• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.4
• /
• pp.446-455
• /
• 2017

The improvement of resistance performance for the 4.99 ton class fishing boats was shown. The 4.99 ton fishing boats are the most commonly used one in the Korean coastal region. The evaluation of resistance performance was estimated by the Computational Fluid Dynamics (CFD) analysis. The CFD simulation was performed by the validation for various types of bow shapes on the hull. The optimized hull form from the simulation was selected and showed the best resistance performance. This hull type was tested on the towing tank in the National Institute of Fisheries Science (NIFS). The effective horsepower (EHP) was estimated by the resistance test on the towing tank with the bare hull condition. The drag force on the three service speed conditions was obtained for the resistance analysis to power prediction. The measured drag forces are compared with the results from the CFD simulation with one another. As results of the model tests, it was confirmed that the shape of the bow is an important factor in the resistance performance. The effective horsepower decreased about 30% in comparison with the conventional hull form. Also, the resistance performance improved the reduction of required horsepower, which especially contributed to the energy-saving for the fisheries industry. In the CFD analysis, the resistance performance improved slightly. In this case, the ratio of the residual resistance ($C_R$) in the total resistance ($C_T$) was high. Therefore, the CFD analysis was not enough to satisfy with reflection for the free surface and wave form in the CFD procedure. Both model test and CFD calculation in this study can be applied to the initial design process for the coastal fishing vessel.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.5
• /
• pp.367-375
• /
• 2012

In this study, hull form of main vessel of Korean large purse seiner fishing industry is developed for the improvement of resistance performance as well as for the satisfaction to the Standard of Fishing Convention, ILO. Through the modification of reference hull form parameters and local characteristics, the hull form development is carried out. The optimum hull form parameters are searched by Sequential Quadratic Programing(SQP) method with the power estimation method of Holtrop & Mannen. To minimize the wave resistance, bulbous bow parameters are determined by the bulbous bow design method of Alvarino. The plasmatic curve is redesigned from that of the reference hull by using Lackenby method. The resistance performances of the reference and designed hull forms are estimated by using numerical simulation method. Also, the judgment of seakeeping ability and the estimation of intact stability for the designed hull form is carried out. As a result, the optimum hull form is proposed. To verify the improvement of resistance performance, model tests are carried out in towing tank. The results show that the resistance of the designed hull form is about 14% smaller than that of the reference hull from at design speed. A new hull form proposed in this study can contribute to the development of the main vessel hull form of Korean large purse seiner fishing system.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.442-458
• /
• 2014

Wave induced vibrations increase the fatigue and extreme loading, but this is normally neglected in design. The industry view on this is changing. Wave induced vibrations are often divided into springing and whipping, and their relative contribution to fatigue and extreme loading varies depending on ship design. When it comes to displacement vessels, the contribution from whipping on fatigue and extreme loading is particularly high for certain container vessels. A large modern design container vessel with high bow flare angle and high service speed has been considered. The container vessel was equipped with a hull monitoring system from a recognized supplier of HMON systems. The vessel has been operating between Asia and Europe for a few years and valuable data has been collected. Also model tests have been carried out of this vessel to investigate fatigue and extreme loading, but model tests are often limited to head seas. For the full scale measurements, the correlation between stress data and wind data has been investigated. The wave and vibration damage are shown versus heading and Beaufort strength to indicate general trends. The wind data has also been compared to North Atlantic design environment. Even though it has been shown that the encountered wind data has been much less severe than in North Atlantic, the extreme loading defined by IACS URS11 is significantly exceeded when whipping is included. If whipping may contribute to collapse, then proper seamanship may be useful in order to limit the extreme loading. The vibration damage is also observed to be high from head to beam seas, and even present in stern seas, but fatigue damage in general is low on this East Asia to Europe trade.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.2
• /
• pp.246-252
• /
• 2016

In this study, conceptual design of the fore-body hull form of catamaran type dredging vessel was performed that can effectively remove the contaminated sediments in coastal seabed. The hull form was simpled for the easy hull construction and the resistance performance was investigated to find out the effect of hull form parameters between variation of waterline and angle of entrance, etc. The relation between resistance performance and characteristics of free surface flows according to variation of bow forms was investigated by model testing in the circulating water channel and using Ansys CFX. The improvement of ship resistance performance to the wave resistance decrease due to improved wave pattern has been verified according to move the stem and the volume of the shoulder to the fore part of the vessel.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.9 no.2
• /
• pp.92-97
• /
• 2006

Hull forms of a high speed small boat have been developed through numerical studies. A round bilge type hull form has been drived form a using chine hull form with HCAD, a hull form variation software. Wave resistance and the flow fields around the ships have been computed using well-known software, WAVIS. This software employs Rankine source method with non-linear tree surface condition as well as dry transom boundary conditions. The round bilge hull form showed better resistance performance than to the chine hull form for the whole speed range. However, considering the building and labor costs of the small shipyard, the chine hull form has been selected and its wave resistance characteristics has been improved by modifying the bow regions and applying the stem wedge. It is found that the effect of stem wedge is quite satisfactory to improve the resistance characteristics of high speed chine hull form.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.542-550
• /
• 2007

