차량의 제동장치는 제동시 차량의 조향안정성을 유지하면서 최소한의 제동거리를 확보하는 장 치라 할 수 있다. 제동시 차량의 조향안정성 유지와 최소제동거리를 확보하기 위해서는 차량의 적절한 제동능력에 필요한 전제동토오크를 전후륜의 제동장치에 적당하게 배분시켜야 한다. 그러나 차량의 각차륜의 하중 상태는 여러 가지 적재상태와 제동시중량이동 등에 따라 변하게 되므로 고정된 제동장치로서는 전후륜의 제동토오크를 가변시킬 수 없어 설계시 빈도가 높은 조건에 맞추어 제동장치의 구성부품을 확정할 수밖에 없다. 차량에 따라서는 축하중상태의 변 화가 큰 경우와 공용화를 위하여 여러 모델의 차량에 동일제동 장치를 적용하려고 할 경우에 문제점이 따르기 마련이다. 본고에서는 제동장치의 전후륜의 제동토오크 배분에 대하여 고찰하여 설계개념을 파악하고자 한다.
The essence of ABS(Anti-skid Brake System) control is to continuously adjust brake pressure to maintain optimum brake torque. This optimum level should balance tire and runway friction its peak value, yielding maximum braking deceleration. It influences not only the deceleration and the taxing distance of an aircraft, but also the strength and the fatigue life of the landing gear. In this paper, an ABS control algorithm is developed with a dynamics model of 5-DOFD(Degree of Freedom). The algorithm is verified by simulations and the simulation results are presented. The dynamics model is simulated by the computer.
Recently, many types of electric vehicles including a heavy duty vehicle have been developed and released because of the better fuel economy and less gas products. In this study, research about an electric bus which utilizes the wheel motor drive system was conducted. The wheel motor is a motor connected to the wheel directly only with a simple gear so that the developer can utilize the space efficiently and the whole system efficiency will be better because of simple structure. However, because it is different from former types of vehicles which use the differential gear, the development of the integrated control logic is required in order to meet the vehicle stability and driving performance. The developed control logic is composed with direct yaw moment control, regenerative braking control and slip control logics. It is compared to the control logics which does not consist of direct yaw moment control and slip control when the vehicle is exposed in tough situations. For the unification of the control logic, a few maps were developed and applied to determine the output torque of each motor according to the driving status. As a result, it is shown that the developed control logic is more safe and well follow the target speed than the other control logic applied simulations.
브레이크 동력계는 브레이크의 성능을 시험하는 장치로 시험구역, 기계적 관성구역, 전기모터 및 제어구역으로 구성된다. 혼성동력계는 기계적 관성 구역의 크기를 줄이고 전기모터를 이용하여 브레이크 작동에 따른 기계적 관성의 손실을 보상하는 방식으로 상대적으로 작은 기계적 관성 크기와 적은 비용으로 시험이 가능한 장점이 있다. 본 논문에서는 공간적 제약이 있는 실험실에 적절한 혼성동력계를 설계하였고, 설계된 혼성동력계에서 마찰계수 변화 등 주요 설계변수가 혼성동력계 제동성능에 미치는 영향을 분석하였다. 본 연구를 통해 축소된 기계적 관성에 의한 에너지 손실을 보상하기 위한 전기 모터의 토크를 측정하면 마찰재의 불량여부를 판단 할 수 있는 결과를 얻었다.
To meet the increasing demand from various fishing fields for training of fishing equipment operators, a fishing winch simulator was designed to train maritime students in the correct and safe operation of hydraulic winches under various load conditions related to fishing operations. The aim of this study is to describe the basic dynamic characteristics of the newly developed hydraulic fishing winch simulator and particularly to analyze the mechanical responses produced on the winch operation controls. The winch simulator consists of two winch units, a computer control and data acquisition system, a control consol and other associated mechanisms. When one winch is in hauling mode, the other one will always be in loading mode. The revolution speed of the hauling winch was controlled by a proportional directional control valve, and the braking torque of the loading winch was controlled by a proportional pressure control valve. The simulation experiments indicated that the dynamic characteristics of the hauling winch followed the braking response characteristics of the loading winch. The tests also showed that the warp speed and tension linearly depend on the pressure differential across the motor of the loading winch controlled by operating the proportional pressure control valve during the hauling operation. The experience gained from various training courses showed that the fishing winch simulator was very realistic and it was valuable for training novice winch operators. The results of the winch simulation exercise were recorded and used to evaluate the training on the operation and handling of the winch system. From these test results, we concluded that the tension acting on the warp during hauling operations can successfully be simulated by controlling the pressure differential across the motor with step changes of the control input signal to the proportional pressure control valve of the loading winch.
