• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.5 s.98
• /
• pp.83-90
• /
• 1999

The prevalence of microprocessor-based controllers in automotive system has greatly increased the need for tools which can be used to validate and test control system over their full range of operation. The objective of this paper is to develop a real time simulator of an anti-lock braking system and traction control system by the methodology of using hardware-in-the-loop simulation based on a personal computer. By use of this simulator, the analyses of commercial electronic control units and components for ABS/TCS were performed successfully. The simulator of this research can be applied to development of more advanced control system(such as vehicle dynamic control system) and other automotive system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.213-218
• /
• 2006

Hot spot phenomenon is caused by non-uniform contact area between brake pad and disk frequent braking. Brake disk deformed by locally concentrated heat increases magnitude of frictional vibration. And this deformation can highly influence the judder vibration. In this experimental study, vibration and hot spot was measured in accordance with rotation of disk and pressure of master cylinder for finding the factors that causes hot spot phenomena. For comparing hot spot aspects with mode shapes of disk, mode shapes were measured by conducting modal test, and analyzed by using finite element analysis. Relation between hot spot phenomenon, and mode shape, pressure of master cylinder and rotation speed of disk respectively, was achieved by hot spot measurement and frequency analysis.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.110-115
• /
• 1999

Experimental study is conducted to clarify the pneumatic characteristics of brake system for freight car. KNR(Korean National Railroad)'s freight cars have the laden-tare type control valve of brake system. But, laden-tare type control valve has some shortcomings to match the high speed freight car. Newly developed diaphragm type control valve is introduced to adopt freight car for speed-up. The test using the formated train set consisted of 21 cars is conducted to estimate the pneumatic braking efficiency of the mixed train set. From the results of experiment, the pressure characteristics of each brake cylinder show similar patterns qualitatively. But, in the case of release and brake application, quantitative pressure values of brake cylinder are different.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.930-939
• /
• 2009

A bimodal tram is being developed to combine the flexibility of a bus with the punctuality of a train. The propulsion system is a series hybrid type using a set of CNG engine generator and Li-polymer battery. This paper presents the experimental results of the series hybrid propulsion power unit using an active loader which can simulate powering and regenerative braking conditions of the propulsion equipments continuously. The power sharing scheme between PWM converter and a battery pack has been observed. The measurement results of DC link voltage and SOC(State Of Charge) of battery pack are presented.

• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.330-332
• /
• 1997

In this paper, a development of the 7.2kV class $SF_6$ gas electromagnetic contactor which is used a rotary-arc principle in interrupting method is presented. A prototype contactor is made. In the interrupting small current permanent-magnet is used and in the interrupting high current the coil through which arc current itself flows is used. Successfully the prototype contactor carrys out the making, the braking and short time test.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.725-730
• /
• 1998

Recently, non-destructive tests are getting popular in evaluating concrete properties without braking specimens. Among several NDT methods, P-wave velocity measurement technique has been widely used to evaluate the stiffness and strength of concrete. The purpose of this study is to investigate factors influencing P-wave velocity measured by impact-resonant method and ultrasonic pulse velocity method, such as moisture content of concrete, existence and size of coarse aggregates, sensor and sampling rate. Test results show that rod-wave velocity measured by impact-resonant method and ultrasonic pulse velocity are significantly affected by the moisture content of concrete, i.e., the lower moisture content, the lower velocity. Moisture content influences rod-wave velocity stronger than ultrasonic pulse velocity. Rod-wave velocity is faster in concrete than in mortar and is also faster in concrete containing small size aggregates. Sensor and sampling rate have little influence on velocity.

• International Journal of Automotive Technology
• /
• v.6 no.5
• /
• pp.537-544
• /
• 2005

This paper presents the efficiency measurement and energy analysis for a parallel HEY. Using the HEV test rig, the efficiency of each powertrain component is measured for a given driving cycle including the regenerative braking system. Accompanied by the efficiency measurements, a detailed energy analysis is performed. Based on the efficiency measurement and energy analysis, a HEV performance simulator is developed. Using the simulator, the HEV performance is evaluated for a mild hybrid system. It is expected that the HEV simulator developed can be used to obtain further optimization potentials.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.05a
• /
• pp.297-300
• /
• 2009

Recently, TTX(Tilting Train eXpress), EMU (Electric Multiple Unit) has operated test. Presently, electric problems(harmonic, voltage variation etc) of TTX are studying briskly. Henceforth, electrical harmonic study of TTX will operate on the rail actually is needed. In this paper, we detected electrical harmonic of operating TTX. In addition to we analyzed and estimated electrical harmonic regarding TTX's coasting, acceleration and braking state.

• Tribology and Lubricants
• /
• v.13 no.3
• /
• pp.10-19
• /
• 1997

Frictional characteristics of two different types of automotive friction materials were studied. They were non-asbestos organic and semi-metallic friction materials. The two friction materials were tested using an inertial brake dynamometer to investigate friction stability, rooster tailing phenomena, temperature change during drags and stops. Results show that the level of the friction force is strong functions of time, temperature, and speed regardless of the type of friction materials. In particular, rooster tailing effects are pronounced in the case of semi-metallic friction materials compared to non-asbestos organic friction materials. The phenomena appear strongly dependent on raw materials contained in the friction materials.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.8 s.113
• /
• pp.886-892
• /
• 2006

Hot spot phenomenon is caused by non-uniform contact area between brake pad and disk frequent braking. Brake disk deformed by locally concentrated heat increases magnitude of frictional vibration. And this deformation can highly influence the judder vibration. In this experimental study, vibration and hot spot was measured in accordance with rotation of disk and pressure of master cylinder for finding the factors that causes hot spot phenomena. For comparing hot spot aspects with mode shapes of disk, mode shapes were measured by conducting modal test, and analyzed by using finite element analysis. Relation between hot spot phenomenon, and mode shape, pressure of master cylinder and rotation speed of disk respectively, was achieved by hot spot measurement and frequency analysis.