A geometry modification is one of main keys in achieving a successful optimization. The optimized hull form generated from the geometry modification should be a realistic, faired form from the ship manufacturing point of view. This paper presents a practical hull optimization procedure using a parametric modification function. In the parametric modification function method, the initial ship geometry was easily deformed according to the variations of design parameters. For example, bulbous bow can be modified with several parameters such as bulb area, bulb length, bulb height etc. Design parameters are considered as design variables to modify hull form, which can reduce the number of design variables in optimization process and hence reduce its time cost. To verify the use of the parametric modification function, optimization for KCS was performed at its design speed (FN=0.26) and the wave making resistance is calculated using a well proven potential code with fully nonlinear free surface conditions. The design variables used are key design parameters such as Cp curve, section shape and bulb shape. This study shows that the hull form optimized by the parametric modification function brings 7.6% reduction in wave making resistance. In addition, for verification and comparison purpose, a direct geometry variation method using a bell-shape modification function is used. It is shown that the optimal hull form generated by the bell-shaped modification function is very similar to that produced by the parametric modification function. However, the total running time of the parametric optimization is six times shorter than that of the bell shape modification method, showing the effectiveness and practicalness from a designer point of view in ship yards.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.152-172
• /
• 1992

The ship sailing among waves are suffered the various wave loads that comes from its motion throughout its life. Because there are dynamic, the analysis of ship structure must be considered as the dynamic problem precisely. In the rationally-based design, the dynamic structural analysis is carried out using dynamic wave loads provided from the results of the ship mouton calculation as the rigid body. This method is based on the linear theory assumed low wave height and small amplitude of motion. But at the rough sea condition, high wave height, relatively ship's depth, is induced the large ship motion, so the ship section configulation below water line is rapidly changed at each time. This results in non-linear problem. Considering above situation in this paper, the strength analysis method is introduced for the hull glider among waves considering non-linear hydrodynamic forces. This paper considers that the overall or primary level of the ship structural dynamic loading and dynamic response provided from the non-linear wave forces, and bottom and bow flare impact forces estimated by momentum slamming theory, in which the ship is idealized as a hollow thin-walled box beam using thin-walled beam theory and the finite element method. This method is applied to 40,000 Ton Double-Skin Tanker and attention is paid to the influence of the response of ship speed, wave length and wave height compared with linear strip theory.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.13 no.2
• /
• pp.83-90
• /
• 2010

The hydrodynamic interaction of two floating bodies in waves freely floating or connected by a rigid link is studied by using a boundary element method in the frequency-domain. The exact two-body hydrodynamic coefficients of added mass, wave damping and exciting force are calculated from the radiation-diffraction potential solution of the improved Green integral equation associated with the free surface Green function. The irregular frequencies in the conventional Green integral equation make it difficult to predict the physical resonance of the fluid in the gap between two bodies floating side by side. However, the improved Green integral equation employed in this study is free of irregular frequencies and always yields the exact solution of the multi-body radiation-diffraction potential boundary value problem. The 6 degree-of-freedom motions of two bodies freely floating side by side or connected parallel by a rigid link have been calculated for the incident wave frequencies ranging from 0.1 to 5 radians per second in head, left and right bow quartering seas. The 6-component load of the rigid link have also been presented.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.28-39
• /
• 1991

A study on the optimization problems to find forebode shapes with minimum wavemaking and frictional resistance was performed. The afterbody was fixed as a given hull and only forebode offsets were treated as design variables. Design variables were divided into the offsets of given hull and small variation from them. For the wavemaking resistance calculation, Neumann-Kelvin theory was applied to the given hull and thin ship theory was applied to the small variation. ITTC 1957 model-ship correlation line was used for the calculation of frictional resistance. Hull surface was represented mathmatically using shape function. As object function, such as wavemaking and frictional rersistance, was quadratic form of offsets and constraints linear, quadratic programing problem could be constructed. The complementary pivot method was used to find the soulution of the quadratic programing problem. Calculations were perfomed for the Series 60 $C_{B}$=0.6. at Fn=0.289. A realistic hull form could be obtained by using proper constraints. From the results of calculation for the Series 60 $C_{B}$=0.6, it was concluded that present method gave optimal shape of bulbous bow showing a slight improvement in the wave resistance performance at design speed Fn=0.289 compared with the results from the ship theory only.

• Journal of Ship and Ocean Technology
• /
• v.6 no.4
• /
• pp.19-76
• /
• 2002

The author was appointed by the UK Department of Transport as a fellow Assessor with R. A. Williams during Lord Donaldson's Assessment (1995) of the loss of the OBO ship DERBYSHIRE and in 1996 as a UK Assessor for the planning and surveys of the wreck. He relinquished his appointment in October 1997 and was not thereafter Involved in the review and analysis of data gathered. This paper may be considered to be complementary to the reports of the UK and EC Assessors (Williams and Torchio, 1998a and 1998b) which followed that review and analysis. The paper deals with the history and loss of the ship, Including the concept developed in 1995 of 13 possible loss scenarios in a formal safety Risk Matrix of probability and seriousness. It analyses abnormal wave effects on hatch cover collapse, on ship bending, and on flooding of bow spaces and no. 1 hold. The implosion-explosion mechanics during sinking is outlined to explain the devastation of the wreck. The 1996 and 1997 underwater surveys are outlined as are the findings of fact. Each of the final 14 loss scenarios is analysed in the light of the firm and circumstantial survey evidence, plus many other factors of survey experience, analyses and experiments. The updated Risk Matrix speaks for itself and leads to the prime conclusions and major recommendations.