• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.3
• /
• pp.225-230
• /
• 2016

Fiber Bragg grating (FBG) sensors are currently the most prevalent sensors because of their unique advantages such as ease of multiplexing and capability of performing absolute measurements. They are applied to various structures for structural health monitoring (SHM). The signal characteristics of FBG sensors under thermal loading should be investigated to enhance the reliability of these sensors, because they are exposed to certain cyclic thermal loads due to temperature changes resulting from change of seasons, when they are applied to structures for SHM. In this study, tests on specimens are conducted in a thermal chamber with temperature changes from -$20^{\circ}C$ to $60^{\circ}C$ for 300 cycles. For the specimens, two types of base materials and adhesives that are normally used in the manufacture of packaged FBG sensors are selected. From the test results, it is confirmed that the FBG sensors undergo some degree of compressive strain under cyclic thermal load; this can lead to measurement errors. Hence, a pre-calibration is necessary before applying these sensors to structures for long-term SHM.

• Journal of Sensor Science and Technology
• /
• v.30 no.4
• /
• pp.250-254
• /
• 2021

A highly sensitive and selective non-dispersive infrared (NDIR) carbon dioxide gas sensor requires achieving high transmittance and narrow full width at half maximum (FWHM), which depends on the interface of the optical filter for precise measurement of carbon dioxide concentration. This paper presents the design, simulation, and fabrication of a Fabry-Perot filter based on a distributed Bragg reflector (DBR) for a low-cost NDIR carbon dioxide sensor. The Fabry-Perot filter consists of upper and lower DBR pairs, which comprise multilayered stacks of alternating high- and low-index thin films, and a cavity layer for the resonance of incident light. As the number of DBR pairs inside the reflector increases, the FWHM of the transmitted light becomes narrower, but the transmittance of light decreases substantially. Therefore, it is essential to analyze the relationship between the FWHM and transmittance according to the number of DBR pairs. The DBR is made of silicon and silicon dioxide by RF magnetron sputtering on a glass wafer. After the optimal conditions based on simulation results were realized, the DBR exhibited a light transmittance of 38.5% at 4.26 ㎛ and an FWHM of 158 nm. The improved results substantiate the advantages of the low-cost and minimized process compared to expensive commercial filters.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.605-609
• /
• 2006

In this study, two kinds of smart accelerometers are investigated for the application of smart sensors to the structural health monitoring of infrastructures. Smart optical Fiber Bragg Grating (FBG) type and Micro-Electo-Mechanical System (MEMS) type accelerometers are selected for this study and the high sensitive ICP type accelerometer is used for the reference sensor. Small size shaking table tests were performed with 3-story shear building model using random input ground motions. The output only modal identification was carried out using stochastic subspace identification and the performances of sensors are compared in modal domain indirectly. The modal sensitivity method was applied to update the story stiffness of numerical model and the updated results were verified using the additional experiments for the same structure with additional mass.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.257-264
• /
• 2010

Generally, estimations on the displacement as an important factor in evaluating the safety of large structures could be a barometer assessing whether the condition of the structure is deteriorating. Practically, it is not easy how to measure the displacement response to large structures like suspension bridges. In this study, as a method for estimation displacement response from strain signals, mode decomposition technique is proposed. Total displacement response is estimated by superposing quasistatic displacement response and modal displacement responses in dominant modes with larger contributions after estimating the modal displacement responses. If foiled strain gauges are used to measure strain signals, there would likely to generate electric noise, what's more, the more measuring points there are the more economic burden it could be. In order to solve such problems, fiber optic bragg-grating(FBG) sensors were used, which have multi-point measurements with no effect on electric noises. Therefore, the experiment was performed through dynamic load test of suspension bridge and plate-girder bridge to review the possibility for using mode decomposition technique.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.83-87
• /
• 2022

Recently, as the thickness of the semiconductor package becomes thinner, warpage has become a major issue. Since the warpage is caused by differences in material properties between package components, it is essential to precisely evaluate the material properties of the EMC(Epoxy molding compound), one of the main components, to predict the warpage accurately. Especially, the cure shrinkage of the EMC is generated during the curing process, and among them, the effective cure shrinkage that occurs after the gelation point is a key factor in warpage. In this study, the gelation point of the EMC was defined from the dissipation factor measured using the dielectric sensor during the curing process similar with actual semiconductor package. In addition, DSC (Differential scanning calorimetry) test and rheometer test were conducted to analyze the dielectrometry measurement. As a result, the dielectrometry was verified to be an effective method for monitoring the curing status of the EMC. Simultaneously, the strain transition of the EMC during the curing process was measured using the FBG (Fiber Bragg grating) sensor. From these results, the effective cure shrinkage of the EMC during the curing process was measured.