최근 자동차는 안전성, 편리성, 친환경 등의 목적으로 개발되고 있다. 특히, 자동차 안전성에 대한 인식이 중요하게 바뀌고 있다. 이에 따라, ADAS 개발로 인한 안전 시스템들이 등장하였다. 그러나 ADAS의 개발과 시험 평가를 통해 양산 되는 기간은 상당히 오래 걸린다. 따라서 본 논문에서는 ADAS 개발과 시험 평가에 필요한 기간을 단축시키기 위해 브레이크 다이나모미터를 개발 하였다. 또한 개발한 브레이크 다이나모미터는 국제 표준인 JIS D-0210을 만족하며, ADAS의 모드별로 사용자가 시험 조건과 시험 방법을 선택 하여 제동력을 평가할 수 있다. 그리고 개발하는 브레이크 다이나모미터의 신뢰성 검증을 위해 선행 연구에서 제안한 ACC, LKAS, AEB의 시나리오를 사용하였다. 개발한 브레이크 다이나모미터는 시험값과 선행 연구를 통해 제안된 ADAS 모드별 이론식에 의한 계산값을 비교하여 신뢰성을 검증하였다. 또한, 향후에는 ADAS의 실차시험이 불가능한 환경에서 ADAS 모드별 브레이크 부품의 성능 평가가 가능할 것으로 기대 된다.
Wet clutches in an automatic transmission enable the transmission of the engine power by the frictional torque experienced and noted between disk and plates. Since the clutch frictional torque considerably affects the shift quality of an automatic transmission as well as the durability of the machinery, its friction characteristics must be carefully examined to meet the design requirements. The SAE No. 2 friction test machine is a well-known standard to evaluate mainly the friction characteristics of plate clutches along with the required automatic transmission fluids. This paper reviews the experimental analysis of the wet clutch friction characteristics by using the exclusively developed clutch test machine which is capable of controlling the clutch test procedure, in accordance with the applicable test standard and processing of the experimental data automatically. As the clutch test machine is designed for the accommodation of dual clutches which is applied to the real transmission, it can evaluate not only the clutch friction characteristics, but also an actuation performance of a measured clutch piston. In respect to friction characteristics involving dynamic friction coefficients, the energy absorbed in a clutch disk and the recorded temperatures of clutch plates during braking actions and procedures are also investigated. Additionally, the change of friction coefficients by the use of the repeated clutch application is also observed with the endurance test functions of an accurately calibrated and dedicated clutch test machine.
This study was conducted to develop a dry paddy seeder of strip tillage. The prototype is 8 rows drill seeder, which is composed of a strip tillage, sowing and fertilizing device, and pressing wheels to do the strip tillage, sowing, fertilizing, and draining ditch, simultaneously. The performances of prototype was evaluated through the investigation of fuel consumption, tillage torque, ratio of soil breaking, and economical efficiency and the results were compared with these of a dry paddy seeder that needs whole tillage. According to the USDA textural classification, the experiment field was composed of sandy loam which consisted of 56.8 of sand, 30.2 of silt and 13.0 % of clay, respectively. Its hardness ranged from 952 to 1,673 kPa depending on the soil depth, and its soil moisture content was 24.9%(d. b.) Fuel consumption of the prototype was 5,015g/hr at 2,000 rpm of engine, which was consequently 64% smaller than that of the conventional dry paddy seeder. For the tillage torque, it ranged from 132 to 206N$.$m depending on the tillage pitch, which was 10∼30% smaller than that of the conventional dry paddy seeder. The ratio of soil braking of the prototype was 87∼98%, whereas that of the conventional dry paddy seeder was 80∼97%. The working performance of the prototype was surveyed to be 3.8hours/ha, which was about 5 times higher than that of the conventional dry paddy seeder. The cost reduction of 26.3% was obtained by using the prototype.
This paper deals with experimental evaluation methods for high speed judder on the brake-caliper system. Firstly, two types of brake caliper systems due to the wheel vibration was evaluated. Secondly, the high-speed judder of the brake was also investigated using the subjective rating evaluation in the high-speed road test. These experimental evaluations were carried out by changing the materials of brake pad and the specifications of the brake-corner module. Based upon the test results, a new specification of the brake pad, $15{\times}5$ vertical chamfer, was proposed. The new brake pad showed 3 points, 60 %, improvement in the subjective-rating evaluation comparing with conventional one. Besides, we need to decide properly with judder characteristic of pad material and have to carefully take into consideration other design parameters; caliper, disc, and the braking performance, durability, squeal noise.
The transmission of tracked vehicles performs complex functions as steering, shifting, braking, etc. and the system level life time has been a key influenced by the number of sub-parts like as gear assembly, torque converter, clutches, bearings and so on. In particular, the mechanical type steering system in tracked vehicle has impact shock torques in steering shift and those kind of shock torques can effect on the durability of many sub-parts in power train system. The field failure modes of gear assembly, steering assembly and the bearings of output shaft appear as a very complex phenomenon. In this study, the actual failure, which may occur in field, of the transmission was investigated comprehensively and that the endurance test on the resulting output shaft bearing failure analysis and life assessment was performed. Life time test method used in this study, developed for the purpose of the internal usage, and under these testing techniques the impact of the each bearing damage, which used in tracked vehicle transmission left / right outputs of different structures, was analyzed.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.