• 한국자동차공학회논문집
• /
• 제21권1호
• /
• pp.61-67
• /
• 2013

In this paper, it was studied how the critical speed which could occur hot judder due to disk temperature. Through the dynamometer experiment, we measured the critical velocity and surface temperature when the hot judder occur on the disk break. Also with the critical velocity theory equation and the temperature change graph of factors which used in the equation, we was induced experiment equation including theory equation and experiment values. And it has compared with the method which approach as linea. From this, we predicted the change of critical speed which could occur hot judder due to disk temperature. In addition, critical speed graph has compared with actual driving speed and disc temperature at a vehicle test. Therefore it was estimate to possibility of arising hot judder.

• 오토저널
• /
• 제10권6호
• /
• pp.72-84
• /
• 1988

Engine performance is one of the main objectives specified at the beginning of a new engine design project. The cycle simulation for SI engine is based on the zero-dimensional gas exchange model and a heat release expression by Viebe. This program also requires minimum input data and takes only a short time to run. Heat transfer from cylinder transfer formula. The flow coefficient (effective area) is calculated from valve lift using the standard flow coefficient curve and engine friction is calculated from the Millington and Hartles' engine friction formula. The chemical species considered in burned gas are 6 species CO, CO, H$_{2}$, H$_{2}$O, $O_{2}$, N$_{2}$ and the cylinder pressure, homogeneous cylinder temperature, gas composition and burned fraction are calculated at each crank angle through the cycle. To check the validity and accuracy, experimental study was done with 3 engines for measuring cylinder pressure, indicated mean effective pressure, brake mean effective pressure and air flow rate, etc. Despite its simple assumptions, cycle simulation showes excellent breathing and performance correlation when compared with data of tested engines, and have been proved useful in engine design.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권1호
• /
• pp.195-211
• /
• 2015

Flat plate friction lines have been used in the process to estimate speed performance of full-scale ships in model tests. The results of the previous studies showed considerable differences in determining form factors depending on changes in plate friction lines and Reynolds numbers. These differences had a great influence on estimation of speed performance of full-scale ships. This study was conducted in two parts. In the first part, the scale effect of the form factor depending on change in the Reynolds number was studied based on CFD, in connection with three kinds of friction resistance curves: the ITTC-1957, the curve proposed by Grigson (1993; 1996), and the curve developed by Katsui et al. (2005). In the second part, change in the form factor by three kinds of friction resistance curves was investtigated based on model tests, and then the brake power and the revolution that were finally determined by expansion processes of full-scale ships. When three kinds of friction resistance curves were applied to each kind of ships, these were investigated: differences between resistance and self-propulsion components induced in the expansion processes of full-scale ships, correlation of effects between these components, and tendency of each kind of ships. Finally, what friction resistance curve was well consistent with results of test operation was examined per each kind of ships.

• 한국지능시스템학회논문지
• /
• 제24권1호
• /
• pp.33-39
• /
• 2014

자동 주행 차량을 구현하기 위해서는 장애물 인식, 차선 인식 및 변경 등 많은 기능들이 필요하다. 본 논문에서는 자동차 주행에 필요한 '차선 인식'의 범위를 확장시킨 '색깔 인식' 개념을 도입 적용시키기 위해 3가지 코스를 주행하는 시스템을 구현하였다. RC car의 크기와 비례하게 축소 제작한 각 코스에서 주행에 필요한 검지선의 위치, 기울기 및 차량의 속도를 고려하여 조향 제어를 하였고, 브레이크 기능이 없는 RC car를 제어하기 위해 차량의 속도와 검지선의 위치를 고려하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.405-410
• /
• 2004

There are two types of noises in running the rail vehicle. The one is periodic by electric motors, dehumidifiers, and dusting machines. And the other is aperiodic squeal noise by the frictions between the wheels and the rail or the disks and pads. The periodic noises in rail vehicle have been reduced by changing DC motors to AC motors with silencers, and by improving the lubricants. However, almost nothing relating a periodic noise has been studied. In this paper, the experimental methods were applied to understand phenomena of the squeal noise, which was occurred by the friction variation due to aperiodic stick and slip with low repeatability in the process of dry friction of the disk and the pad when a rail vehicle was being braked. By the experimental acoustic test, it was found the specific frequencies relating the squeal noise. And by modal testing, it was measured the resonant frequencies in the disk and the pad-plate which were the components of the braking system, and in the whole braking system, and it was found the specific frequencies having the effects on the squeal noise.

