• Composites Research
• /
• 제17권6호
• /
• pp.14-21
• /
• 2004

본 연구에서는 몇 가지 접합 방법에 따라 일방향 복합재료 단일 겹치기 접합 조인트의 파손 과정, 모드 및 강도를 실험적으로 평가하였다 접합 방법으로는 접착제 없는 동시성형, 접착제를 사용한 동시성형 및 이차 접합의 세 가지를 고려하였다 또한 이차 접합 조인트에서 몇 가지 파라미터의 영향도 살펴보았다. 접착제 없는 동시성형 시편은 가장 우수한 조인트 강도를 나타내었다. 이차접합 조인트에서는 접착제 층의 점진적인 파손이 발생하였다. 접착제의 재료 및 접합 강도가 상대적으로 강한 필름 접착제의 동시성형 조인트는 갑작스런 층간분리 파손이 발생하였으며 이차 접합 조인트보다 더 낮은 파손 강도를 나타내었다. 이차 집합 조인트에서 층간분리 파손이 발생하지 않은 것은 접착제 층에서의 균열 진전 및 점진적 파손이 층간분리 파손을 방지한 것으로 보인다. 따라서 복합재료 접합 조인트의 파손 강도는 접착제의 재료 강도 또는 접착 성능과 항상 비례하지 않으며 이것은 복합재료가 층간 분리 파손에 약하기 때문이다.

• 대한금속재료학회지
• /
• 제48권12호
• /
• pp.1116-1122
• /
• 2010

Metal interconnections of multilayer Al/Ni and TiW/seed-Ni/Ni were formed on glass, and the adhesion strength and nanoindentation response of the composite layers were evaluated. The Al/Ni multilayer was formed by an anodic bonding of glass to Al and subsequent electroless plating of Ni, while the TiW/Ni multilayer was fabricated by sputter deposition of TiW and seed-Ni onto glass and electroless plating of Ni. Because of the diffusion of aluminum into glass during the anodic bonding, anodically bonded glass/Al joint exhibited greater interfacial strength than the sputtered glass/TiW one. The Al/Ni on glass also showed excellent resistance against delamination by bending deformation compared to the TiW/seed-Ni/Ni on glass. From the nanoindentation experiment of each metal layer on glass, it was found that the aluminum layer had extremely low hardness and elastic modulus similar to the glass substrate and played a beneficial role in the delamination resistance by lessening stress intensification at the joint. The indentation data of the multilayers also supported superior joint reliability of the Al/Ni to glass compared to that of the TiW/seed-Ni/Ni to glass.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.468-476
• /
• 1998

The purpose of this study was to observe the morphologic change of dentinal surface, adhesion in interface between dentin and bonding agents, and penetration pattern of resin tags into dentinal tubles according to bonding procedure of ONE-STEP universal adhesive system. Ten extracted human molars were mounted in dental stone and sectioned to expose mid-coronal occlusal dentin and again sectioned tooth crown apically. Specimens were randomly assigned to three groups for dentin conditioning with 32% phoshoric acid, two coats of bonding agents after dentin conditioning, and bond of composite resin. The surfaces of dentin were treated with etch ant and applied bonding agent, and bonded composite resin according to the directions of manufacturer. Specimens which were boned composite were sectioned longitudinally for observing interfaces between resin and dentin. Two of specimens which were sectioned longitudinally were immersed in 6 N HCL for 30 seconds and 1% NaOCL for 12 hours to partially demineralize and deproteinize the dentin substrate. Each specimen was mounted on a brass stub, sputter-coated with gold and observed under SEM. The result were as follows : 1. On the dentinal surface which was conditioned with 32% phosphoric acid. the smear layer was completely removed. orifices of dentinal tubules were opened 3-$5{\mu}m$ wide. and dentinal surface was irregular. 2. On the dentinal surface which was applied ONE-STEP. bonding agent. resin particles were observed on the orifices of dentinal tubules and intertubular dentin. 3. There were close adaptation between dentin and resin and were the pattern which composite invaded into dentin. 4. 1-$3{\mu}m$-wide hybrid layer was visible in the interface between dentin and resin. 5. Long and funnel shaped resin tags were observed in demineralized specimens. and the surfaces of tags were rough.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.154-154
• /
• 2015

