• Journal of the Korean Wood Science and Technology
• /
• v.19 no.2
• /
• pp.40-55
• /
• 1991

To investigate the influence of cross section geometries on the behavior of composite beams in the case of small span to depth ratio and deep beams. the static flexural behavior of composite I-beams and Box- beams was evaluated. 12 types of composite I -beams composed of LVL flanges and particleboard or plywood web and 3 types of composite Box-beams composed of LVL flanges and plywood web were tested under one-point loading. The load-deflection curves were almost linear to failure, therefore, the behavior of tested composite beams was elastic. The theoretical flexural rigidity of composite beams was calculated and compared with observed flexural rigidity. The highest value was found in I-W type beams and the lowest value was found in G-P type beams. The difference between theoretical and observed flexural rigidity was small. Theoretical total deflection of tested composite beams was calculated using flexural rigidity and compared with actual deflection. Shear deflection of these beams was evaluated by the approximation method, solid crosss section method and elementary method. The difference between actual deflection and expected deflection was not found in D, E and F type beams. This defference was small in G, H and I type beams or Box-beam.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.409-412
• /
• 2006

In process of reinforced concrete(RC) box structure, the heat of hydration may cause serious thermal cracking problems. In order to eliminate hydration heat of mass concrete, this paper reports results of hydration heat control in mass concrete using the OCHP(Oscillating Capillary tube Heat Pipe). Recently OCHP is drawn special attention from these points of low cost as well as short construction schedule for the manufacturing of heat exchanger, flexibility, simplification and high performance. There were three RC box molds$(1.2{\times}1.2{\times}1.2m)$ which shows a difference as compared with each other. One was not equipped with OCHP. While others were equipped with OCHP and these were cooled with air natural convection and spraying water respectively. The OCHP was composed of copper pipe with 12 turns(O.D : 4mm, I.D : 2.8mm). The working fluid was R-22 and its charging ratio was 30(Vol. %). In order to analyze the distribution of temperature and index figure of thermal crack in sequential placement of mass concrete, we used HYCON of computer program. As a result of the experiment, the peak temperature decreased about $15.6\sim23.4^{\circ}C$ than the general specimen and the probability of thermal crack generated in mass concrete decreased up to 0%.

• Microbiology and Biotechnology Letters
• /
• v.31 no.1
• /
• pp.83-89
• /
• 2003

2,4-Dichlorophenoxyacetic acid (2,4-D) as a widely used herbicide has caused serious environmental problems because of its difficult decomposition in nature. We isolated the strain capable of metabolizing 2,4-D as sole carbon and energy source by an enrichment culture technique from the 2,4-D contaminated soil collected at orchard in Gwangju, Korea. This strain was identified tentatively as Aeromonas sp. NOH2. With this strain, we established the response surface methodology (Box-Behnken Design) to optimize the principle parameters for maximizing biodegradation of 2,4-D such as culture pH, temperature, and nutrient concentration in liquid batch culture. The ranges of parameters were obtained from preliminary works done at our laboratory and chosen as 5.5, 6.5, and 7.5 for pH, 25, 30, and $35^{\circ}C$ for temperature, and 5, 20, and 35 g/1 nutrient concentration. Initial concentration of 2,4-D was 500 ppm and nutrient source was tryptic soy broth. The experimental data were significantly fitted to a second order polynomial equation using multiple regression. The most important parameter influencing 2,4-D degradation and biomass production was nutrient concentration. For 2,4-D degradation, the optimum values of pH and temperature, and nutrient concentration were obtained at pH (6.5), temperature (31.8 to $32.1^{\circ}C$), and nutrient concentration (29.6 to 30.1.0 g/1).

