• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.37-43
• /
• 1998

The friction loss between piston rings and cylinder liner is due to the tension of the piston rings. Lubricant is usually supplied to reduce the friction. However, the sliding speed of the piston varies during the reciprocating cycle and is very low near TDC(Top Dead Center)/BDC(Bottom Dead Center), where the hydrodynamic lubrication cannot be sustained. Since the lubrication regime is shifted from the hydrodynamic to the boundary lubrication near TDC/BDC, wear particles are easily generated so that the friction loss becomes bigger and bigger due to the plowing effect of wear particles. In this study, for the purpose of reducing the friction loss, an undulated surface is adopted to the cylinder liner to trap wear particles. The friction force variations, which are measured by strain gaged, show that the concept of undulated surface is one of the promising methods to effectively reduce the friction between piston rings and cylinder liner.

• International Journal of Automotive Technology
• /
• 제7권3호
• /
• pp.289-294
• /
• 2006

Better fundamental understanding of the interactions between the in-cylinder flows and combustion process is an important requirement for further improvement in the fuel economy and emissions of internal combustion(IC) engines. Flow near a spark plug at the time of ignition plays an important role for early flame kernel development(EFKD). Velocity data measurements in this study were made with a two-component laser Doppler velocimetry(LDV) near a spark plug in a single cylinder optical spark ignition(SI) engine with a heart-shaped combustion chamber. LDV velocity data were collected on an individual cycle basis under wide-open motored conditions with an engine speed of 1,000rpm. This study examines and compares the flow fields as interpreted through ensemble, cyclic and discrete wavelet transformation(DWT) analysis. The energy distributions in the non-stationary engine flows are also investigated over crank angle phase and frequency through continuous wavelet transformation(CWT) for a position near a spark plug. Wavelet analysis is appropriate for analyzing the flow fields in engines because it gives information about the transient events in a time and frequency plane. The results of CWT analysis are provided and compared with the mean flows of DWT first decomposition level for all cycles at a position. Low frequency high energy found with CWT corresponds well with the peak locations of the mean velocity. The high frequency flows caused by the intake jet gradually decay as the piston approaches the bottom dead center(BDC).

• 해양환경안전학회지
• /
• 제25권7호
• /
• pp.953-960
• /
• 2019

밀러 사이클은 흡입밸브 닫힘 시기 조정을 통해 압축비를 줄임으로써 NOx의 저감과 연료소비율 개선이 동시에 가능하다는 점(밀러 효과)에서 디젤엔진에 매우 활발하게 채택되어지고 있다. 밀러 사이클은 흡입 밸브를 BDC 이전에 닫는 Early 밀러 방식과 BDC 이후에 닫는 Late 밀러 방식으로 나눌 수 있다. 저속에서는 체적효율의 증가를 꾀할 수 있는 Late Miller가 유리한 반면, 중속, 고속에서는 IVC 이후 BDC 까지의 피스톤 하강 과정의 흡기의 팽창에 따른 내부 온도 감소 효과 높은 Early 밀러가 유리하다. 따라서 Early 밀러와 Late 밀러의 효과를 고려하여 운전 조건에 적합한 밀러 구현 방법을 채택할 필요가 있다. 본 연구에서는 4행정 엔진을 대상으로 2단 과급 시스템의 적용하고 흡·배기 밸브 오버랩(valve overlap)의 감소를 통해 밀러 효과를 강화하는 과정과 밸브 조정 기구를 통한 밸브 조건의 변화가 밀러 효과에 미치는 영향을 고찰하였다. 결과적으로 2단과급과 밀러사이클, 밸브 오버랩 감소와 흡입밸브 리프트 증가를 통해 연료소 비율과 최고연소온도 감소의 효과를 확인하였다.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.206-215
• /
• 2013

In this paper, a synchronization control technique of dual-servo motor driven press system is proposed. An independent cascade PID control technique has been applied to the conventional press system for advancement of control stability. However, it is not easy to reduce synchronous error using the independent cascade PID control technique when some different load disturbances are involved in each motor. The eccentric error of the slide caused by the problem degrade the control performance of the BDC(Bottom Dead Center). In order to achieve reduction of the synchronous error between two servo motors and accurate position control simultaneously, a new control scheme comprised with cascade PID control loop and cross-coupling loop is proposed. In simulation using Matlab SIMULINK, the AC servo system is designed. The control performance of proposed technique is compared with conventional control technique to the model of AC servo system. Also, the sub-scale model of dual-servo motor driven press system which can replicate the slide motion is constructed for experimental verification for the performance of the proposed control technique. The cross-coupling control technique reveals more precise and stable performances in the position and synchronization controls.