현재 액체로켓 엔진 연소기 내벽은 bonding layer NiCrAlY과 Top layer $ZrO_2$가 플라즈마 용사 방식으로 형성 된다. 이는 뛰어난 열 차폐 특성과 작업시간이 짧은 장점이 있지만, bonding layer와 Top layer 사이의 열팽창 계수 차이로 인한 균열 발생 가능성이 내재 되어 있고, 연소실 내벽에 균일한 두께의 코팅층을 형성하기 어렵고 설비가 비싸다는 단점으로 인하여 세라믹 코팅 층을 금속 코팅 층으로 대체 하고자 한다. 금속 코팅층은 모재와의 밀착성이 높고, 우수한 산화 및 부식방지 기능을 가지며 저렴하다는 장점이 있다. 또한 코팅 후 연마 작업이 가능해 연소실 내부형상을 설계조건 대로 유지 할 수 있는 특징이 있다. 따라서 본 연구에서는 연소실 내벽에 적용할 모재, 무전해 Ni-P 도금과 전해 Cr 도금층 사이의 밀착력 향상을 위한 방법에 대한 연구를 하였다. 밀착력 향상을 위한 요소로 전처리 용액과 열처리 시간에 따른 영향을 알아보고자 하였으며, 이를 위해서 5가지의 산세 용액으로 각 시편을 산세 한 후, 6시간, 12시간, 18시간 열처리 하여 단면을 비교하여 열처리에 영향을 알아보고자 하였다. 연구 결과 산세 용액의 영향은 크게 나타나지 않았으며, 열처리 시간이 길수록 Ni-P/Cr의 확산이 더 잘 일어나 확산층이 더 넓어지면서 밀착력이 더 좋아 진 것으로 판단되어 진다.

• The Journal of Advanced Prosthodontics
• /
• 제5권3호
• /
• pp.226-233
• /
• 2013

PURPOSE. This study evaluated the adhesion of 10-MDP containing self-etch and self-adhesive resin cements to dentin with and without the use of etch-and-rinse technique. MATERIALS AND METHODS. Human third molars (N=180) were randomly divided into 6 groups (n=30 per group). Conventional (Panavia F2.0, Kuraray-PAN) and self-adhesive resin cements (Clearfil SA, Kuraray-CSA) were bonded to dentin surfaces either after application of 3-step etch-and-rinse (35% $H_3PO_4$ + ED Primer) or two-step self-etch adhesive resin (Clearfil SE Bond). Specimens were subjected to shear bond strength test using the universal testing machine (0.5 mm/min). The failure types were analyzed using a stereomicroscope and quality of hybrid layer was observed under a scanning electron microscope. The data (MPa) were analyzed using two-way ANOVA and Tukey's tests (${\alpha}$=.05). RESULTS. Overall, PAN adhesive cement showed significantly higher mean bond strength ($12.5{\pm}2.3-14.1{\pm}2.4$ MPa) than CSA cement ($9.3{\pm}1.4-13.9{\pm}1.9$ MPa) (P<.001). Adhesive failures were more frequent in CSA cement groups when used in conjunction with two-step self-adhesive (68%) or no adhesive at all (66%). Hybrid layer quality was inferior in CSA compared to PAN cement in all conditions. CONCLUSION. In clinical situations where bonding to dentin substrate is crucial, both conventional and self-adhesive resin cements based on 10-MDP can benefit from etch-and-rinse technique to achieve better quality of adhesion in the early clinical period.

• 한국표면공학회지
• /
• 제28권6호
• /
• pp.368-375
• /
• 1995

Thermal CVD method is in general used for the fabrication of TiC/$Al_2O_3$-coated carbide tools. The growth of TiC layer and the coating morphology depended on the chemical composition of the hard metal substrate on which the tool properties were strongly influenced. TiC-coated layer was grown by the diffusion of carbon from the substrate, whereas the growth of $Al_2O_3$ layer was unrelated to the composition of substrate. In the nitride hard coatings of Zr, Nb and Mo metals deposited on high speed steel substrate by magnetron sputtering, the reactivity of the metal elements was decreased with increasing group number in one period of the periodic system. The hard material films exhibited the highest adhesion with the chemical composition of stoichiometry or substoichiometry. The critical load as a measure of adhesion was evaluated using scratch tester. The CVD tools indicated the values of 80 and 40N in the coated layers with proper bonding to the substrate and with $\eta$ phase of 1$\mu\textrm{m}$ in the interface respectively, but the nitride films prepared by sputtering of PVD showed only the values between 10 and 20N.

• Composites Research
• /
• 제22권2호
• /
• pp.14-17
• /
• 2009

접착제에 의한 접합기술은 다양한 목적과 환경에서 널리 사용되는 방법이다. 그 중 우레탄 접착제는 액화천연가스 운반선과 같이 극저온에서 사용되는 환경에서의 접착에 사용되고 있다. 현장 적용에 있어, 본 접착제를 사용시 경화된 접착제 층의 기공들이 발생하게 된다. 본 연구에서는 우레탄 접착제와 Triplex 복합재료 접착에 있어 인공적으로 기공을 제작 삽입 후 전단응력 (Single Lap Shear) 시험을 실시하여 그 영향을 검토하였다. 실험 결과 접착력은 본 시험에서 적용한 기공의 크기 및 위치에 영향을 받지 않는다는 것을 확인하였다.

