• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.1
• /
• pp.65-75
• /
• 1990

There have been many methods for measuring the injection rate of diesel engines, but the results of them are not always identical and the reason for the discordance is not clear. Besides, a single shot injection equipment has been used for the fuel spray and the combustion research of diesel engines, but the results of experiment using the equipment don't apply to a volleyed shot injection of real engines. This paper investigates the merits and faults of the Bosch's method and the Zeuch's method, at the same, this paper also compares the injection rates of single shot inject rates of single shot injection and a volleyed shot injected by the Bosch's method. the results are summarized as follows: (1) The measurement error of the Bosch's method is about $\pm$1%, therefore, its accuracy is reliable. (2) By the Bosch's method, as the speed and the load of fuel pump increase, the injection rate becomes higher, on the contrary, the injection period(ms) shortens as the speed increases and the load decreases. (3) In this experiment, the injection rate of a single shot injection is lower than that of a volleyed shot injection under the same conditions. (4) The bulk modulus of elasticity using the Zeuch's method increases in proportion to the back pressure. (5) The Zeuch's method is less accurate than the Bosch's method.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.3-6
• /
• 2004

This study aims to estimate, in monetary figures, the environmental value of recreational theme park- Huis Ten Bosch (HTB), located in Nagasaki Prefecture, Japan, through the integration of both contingent valuation method (CVM) and remote sensing. In the analysis, we have estimated the environmental value of HTB through CVM. Then, we have compared this amount with the valuation made by using remote sensing. The results of the study would provide the interest groups some monetary base, to value the worth of environmental restoration activities undertaken by HTB.

• Wind and Structures
• /
• v.5 no.2_3_4
• /
• pp.257-266
• /
• 2002

In the recent years flow around bridges are investigated using computer modeling. Selvam (1998), Selvam and Bosch (1999), Frandsen and McRobie (1999) used finite element procedures. Larsen and Walther (1997) used discrete vorticity procedure. The aeroelastic instability is a major criterion to be checked for long span bridges. If the wind speed experienced by a bridge is greater than the critical wind speed for flutter, then the bridge fails due to aeroelastic instability. Larsen and Walther (1997) computed the critical velocity for flutter using discrete vortex method similar to wind tunnel procedures. In this work, the critical velocity for flutter will be calculated directly (free oscillation procedure) similar to the approaches reported by Selvam et al. (1998). It is expected that the computational time required to compute the critical velocity using this approach may be much shorter than the traditional approach. The computed critical flutter velocity of 69 m/s is in reasonable comparison with wind tunnel measurement. The no flutter and flutter conditions are illustrated using the bridge response in time.

• Archives of design research
• /
• v.17 no.1
• /
• pp.383-392
• /
• 2004

The power tools is the product using working power generated by electric motor. Many companies are manufacturing numerous devices. Main features of tools are included various assembled products, small, light and solid and durable enough to match several standards. Fundamental requirements for the product is excellent performance and convenience for use. The quality of them depends on the equipped motor'(s) capability, accuracy of gear and endurance against worn-out. By adapting the state-of-the-art parts, they could be used in the place from home to heavy industry broadly. They can be classified electronic drills, grinders, saws and sanders families for the household appliances. For industrial tools, bore drill, grinder, polisher, and driver drill are classified as special and high priced group. This study presents the strategy of power tool development of BOSCH, BLACK&DECKER and KEYANG. Their products were analyzed in terms of product line and product mix concept. Then they are examined by design elements, such as color, shape and material for housing. As an analysis method, the image scale parameter and criteria were applied to each company's product.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2542-2544
• /
• 2000

In this paper, CAN(Controller Area Network)is used to solve the wire harness problem in the outside mirror of automobile which has a lot of functions in narrow space. If the number of wires is reduced, it has benefits of lower product cost and maintenance. CAN was originally developed by the German company Robert Bosch for use in the car industry to provide a cost-effective communications bus for in car electronics and as alternative to expensive and cumbersome wiring looms. CAN controller is a serial communication protocol which efficiently supports distributed real-time control with a very high level of security. The communication between master CAN controller and slave CAN controller is realized and controller's performance is tested by experiment.

• Hwankyungkyoyuk
• /
• v.25 no.2
• /
• pp.210-223
• /
• 2012

This study is aimed to identify environmental management expert's competencies, to analyze educational need, and to improve curriculum of Global Environmental Management major of 'Seoul National University'. Environmental experts are divided into three groups through 'the right people' of the Global Environmental Management major: environmental management businessman, environmental management policy maker, environmental management international cooperator. This study selected three high-performers of each categories through recommendation and made them build a competency model for what the high-performer's behavioral characteristics is. And the educational needs analysis was carried out by practitioners in environmental management field. This study ordered the priority of educational needed competencies by method of Borich's proposal. The high priority of competencies that should be educated preferentially are as follows: responding to environmental policy, analyzing domestic & foreign environmental policy and design international environmental cooperation project. To be secure the consistency with the field need and university curriculum, it is needed to find various interventions in environmental management education and to improve curricula focused on specific competencies.