• Journal of information and communication convergence engineering
• /
• v.4 no.4
• /
• pp.155-157
• /
• 2006

This paper presents the thermal technique to improve characteristic of planar spiral inductors. The spiral inductors were fabricated on silicon dioxide/silicon (SiO2/Si) wafer. The thermal treatment was done by annealing processes. The measure results showed a considerable improvement of return loss (Sl1). This thermal treatment seems very promising for enhancing spiral inductors based RF IC's.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.04a
• /
• pp.37-39
• /
• 2008

The purpose of this study is to improve the defects of DPP fabric by heat setting and to describe the change of physical properties of DPP fabrics. The thermosetting was carried out in autoclave from 100 to 140$^{\circ}C$ temperature range for 10min.. In this study, we investigated the effect of the thermosetting temperatures on the structural, thermal, mechanical properties and dyeability of DPP fabrics. The melting peak of multi peak changed to single peak with an increased thermosetting temperatures. The melting energy(J/g), the tensile strength and elongation were found to increase with increasing temperature of heat setting. The diffraction peak at Bragg angle(2${\theta}$) about 13.8$^{\circ}$ were very strong, and diffraction intensity, d-spacing and half-width decreased with increasing thermosetting temperatures. On the other hand, the dyeability(K/S) and crease recovery decreased with an increasing thermosetting temperatures.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.114-118
• /
• 2009

이 논문에서는 울돌목 시험조류발전소에 구축 중인 구조건전성 감시시스템의 계획, 설치 및 활용에 대하여 소개하였다. 현재 시험조류발전소에 설치된 센서로는 전기저항식 변형률계, 광섬유 FBG(Fiber Bragg Grating) 센서, 압전형 MFC(Macro Fiber Composite) 센서, 2축 경사계, 서보형 가속도계 등과 같은 지지구조물의 구조거동을 감시하기 위한 센서와 토크 센서, RPM 센서 등 발전 계통에 대한 감시를 위한 센서, 그리고 H-ADCP(Horizontal Acoustic Doppler Current Profiler)와 같은 외력조건에 대한 계측 장비 등이 있다. 센서 설치 후 현재까지 부분적으로 계측된 자료를 소개하고, 향후 건전성 감시시스템 개선 계획을 소개하였다.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.531-532
• /
• 2002

This paper present a gain-clamped L-band EDFA based on reflecting back a portion of backward amplified spontaneous emission into the erbium-doped fiber section, utilizing a fiber Bra99 grating. By using FBG with R=66.1 and 99.9%, the gain is clamped at 15.1 and 14.3㏈, respectively, with a variation of less than 0.2㏈ for an input signal power as high as -5 ㏈m. However, a small noise figure penalty is obtained, which is the consequence of the gain clamping effect.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.201.1-201.1
• /
• 2016

본 연구에서는 펄스형으로 운전하는 플라즈마를 대상으로 하거나 플라즈마 특성의 빠른 변동을 파악하기 위해 1 kHz 이상의 반복율, 5 pulse burst mode와 2 J/pulse 이상의 발진특성을 갖는 Nd:YAG 레이저를 기반으로 하는 광원을 개발하기 위하여 레이저와 전원장치를 설계하였다. 전체 시스템은 MOPA(Master Oscillator Power Amplifier)형태로 구성하고 발진기는 FBG(Fiber Bragg Grating)을 반사경으로 사용한 Yb fiber 레이저를 설계하였다. 또한 설계한 레이저를 작동시킬 전원장치를 연구하였다. 정확한 스위칭과 턴온, 턴오프를 구현하기 위하여 IGBT 스위치를 적용하였고 적절한 저항을 조합하여 전류가 시간에 따라 상승하다가 스위치 턴오프에 급격히 감소하는 형태의 레이저 다이오드 구동에 적합한 삼각파와 비슷한 전류파형을 설계하였다. 추후 설계한 두 장치를 제작하여 테스트를 거친 후, VEST 내부 플라즈마 진단에 적용할 계획이다.