• Restorative Dentistry and Endodontics
• /
• 제28권3호
• /
• pp.209-221
• /
• 2003

The objectiveness of this study was to evaluate whether low-viscosity composite can bond effectively to dentin surface without bonding resin. The low-viscosity composites being 50wt% filler content were made by the inclusion of bonding resin of two self-etching systems(Cleafil SE Bond, Unifil Bond) varied with contents as 0, 10, 20, 30, 40, 50wt%. Exposed dentin surfaces of extracted 3rd molars are used. Dentin bond strengths were measured. The tests were carried out with a micro-shear device placed testing machine at a CHS of 1mm/min after a low-viscosity composite was filled into an iris cut from micro tygon tubing with internal diameter approximately 0.8mm and height of 1.0mm. 1 Flexural strength and modulus was increased with the addition of bonding resin. 2. Micro-shear bond strength to dentin was improved according to content of bonding resin irrespective of applying or not bonding resin in bonding procedure, and that of Clearfil SE Bond groups was higher than Unifil Bond. 3. There were no significant difference whether use of each bonding resin in bonding procedure for S-40, S-50, U-50(p＞0.05). 4. In SEM examination, resin was well infiltrated into dentin after primed with self-etching primer only for S-50 and U-50 in spite of the formation of thinner hybrid layer. Low viscosity composite including some functional monomer may be used as dentin bonding resin without an intermediary bonding agent. It makes a simplified bonding procedure and foresees the possibility of self-adhesive restorative material.

• 한국재료학회지
• /
• 제25권5호
• /
• pp.226-232
• /
• 2015

본 연구에서는 손상된 알루미늄 금형의 복원을 위해 고온플라즈마 용사법을 이용하여 금형의 표면에 $Al/Al_2O_3$ 혼합분말을 용사한 후 코팅층과 모재의 증착강도에 대한 평가를 수행하였다. 증착강도의 평가는 분사노즐의 이동속도, 순수한 알루미늄 bond coat 층의 유무에 따라 평가되었으며, bond coat 층을 생성시키지 않았을 때, 코팅층의 두께는 열팽창에 의한 잔류인장응력의 감소를 위해 두껍지 않아야 하지만 일정두께 이상이 되어야 최대의 증착강도를 얻을 수 있음이 나타났다. 또한 순수한 알루미늄 bond coat 층은 내부 결함이 없는 응고된 금속이기 때문에 두께에 따른 증착강도의 영향을 그대로 받아 두께가 두꺼울수록 bond coat 층을 생성시키지 않은 시험편보다 증착강도가 매우 낮게 측정되었다. 반면, 가장 얇게 bond coating 된 시험편 Bc3(3회의 bond coating층과 분사건의 이동속도가 20 cm/sec인 시험편) 는 bond coating을 하지 않은 시험편 중 가장 높은 증착강도를 가지는 시험편 Wbc20(bond coating층이 없고 분사건의 이동속도가 20 cm/sec인 시험편)보다 약 2배 이상증착강도가 향상되었다. 따라서 금형의 복원시에 중간층의 형성이 반드시 필요하며, 이는 코팅층의 잔류 인장응력을 보완시키며 고인성의 순수한 알루미늄과 같은 코팅층과 유사한 층을 코팅하는 것이 필요한 것으로 사료된다.

• 한국표면공학회지
• /
• 제48권6호
• /
• pp.260-268
• /
• 2015

The thermal barrier coating (TBC) for inner wall of liquid-fuel rocket combustor consists of NiCrAlY as bonding layer and $ZrO_2$ as a top layer. In most case, the plasma spray coating is used for TBC process and this process has inherent possibility of cracking due to large difference in thermal expansion coefficients among bonding layer, top layer and metal substrate. In this paper, we suggest crack-free TBC process by using a precise electrodeposition technique. Electrodeposited Ni-P/Cr double layer has similar thermal expansion coefficient to the Cu alloy substrate resulting in superior thermal barrier performance and high temperature oxidation resistance. We studied the effects of phosphorous concentrations (2.12 wt%, 6.97 wt%, and 10.53 wt%) on the annealing behavior ($750^{\circ}C$) of Ni-P samples and Cr double layered electrodeposits. Annealing temperature was simulated by combustion test condition. Also, we conducted SEM/EDS and XRD analysis for Ni-P/Cr samples. The results showed that the band layers between Ni-P and Cr are Ni and Cr, and has no formed with heat treatment. These band layers were solid solution of Cr and Ni which is formed by interdiffusion of both alloy elements. In addition, the P was not found in it. The thickness of band layer was increased with increasing annealing time. We expected that the band layer can improve the adhesion between Cr and Ni-P.