• Bulletin of the Korean Chemical Society
• /
• v.11 no.4
• /
• pp.307-309
• /
• 1990

The stereoselectivity of the reaction between methyl vinyl ketone dimer, which contains two possible sites of chelation, and zinc borohydride or diisobutylaluminum hydride has been studied in order to illuminate the factors involved in the high levels of asymmetric induction obtained in the bicyclic system. The conditions for the formation of the exo-5,7-dimethyl-6,8-dioxabicyclo[3.2.1]octane are DIBAH reduction of MVK dimer in ether at reflux followed by acidic cyclizatioan, and for the endo isomer are $Zn(BH_4)_2$ reduction with $ZnCl_2$ at $0^{\circ}C.$.

• Journal of the Korean Chemical Society
• /
• v.47 no.4
• /
• pp.315-324
• /
• 2003

In this study, a new method is presented to produce stable hydrophobic metal alloy nanocluster in chloroform solution including surfactant NaAOT(sodium bis(2-ethylhexyl)-sulfosuccinate) via the chemical reduction of metal salt $(HAuCl_4,\AgNO_3,\Cu(NO_3)_2)$ by sodium borohydride. For the alloy nanocluster, several samples were prepared by changing the molar ratio of Au/Cu, Au/Ag alloy nanocluster, 3:1, 1:1, 1:3. The alloy nanoclusters were characterized by UV-Visible spectrophotometer, TEM(Transmission Electron Microscope), and XPS(X-ray Photoelectron Spectrometer). With the change of the mole ratio of the alloy component, the wavelengths of the surface plasmon absorption shift linearly from 520 nm of the pure Au nanocluster to 570 nm of the pure Cu nanocluster for Au/Cu alloy nanoclusters and from 405 nm to 520 nm for Au/Ag alloy nanoclusters. The chemical shifts of the Au4f, Ag3d, Cu2p XPS peaks were observed with changing the molar ratio of the alloy element. The alloy nanoclusters in chloroform solution were made uniformly in size and colloidally stable for long periods of time. These results indicate that the method here is a very effective method for synthesizing hydrophobic alloy nanoclusters with uniform or nearly uniform particle size distribution.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.19 no.2
• /
• pp.127-135
• /
• 1986

Each molecular weight (Mw) fraction of melanoidins prepared from a D-glucose and glycine system, i. e., Mw below 1,000, Mw between 1,000 to 5,000 and Mw above 5,000 and nondialyzable and ozone-treated melanoidins were reacted with heat-induced mutagens such as Trp-P-1, Trp-P-2, Glu-P-1, Glu-P-2 and IQ at $37^{\circ}C$ for 30 min. The inhibitory effects of the melanoidins on the mutagens increased with increasing molecular weight. The reducing ability ana antioxidative activity of melanoidins also increased in proportion to the increase in molecular weight, whereas the mutagenic inhibitory effect decreased on reduction of the melanoidins with sodium borohydride. It was also observed that a part of Trp-P-1 was adsorbed to melanoidin molecules. On modification of amino groups of these mutagens with carbonyl compounds derived through the Maillard reaction such as diacetyl and glyceraldehyde, their mutagenic activities were remarkably suppressed. Accordingly, it is speculated that the mutagenic inhibitory action of melanoidins is due to their reducing ability and antioxidative activity, and electrostatic binding and carbonyl groups of the melanoidin molecules.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.1
• /
• pp.1-5
• /
• 2005

Nitrate reduction with zero valent iron $(Fe^0)$ has been extensively studied, but the proper treatment for ammonium byproduct has not been reported yet. In groundwater, however, ammonium is regarded as contaminant species, and particularly, its acceptable level is regulated to 0.5 mg-N/L. for drinking water. This study is focused on developing new material to reduce nitrate and properly remove ammonium by-products. A new material, Fe-loaded zeolite, is derived from zeolite modified by Fe(II) chloride followed by reduction with sodium borohydride. Batch experiments were performed without buffer at two different pH to evaluate the removal efficiency of Fe-loaded zeolite. After 80 hr reaction time, Fe loaded zeolite showed about $60\%$ nitrate removal at initial pH of 3.3 and $40\%$ at pH of 6 with no ammonium release. Although iron filing showed higher removal efficiency than Fe-loaded zeolite at each pH, it released a considerable amount of ammonium stoichiometrically equivalent to that of reduced nitrate. In terms of nitrogen species including $NO_3-N$ and $NH_4^+-N$, Fe-loaded zeolite removed about $60\%\;and\;40\%$ of nitrogen in residual solution at initial pH of 3.3 and 6, respectively, while the removal efficiency of iron filing was negligible.

• Korean Chemical Engineering Research
• /
• v.53 no.1
• /
• pp.11-15
• /
• 2015

Sodium borohydride, $NaBH_4$, shows a number of advantages as hydrogen source for portable proton exchange membrane fuel cells(PEMFCs). Properties of $NaBH_4$ hydrolysis reaction using unsupported Co-B, Co-P-B catalyst were studied. BET surface area of catalyst, yield of hydrogen, effect of $NaBH_4$ concentration and durability of catalyst were measured. The BET surface area of unsupported Co-B catalyst was $75.7m^2/g$ and this value was 18 times higher than that of FeCrAlloy supported Co-B catalyst. The hydrogen yield of $NaBH_4$ hydrolysis reaction by unsupported catalysts using 20~25 wt% $NaBH_4$ solution was 97.6~98.5% in batch reactor. The hydrogen yield decrease to 95.3~97.0% as the concentration of $NaBH_4$ solution increase to 30 wt%. The loss of unsupported catalyst was less than that of FeCrAlloy supported catalyst during $NaBH_4$ hydrolysis reaction and the loss increased with increasing of $NaBH_4$ concentration. In continuous reactor, hydrogen yield of $NaBH_4$ hydrolysis was 90% using 1.2 g of unsupported Co-P-B catalyst with $3{\ell}/min$ hydrogen generation rate.

