Synchronous Motor, 이하 IPMSM)가 사용되었다. EMB의 압부력(clamping force) 제어를 위해 위치제어기, 속도제어기 및 전류제어기가 적용되었으며, IPMSM의 출력 압부력 예측을 위해 모터의 거리별 압부력 실험을 통하여 힘 추정기(force estimator)를 1차 모델식으로 단순화 하였다. 제동패드에서 마모가 발생함에 따라 IPMSM에서 출력되는 토크전류의 크기가 감소하는 특성을 이용하여 기준 토크전류와의 비교를 통해 힘 추정기를 업데이트하는 방법으로 마모보상이 가능함을 보였다. 제동패드의 마모 후 최대 압부력 도달시간이 0.1초 이내로 증가하였으나, 마모패드 장착시에도 제동압부력은 마모 전 제동패드와 동일한 최대 기준 압부력을 만족하였으며, 최대압부력 도달시간의 경우 0.5초(기준값) 이내임을 실험으로 검증하였다. 소프트웨어 기반의 EMB 제동패드의 마모보상 방법은 철도차량의 출발 전 제동장치 점검시 테스트모드의 진입을 통하여 수행이 가능하다.

• 전력전자학회논문지
• /
• 제17권2호
• /
• pp.166-173
• /
• 2012

Plug-in Hybrid Electric Vehicle is driven by the engine, the primary traction motor, and the secondary auxiliary motor generating the electric power for battery charging. Secondary auxiliary motor should be connected to the engine or separated from the engine by the clutch system. This paper presents the position controller of the BLDC motor for the clutch system of Plug-in Hybrid Electric Vehicle. The BLDC motor can be applied to the clutch system in spite of it's low accuracy of the position control due to high gear ratio between the clutch and the motor. Since the attachment and the detachment between the motor and the engine should be carried out within 0.3 seconds, the position controller with fast acceleration and deceleration is implemented. For the torque control with braking operation for the BLDC motor, the modified bipolar PWM method with low current ripple compared to the conventional unipolar PWM is presented. The position control performance of the BLDC motor for the clutch system is verified through the simulation and experiments.

• 한국해양공학회지
• /
• 제23권4호
• /
• pp.69-77
• /
• 2009

Structural analysis of a brake shoe for commercial vehicle was performed using finite element method. Since the strength of a brake shoe is affected by the magnitude and distribution shape of the contact pressure with the drum, the contact pressure between the shoe friction material and drum was calculated using a 2-Dimensional non-linear contact analysis in a state. And the brake was actuated by input air pressure and the drum of it was calculated both stationary and dynamic based on forced torque applied to the drum during the static state analysis. The results of the above analysis were then used as the load boundary conditions for a 3-Dimensional shoe model analysis to determine the maximum strain on the shoes. In the analysis model, the values of tensile test were used for the material properties of the brake shoes and drum, while the values of compression test were used for the friction material. We assumed it as linear variation, even though the properties of friction material were actually non-linear. The experiments were carried out under the same analysis conditions used for fatigue test and under the same brake system which equipped with a brake drum based on the actual axle state in a vehicle. The strains were measured at the same locations where the analysis was performed on the shoes. The obtained results of the experiment matched well with those from the analysis. Consequently, the model used in this study was able to determine the stress at the maximum air pressure at the braking system, thereby a modified shoe model in facilitating was satisfied with the required endurance strength in the vehicle.