• Journal of Mechanical Science and Technology
• /
• v.19 no.5
• /
• pp.1194-1205
• /
• 2005

The common-rail injection systems, as a new diesel injection system for passenger car, have more degrees of freedom in controlling both the injection timing and injection rate with the high pressure. In this study, a piezo-driven injector was applied to a high pressure common-rail type fuel injection system for the control capability of the high pressure injector's needle and firstly examined the piezo-electric characteristics of a piezo-driven injector. Also in order to analyze the effect of injector's needle response driven by different driving method on the injection, we investigated the diesel spray characteristics in a constant volume chamber pressurized by nitrogen gas for two injectors, a solenoid-driven injector and a piezo-driven injector, both equipped with the same injection nozzle with sac type and 5-injection hole. The experimental method for spray visualization was based on back-light photography technique by utilizing a high speed framing camera. The macroscopic spray propagation was geometrically measured and characterized in term of the spray tip penetration, spray cone angle and spray tip speed. For the evaluation of the needle response of the above two injectors, we indirectly estimated the needle's behavior with an accelerometer and injection rate measurement employing Bosch's method was conducted. The experimental results show that the spray tip penetrations of piezo­driven injector were longer, on the whole, than that of the solenoid-driven injector. Besides we found that the piezo-driven injector have a higher injection flow rate by a fast needle response and it was possible to control the injection rate slope in piezo-driven injector by altering the induced current.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.16-22
• /
• 2004

Dimethyl Ether (DME) has been considered as one of the most attractive alternative fuels for a compression ignition engine. The major advantage of DME-fuelled engine is a great potential for soot-free combustion without sacrificing an inherent high thermal efficiency of diesel engine, despite a necessity for modification of the conventional fuel injection system. An experimental study on DME and conventional diesel sprays was conducted by employing a common-rail type fuel injection system with a 5-holes sac type nozzle, including a constant volume vessel pressurized with nitrogen gas. The injection rates of DME and diesel fuel were recorded with the Bosch type injection rate meter. The injection delay of DME was shorter than that of diesel fuel. The measured injection rates of DME and diesel fuel were correlated with spray penetrations. The prediction method of spray penetration was established using the injection rates, which was verified with the Dent's penetration model and found to agree well for DME case.

• Journal of ILASS-Korea
• /
• v.22 no.4
• /
• pp.210-217
• /
• 2017

A gasoline direct injection engine has an intake air temperature can be lowered by the fuel vaporization in the combustion chamber increase the volume efficiency is high compression ratio. Therefore, study for injection rate and characteristics which influence mixture formation in combustion chamber is important. Movement of the injector needle has a direct effect on the injection of the fuel, such as formation of cavitation, the fuel injection rate, etc. Therefore, recent studies on the dynamic characteristics of the injector considering the movement of the needle have been reported, but it takes a lot of time and cost to experimentally confirm the movement of the needle inside the injector. In this study, AMESim, a commercial 1-D code, and Star-CCM+, a 3-D CFD code, were used to predict the dynamic performance of the injector with needle motion. In order to predict the movement of the needle under the high pressure, the result of the surface pressure distribution according to the movement of the needle was derived by using the morphing technique of flow analysis. In addition, we predicted the injection rate of the injector considering the movement of the needle in conjunction with the 1-D code. The injection rate of the injector was measured by the BOSCH's method and the results were similar to those of the simulation results. This method can predict the injection rate and injection characteristics and this result is expected to be used to predict the performance of gasoline direct injection engines with low cost and time in the future.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.89-95
• /
• 2013

In this work, the evaluation of swirl nozzle injector performance was conducted by investigating effective area ($A_{eff}$), injection mass ($m_{inj}$), injection rate ($Q_{inj}$), and injection delay ($t_{delay}$) under various test conditions. To achieve these, fuel injection analysis system which was composed of fuel supply system, injection system, and control system was installed. At the same time, the swirl nozzle that had 12 orifice hole with $120^{\circ}$ injection angle was used in this work. It was revealed that the difference of injection mass ($m_{inj}$) between base and swirl nozzle injector increased as the injection pressure ($P_{inj}$) and energizing duration ($t_{eng}$) decreased under the same test conditions. The maximum injection rate ($Q_{inj}$) of swirl nozzle injector was higher than base nozzle injector about 2~5%. The injection performance of swirl nozzle was better than base nozzle at low injection pressure ($P_{inj}$) and short energizing duration ($t_{eng}$) conditions.