• Korean Chemical Engineering Research
• /
• v.55 no.1
• /
• pp.13-18
• /
• 2017

Sodium borohydride, $NaBH_4$, shows a number of advantages as hydrogen source for UAV PEMFC (Unmaned Aerial Vehicle Proton Exchange Membrane Fuel Cells). In order to use for UAV, the weight and volume of byproduct should be small after $NaBH_4$ hydrolysis reaction. Therefore, the weight and volume of byproduct were studied after $NaBH_4$ hydrolysis reaction using unsupported catalyst. The effect of catalyst type, concentration of $NaBH_4$, concentration of NaOH and thickness of catalyst pack on the weight and volume of byproduct were studied. Most of byproduct was $NaB(OH)_4$ and superficial volume of byproduct increased due to foam evolved from byproduct. The weight and volume of byproduct were not affected by concentration of NaOH used stabilizer. The weight of byproduct decreased as concentration of $NaBH_4$ solution increased, but maximum volume of byproduct obtained at 23 wt% of $NaBH_4$. Suitable defoaming agent reduced the volume of byproduct.

• Korean Chemical Engineering Research
• /
• v.56 no.5
• /
• pp.641-646
• /
• 2018

Sodium borohydride, $NaBH_4$, shows a number of advantages as hydrogen source for portable proton exchange membrane fuel cells (PEMFCs). Properties of $NaBH_4$ hydrolysis reaction using activated carbon supported Co-B/C, Co-P-B/C catalyst were studied. BET surface area of catalyst, yield of hydrogen, effect of $NaBH_4$ concentration and durability of catalyst were measured. The BET surface area of carbon supported catalyst was over $500m^2/g$ and this value was 2~3 times higher than that of unsupported catalyst. Hydrogen generation of activated carbon supported catalyst was more stable than that of unsupported catalyst. The activation energy of Co-P-B/C catalyst was 59.4 kJ/mol in 20 wt% $NaBH_4$ and 14% lower than that of Co-P-B/FeCrAlloy catalyst. Catalyst loss on activated carbon supported catalyst was reduced to about 1/3~1/2 compared with unsupported catalyst, therefore durability was improved by supporting catalyst on activated carbon.

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.758-762
• /
• 2019

Sodium borohydride,$NaBH_4$, has many advantages as hydrogen source for portable proton exchange membrane fuel cells (PEMFC). When PEMFC is used for marine use, $NaBH_4$ hydrolysis using seawater is economical. Therefore, in this study, hydrogen was generated by using seawater instead of distilled water in the process of hydrolysis of $NaBH_4$. Properties of $NaBH_4$ hydrolysis reaction using activated carbon supported Co-B/C catalyst were studied. The yield of hydrogen decreased as $NaBH_4$ concentration and NaOH concentration were increased during $NaBH_4$ hydrolysis using sea water. At higher concentrations of $NaBH_4$ and NaOH, byproducts adhered to the surface of the catalyst after hydrolysis reaction using sea water, reduced hydrogen yield compared to distilled water. The activation energy of $NaBH_4$ hydrolysis is 59.3, 74.4 kJ/mol for distilled water and sea water, respectively. In order to increase the hydrogen generation rate in seawater as high as distilled water, the reaction temperature has to be increased by $80^{\circ}C$ or more.

• Korean Chemical Engineering Research
• /
• v.59 no.4
• /
• pp.503-507
• /
• 2021

Sodium borohydride, NaBH₄, has many advantages as hydrogen source for portable proton exchange membrane fuel cells (PEMFC). When PEMFC is used outdoors as a transport type, it is economical to hydrolyze NaBH₄ using fresh water instead of distilled water. Therefore, in this study, hydrogen was generated using fresh water instead of distilled water during the NaBH₄ hydrolysis process. The properties of NaBH₄ hydrolysis were studied using an activated carbon-supported Co-P-B/C catalyst. Fresh water did not generate tetrahydrate during the NaBH₄ hydrolysis process, and distilled water produced tetrahydrate by-products, which consumed a lot of water during the hydrolysis process, indicating that at the end of the reaction at a high concentration of 25% or more of NaBH₄, dry by-products and unreacted NaBH₄ remained. As a result, when fresh water was used, the hydrogen yield and hydrogen generation rate were higher than that of distilled water at a high concentration of 25% or more of NaBH₄, indicating that it is suitable for use in transport-type fuel cells such as unmanned aerial vehicles.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.5
• /
• pp.1325-1334
• /
• 2021

This study reports the development of a manufacturing method of synthesizing colloidal gold using catalysts available for cosmetics and an anti-aging ampoule with skin improvement effects using it. Nano-colloidal gold was synthesized by using ascorbic acid and sodium borohydride as a reducing catalyst in hydrogen tetrachloroaurate tetrahydrate. It was confirmed that the particles became smaller as the mass of the content of ascorbic acid, which is a catalyst, increased. On the other hand, as the mass of sodium borohydride increased, the particle size tended to increase. In order to control the colloidal gold reaction rate, particles having 100 to 500 nm of a particle diameter distribution could be obtained using xanthan gum and hydroxyethylcellulose. The optimal synthesis conditions could be obtained by reacting for 1 to 4 hours at 18℃, a reduced pressure state of 20 to 75 mmHg, a stirring speed of 10~50 rpm. The synthesized colloidal gold had a unique smell of dark pink, pH = 5.5, specific gravity of 1.0032, and viscosity of 80 to 310 cps. As an application of skin care cosmetics, anti-aging ampoule has been developed, and it is expected to be used for various prescriptions and formulations using it.