• 한국공간구조학회논문집
• /
• 제4권1호
• /
• pp.77-86
• /
• 2004

시공시 콘크리트의 하중은 받는 데크플레이트의 지지능력은 압축부분 플랜지에서 좌굴에 의해서 결정되어 진다. 얇은 철판 데크플레이트의 압축플랜지에서 중간스티프너의 크기와 위치는 플랜지의 좌굴모드에 강한 영향을 발휘한다. 높은 강도 철판으로 구성된 시험체 단면은 다양한 좌굴모드를 유도하기 위하여 작은 것에서 큰 스티프너에 걸쳐 압축플랜지에 만들어 졌다. ABAQUS 프로그램 해석은 좌굴모드를 지배하는 중간스티프너의 효과를 결정하기 위하여 수행되었다. 각 실험체 시리즈는 단순보로 순수휨이 적용되었다. 실험결과 소성파괴 메카니즘을 통하여 극한파괴에 앞서 다양한 좌굴형상이 나타났다. 실험으로 결정되어진 좌굴응력은 ABAQUS해석으로 얻어진 해석결과와 각국의 규준값들과 비교하기 위하여 사용되었다.

• 한국기계가공학회지
• /
• 제13권6호
• /
• pp.61-65
• /
• 2014

Construction heat insulating material for construction is used in large amounts in industry. In the manufacturing process of this insulation material, a thermal insulation material is completed while a polymer in a liquid state passes through Hall breaker. At this time, the quality and form of a product are determined by a hole in the breaker according to the oil pressure of the fluid and the change of the flow velocity. The friction wear action with regard to partner movement between the two levels of quality of materials affects the performance and the lifetimes of machine parts. In this study of a friction test, SM45C, which is a material used to create brake holes, was used. PVC was used to create the specimen. Moreover, an experiment divided a lubricous state and an unlubricated condition. The resulting value over the load of a pin, the revolving speed of a disk, and the standby state of an experimental result disk could be acquired.

• 한국자동차공학회논문집
• /
• 제11권5호
• /
• pp.112-118
• /
• 2003

The friction coefficients of the rubber for clutch master cylinder were experimentally measured in this study. The cylindrical rubber samples for primary cup-seal and secondary cup-seal were tested against the aluminum or the steel plates of master cylinder housing under the various conditions of brake oil temperatures and normal loads. Dry sliding friction coefficients were also measured under various load conditions. The test revealed following results. First, the friction coefficient under fluid lubrication condition in general decreases, as the oil temperature or normal load increases. Second, the steel plate of low surface roughness yielded comparatively low friction coefficient on the range of 0.30∼0.67. On the other hand, the aluminum plate of high surface roughness yielded high friction coefficient on the range of 0.31∼1.15. Third, the friction coefficient of dry surface contact decreases as the normal load increases. This is contrary to the general principle of friction coefficient between metal plates.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.72-80
• /
• 2013

This study is to develop and evaluate an AFS and an ARS controllers to enhance lateral stability of a vehicle. A sliding mode control (SMC) and a fuzzy logic control (FLC) methods are applied to calculate the desired additional steering angle of AFS equipped vehicle or desired rear steer angle of ARS equipped vehicle. To validate AFS and ARS systems, an eight degree of freedom, nonlinear vehicle model and an ABS controllers are also used. Several road conditions are used to test the performances. The results showed that the yaw rate of the AFS and the ARS vehicle followed the reference yaw rate very well within the adhesion limit. However, the AFS improves the lateral stability near the limit compared with the ARS. Because the SMC and the FLC show similar vehicle responses, performance discrimination is small. On split-${\mu}$ road, the AFS and the ARS vehicle had enhanced the lateral stability.

• 한국산학기술학회논문지
• /
• 제12권4호
• /
• pp.1547-1551
• /
• 2011

기화기 방식의 엔진을 EFI 소형 엔진으로 설계 변경하여 제작하였다. 최적의 작동 조건을 선정하기위하여 엔진의 성능개발을 수행하였다. EFI 엔진의 최대 출력 및 최대 토크는 12.56Ps 및 25.4Nm로 기화기 엔진과 동등한 수준이다. EFI 소형엔진의 연료 소모율은 기화기 방식 엔진 대비 평균 17% 향상되었다. KG2-6모드 실험을 통한 HC+NOx는 7.46g/kWh로 측정되어, EPA Phase 3 규제를 만족하였다. THC는 기화기식 엔진 대비 평균 41% 저감되었으나, 열효율의 상승으로 인하여 NOx는 평균 3.5배 증가하였다.