• English Language & Literature Teaching
• /
• v.17 no.4
• /
• pp.251-271
• /
• 2011

The present study analyzed Korean learners' production of English /z/-/$d{\Box}$/ and /z/-/${\Box}$/ contrasts in terms of native speaker judgments and acoustic measurements. Korean learner's production was judged to be either correct or incorrect by native English speakers. Correct and incorrect productions were then compared with productions of native speakers' in terms of acoustic analyses. The results indicated that Korean speakers' correct production was more similar to that of native speakers by sharing more acoustic cues. Incorrect production by Korean speakers indicated patterns either different or opposite from that of native speakers, confirming native speaker judgments. The results also revealed acoustic cues on which native speakers rely in judging L2 speech, thereby implying that the more consistent along with more number of acoustic cues used by native speakers may facilitate the acquisition of segment contrasts by L2 learners.

• Journal of Korean Society of Water and Wastewater
• /
• v.29 no.2
• /
• pp.183-192
• /
• 2015

Response surface methodology (RSM) based on a Box-Behnken Design (BBD) was applied to optimize the thermal-alkaline pre-treatment operating conditions for anaerobic digestion of flotation scum in food waste leachate. Three independent variables such as thermal temperature, NaOH concentration and reaction time were evaluated. The maximum methane production of 369.2 mL $CH_4/g$ VS was estimated under the optimum conditions at $62.0^{\circ}C$, 10.1% NaOH and 35.4 min reaction time. A confirmation test of the predicted optimum conditions verified the validity of the BBD with RSM. The analysis of variance indicated that methane production was more sensitive to both NaOH concentration and thermal temperature than reaction time. Thermal-alkaline pretreatment enhanced the improvement of 40% in methane production compared to the control experiment due to the effective hydrolysis and/or solubilization of organic matters. The fractions with molecular weight cut-off of scum in food waste leachate were conducted before and after pre-treatment to estimate the behaviors of organic matters. The experiment results found that thermal-alkaline pre-treatment could reduce the organic matters more than 10kD with increase the organic matters less than 1kD.

• Proceedings of the KSAR Conference
• /
• 2001.03a
• /
• pp.19-19
• /
• 2001

Mammalian urothelium undergoes unique membrane specialization by making the asymmetric unit membrane (AUM) that is covered with the apical cell surface during terminal differentiation. The AUM contains several major integral membrane proteins including uroplakin Ia, Ib, II and III. The genes for uroplakins have been cloned from humans and mice, but not from porcine. In this study, we report the cloning of the UPII genomic DNA, which codes for the full length open reading frame for the uroplakin II protein. The deduced amino acid sequence encodes of a hydrophobic NH$_2$-terminal peptide, a prosequence, and a mature protein. The prosequence contains three potential N-glycosylation sites and a RGRR cleavage site that may be involved in uroplakin II processing and maturation. Northern and immunohistochemistry analyses showed that the porcine UPII gene is only expressed in urothelium and that the protein was specifically localized in urothelial superficial cells. A 2kb of upstream in the promoter sequence contains multiple transcription factor binding sites, including GC-box, SPI, AP2, and GATA-box sites, but not for TATA or CAAT-box sequences. Comparison of the porcine UPII promoter sequence with that of the murine by MEME system presented two conserved motifs, suggesting a cis-acting regulatory role for the conserved sequences. Sequence homology between two species in motif A and B was 79% and 80% respectively, although their relative locations were different. During the gestation, mouse bladder at estrus stages and day 10 after parturition showed higher UPII expression, while showed lower expression at peri-implantation stage. Taken together, our results showed that the porcine UPII gene was expressed highly and specifically in the bladder urothelium and that steroid hormones for implantation changed the expression of UPII in the bladder, although the biological significance of UPII remains to be not determined.

