• Tribology and Lubricants
• /
• v.14 no.4
• /
• pp.37-43
• /
• 1998

The friction loss between piston rings and cylinder liner is due to the tension of the piston rings. Lubricant is usually supplied to reduce the friction. However, the sliding speed of the piston varies during the reciprocating cycle and is very low near TDC(Top Dead Center)/BDC(Bottom Dead Center), where the hydrodynamic lubrication cannot be sustained. Since the lubrication regime is shifted from the hydrodynamic to the boundary lubrication near TDC/BDC, wear particles are easily generated so that the friction loss becomes bigger and bigger due to the plowing effect of wear particles. In this study, for the purpose of reducing the friction loss, an undulated surface is adopted to the cylinder liner to trap wear particles. The friction force variations, which are measured by strain gaged, show that the concept of undulated surface is one of the promising methods to effectively reduce the friction between piston rings and cylinder liner.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.859-865
• /
• 2001

This paper reports on the theoretical analysis of mixed lubrication for the piston ring. The analytical model is presented by using the average flow and asperity contact model. The cyclic variations of the nominal minimum oil film thickness are obtained by numerical iterative method. The total friction is calculated by using the hydrodynamic and asperity contact theory. The effect of the roughness height, pattern, and engine speed on the nominal minimum film thickness, friction force, ad frictional power losses are investigated. As the roughness height increases, the nominal oil film thickness and total friction force increase. Also, the effect of the surface roughness on the boundary friction is dominant at low engine speed and high asperity height. The longitudinal roughness pattern shows lower mean oil film pressure and thinner oil film thickness compared to the case of the isotropic and transverse roughness patterns.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.11a
• /
• pp.61-67
• /
• 2000

Many research works for improving a boundary lubrication performance have been executed by using solid lubricants, and been tried to apply an engine lubrication. However those general lubricants like MoS$_2$ or PTFE have not been applied on engines due to the extreme conditions such as very high temperature and pressure by combustion process in a cylinder. A copper nickel alloy fine particle has been introduced and studied. In this Paper the lubricant using the alloy Particles is applied on a marine diesel engine and assessed by the engine performance test The results showed the increase of cylinder pressure related strongly to the engine efficiency as well as the improving the engine lubrication performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.56-64
• /
• 2000

A friction force measurement system using the floating liner method was developed to study the frictional behavior of piston rings. The measurement system was carefully designed to control the effect of the piston secondary motion and the temperature of cylinder wall and oil. The friction force between the barrel shaped piston ring and the cylinder liner, was measured under the condition of flooded oil supply. The measured friction forces were classified into five frictional modes with regard to the combination of predominant lubrication regimes(boundary, mixed and hydrodynamic lubrication) and stroke regions(midstroke and dead centers). The modes could be identified on the Stribeck diagram of the friction coefficients and the dimensionless number of ㎼/p, where the friction coefficients are evaluated at near the midstroke and dead centers.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.96-99
• /
• 2001

The fatigue life of support bearings is one of the most critical factors for the performance of a control rod driving mechanism. They are operated at high temperature and high pressure and especially lubricated with dramatically low viscosity water. The support bearing is made of standardized 440C stainless steel, and it supports thrust load including the weight of the driving system and external force. Friction and wear characteristics of this material operating under severe lubrication condition is not well known yet, although it is expected to be changed with respect to temperature and boundary pressure. So the friction characteristics are investigated in sliding conditions using the reciprocating tribometer which can simulate the operating conditions. Highly purified water is used as lubricant, and the water is heated up and pressurized. Friction farce on the reciprocating specimens is monitored by the load cells. The results of the experiments are presented in this paper.

• Tribology and Lubricants
• /
• v.32 no.1
• /
• pp.24-31
• /
• 2016

In this paper hydrodynamic lubrication analysis is carried out to investigate the effects of groove location on the lubrication performance of a piston and cylinder system in a linear compressor. The rectangle shaped grooves having a constant groove depth and width are applied on the lubrication area of the piston. The Universal Reynolds equation is used to calculate the oil film pressure, and the Elrod algorithm with the finite different method is used to solve the governing equation. The JFO boundary condition is applied to predict cavitation regions. Transient analysis for different locations of the grooves on the piston is carried out using the typical operating condition of the linear compressor in order to estimate the variations of frictional power losses and minimum film thicknesses. When the grooves are applied on the lubrication area, both the frictional power loss and the minimum film thickness decrease. The frictional power loss can be reduced effectively, while maintaining a minimum film thickness to enable the piston operation without direct contact with the cylinder surface, by means of choosing a proper location of the grooves. The optimum location of the grooves to improve a lubrication performance depends on the operation condition or the system requirements specification.

• Tribology and Lubricants
• /
• v.25 no.1
• /
• pp.56-60
• /
• 2009

A journal bearing is used in a hydrodynamic lubrication state, but it becomes a boundary lubrication state that asperity of a contact part touch each other when pressure is too high and an enough oil film is not formed by viscosity change due to lubricating oil temperature. At this time, abrasion due to contact between a journal and a bearing is unavoidable, and scuffing damage that the journal adheres to the bearing occurs if the process is repeated. Damage of the journal bearing is an important problem because it gives huge damage to a machine and can generate large accidents such as economic loss and human life damage. In this study, method for using the pull-up resistor concept was introduced as the monitoring technology. This monitoring system is important to enhance reliability of the engine.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.269-270
• /
• 2002

Antiwear(AW) properties of phoshphonic acid derivatives for trimethylolpropane (TMP) esters were investigated under boundary conditions. AW effect of dialkyl phosphonates depends on polarity of base fluid. They provide good AW performance in less polar TMP esters, whereas their AW effect is not sufficient in polar TMP esters. Amine salts of phosphonic acid were developed as new AW additiνe system for TMP esters. They provide excellent AW performance even in polar TMP esters.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.53-58
• /
• 2001

Fractal dimension is the method to measure the roughness and the irregularity of something that cannot be defined obviously by Euclidean dimension. And the analysis method of this dimension don't need perfect, accurate boundary and color like analysis lot diameter, perimeter, aspect or reflectivity of wear particles or surface. If we arranged the morphological characteristic of various wear particle by using the characteristic of fractal dimension, it might be very efficient to the diagnosis of driving condition. In order to describe morphology of various wear particle, the wear test was carried out under friction experimental conditions. And fractal descriptors was applied to boundary and surface of wear particle with image processing system. These descriptors to analyze shape and surface wear particle are boundary fractal dimension and surface fractal dimension.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.215-220
• /
• 2004

Molecular Dynamics(MD) method was used to investigate the change of friction force due to interaction between dislocations and a grain boundary when a Ni tip was scratched on a Cu bicrystal. The substrate comprised a Cu bicrystal containing a vertical$\Sigma=5(210)$ grain boundary. The moving tip for scratching simulation was consisted of fixed Ni atoms emulating a rigid tip. The indentation depth was $3.6\AA$ and the scratching was performed along <110>direction in the first grain. As the scratching was continued, nucleation and propagation of dislocations were observed. In the early stage, the grain boundary played as a barrier to moving dislocations and interrupting further dislocation movement with no dislocation resulting in no propagation across the grain boundary. As the Ni tip approached the grain boundary, dislocations were nucleated at the grain boundary and propagated to the second grain. However, stick-slip phenomena that were observed on a single crystal scratching were not observed in the bicrystal. And, instead, irregular oscillation of friction force was observed during the scratching due to the presence of a grain boundary.