• Investigative Magnetic Resonance Imaging
• /
• v.18 no.2
• /
• pp.107-119
• /
• 2014

Purpose : To efficiently evaluate phased array coil performance using a software tool box with which we can make visual comparison of the sensitivity of every coil element between the real experiment and EM simulation. Materials and Methods: We have developed a $C^{{+}{+}}$- and MATLAB-based software tool called Phased Array Coil Evaluator (PACE). PACE has the following functions: Building 3D models of the coil elements, importing the FDTD simulation results, and visualizing the coil sensitivity of each coil element on the ordinary Cartesian coordinate and the relative coil position coordinate. To build a 3D model of the phased array coil, we used an electromagnetic 3D tracker in a stylus form. After making the 3D model, we imported the 3D model into the FDTD electromagnetic field simulation tool. Results: An accurate comparison between the coil sensitivity simulation and real experiment on the tool box platform has been made through fine matching of the simulation and real experiment with aids of the 3D tracker. In the simulation and experiment, we used a 36-channel helmet-style phased array coil. At the 3D MRI data acquisition using the spoiled gradient echo sequence, we used the uniform cylindrical phantom that had the same geometry as the one in the FDTD simulation. In the tool box, we can conveniently choose the coil element of interest and we can compare the coil sensitivities element-by-element of the phased array coil. Conclusion: We expect the tool box can be greatly used for developing phased array coils of new geometry or for periodic maintenance of phased array coils in a more accurate and consistent manner.

• Bulletin of the Korean Mathematical Society
• /
• v.32 no.2
• /
• pp.303-308
• /
• 1995

We consider a torus T, that is, a compact surface with genus 1 and $\Omega = D^2 \times S^1$ topologically with $\partial\Omega = T$, where $D^2$ is the open unit disk and $S^1$ is the unit circle. Let $\omega = (x,y)$ denote the generic point on T. For a smooth immersion $u : T \to R^3$, we define the Dirichlet functional by $$ E(u) = \frac{2}{1} \int_{T} $\mid$\nabla u$\mid$^2 d\omega $$ and the volume functional by $$ V(u) = \frac{3}{1} \int_{T} u \cdot u_x \Lambda u_y d\omege $$.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2001.09a
• /
• pp.239-243
• /
• 2001

대수층에서 오염물질의 이동은 대류, 확산, 흡착 등의 물리화학적 현상에 영향을 받는다. 지하수 유동과 오염 물질 운송에 관련된 분석은 지하수 자원의 관리와 평가, 복원사업에 필요한 요소이다. 본 연구의 목적은 사질대수층에서의 2차원 plume 모니터링을 통하여 오염운의 관측치와 모사치를 비교하므로써 종분산지수와 종/횡분산지수비를 결정하는 것이다. 실내 자유면 대수층 실험에서 MT3D를 이용한 case study로부터 추정된 종분산지수는 0.4 cm였으며 횡/종분산지수비는 1/5로 나타났다.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.11 no.2
• /
• pp.13-19
• /
• 2011

Starting in modern times by Le Corbusier, architectures made by concretes are still developing in these times. For several decades, the shape of box architecture has been the most familiar type of buildings. Of course "The concrete is the type of box building" isn't always right, but what we have most seen was the buildings which has been stylized and made by concretes. Through modern times to these days based on international style and functionalism, the type of box building was the most effective and good profit type of architecture which has not disregarded the capitalism. Free-form building are becoming a common place, and many of these are designed and constructed using sophisticated techniques. The main technique being used is Generative Technology of Form for free-form construction. People's interest is growing in this, and it is becoming widely used both abroad and domestically. The purpose of this paper is to investigate the use of Generative Technology of Form which is a digitally adapted design methodology in architecture. The digital design process used for contemporary buildings share many typical features that exist within a standard digital template, but also an increasing amount of mass customization that has to be produced at an additional cost. This paper will summarize these features in terms of free-form architecture, and in terms of the digital design process. In fact, 3D models have to be conceded as main design products considering features of Free Form Design Architecture. However it is practical to design twice over, because all forms of architectural drawings are 2D. From now on, design of Free Form Design Building is not to separate between design process and practical process, but to compound them as unified design system applied the process to communicate information interactively. For this, it should be required to impose unified digital design process and perform researches about effective way to apply in the field of Free-form Design Architecture.