• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.2
• /
• pp.179-187
• /
• 2015

Experiments designed to measure the effect of LED (light-emitting diode) light wavelength on the growth of fingerling rockfishes (Sebastes inermis) were conducted. Fingerling rockfishes (average body weight of individual: 1.13g) were divided into two groups by wavelength of the LED light [light power: 1,620 mW; wavelength: 518 nm (green color), 622 nm (red color)]. Triplicate groups of 180 individuals were reared over 7 weeks. Lighting duration was 14 hours from 06:00 to 20:00. A water tank exposed on the natural light in a room through the windows was used as a control. At results of the first experiment [initial average body weight (BW) of individual: 1.13 g; standard deviation (SD): 0.13 g], the final individual BW exposed on the green color was increased 0.39 g than the red color, and decreased 0.12 g than the natural light in the room. At results of the second (initial individual BW: 5.07 g; SD: 0.70 g) and the third experiment (initial individual BW: 10.67 g; SD: 0.67 g), the final individual BW exposed on the green color was increased 1.07 g and 2.55 g than the red color, respectively, and increased 0.57 g and 0.84 g than the natural light, respectively. The relative growth rate of the green color was higher about 8% significantly (p<0.05) than the natural light. In the case of the red color the relative growth rate was lower significantly (p<0.05) than the natural light.

• Development and Reproduction
• /
• v.27 no.2
• /
• pp.91-99
• /
• 2023

The sea cucumber, Apostichopus japonicus, is one of the most valuable aquatic species. The color of body wall and appearance are important for the value of sea cucumbers. To examine expression pattern of long-chain acyl-coenzyme A dehydrogenase (LCAD), nuclear distribution C-containing protein 3 (NUDCD3), and receptor tyrosine kinase Tie-1 (TIE1), previously reported as differently expressed genes during the pigmentation of sea cucumber, we analyzed the temporal profiles of LCAD, NUDCD3, and TIE1 mRNAs in LED-exposed and light-shielded A. japonicus. Real-time quantitative PCR revealed that the LCAD, NUDCD3, and TIE1 mRNAs from the juveniles at 40-60 days post-fertilization (dpf) exhibited increasing patterns as compared to those of an early developmental larva (6-dpf). At 60-dpf juveniles, the LCAD and TIE1 mRNA levels of LED-exposed individuals were higher than those of light-shielded ones, whereas at 40-dpf and 50-dpf juveniles, the NUDCD3 mRNA expression was higher in the light-shielded condition (p<0.05). In the pigmented juveniles (90-dpf), the LCAD and TIE1 mRNA levels tended to show higher levels in red individuals than those in green ones, but there was a conversely higher level of NUDCD3 mRNA in green larva. In situ examination of LCAD and NUDCD3 mRNAs in light-shielded 6-dpf larva revealed that both genes are mainly expressed in the internal organs compared to the body surface. Together, these results may provide insights into the differential gene expression of LCAD, NUDCD3, and TIE1 during pigmentation process of the sea cucumber.

• The Korean Journal of Mycology
• /
• v.51 no.2
• /
• pp.69-80
• /
• 2023

The cultivation conditions of shiitake mushrooms (Lentinula edodes) influence the production and quality of fruiting bodies. We conducted this study to improve the productivity and quality of shiitake mushrooms by modifying the cultivation conditions. Two types of spawns (sawdust and liquid spawn) were used, and corn flour was used as a nutritional source for the sawdust medium. A blue light-emitting diode (LED; 300 lux) was also used instead of a white LED during the incubation period. Sanbaekhyang was used as the experimental variety. When using corn flour, the mycelial growth rate increased 1.1 to 2.7 times the growth rate of the control up to 21 days of incubation, and the weight loss rate of the media was also higher. Mushroom productivity increased 1.2 times when the liquid spawn was used compared to when the sawdust spawn was used, and the blue LED also increased fruiting body production by 1.1 times compared to the white LED. Mushroom productivity increased when the liquid spawn was used, and the blue LED also increased fruiting body production. Fruiting body weight and the size of the cap were greater when sawdust spawn was used. The fruiting body weight and the stipe diameter were greater when the blue LED was used. Taste analysis showed that the saltiness increased when corn flour was used, and the sourness increased when the blue LED was used.

• ETRI Journal
• /
• v.37 no.1
• /
• pp.97-106
• /
• 2015

In this paper, MOS-triggered silicon-controlled rectifier (SCR)-based electrostatic discharge (ESD) protection circuits for mobile application in 3.3 V I/O and SCR-based ESD protection circuits with floating N+/P+ diffusion regions for inverter and light-emitting diode driver applications in 20 V power clamps were designed. The breakdown voltage is induced by a grounded-gate NMOS (ggNMOS) in the MOS-triggered SCR-based ESD protection circuit for 3.3 V I/O. This lowers the breakdown voltage of the SCR by providing a trigger current to the P-well of the SCR. However, the operation resistance is increased compared to SCR, because additional diffusion regions increase the overall resistance of the protection circuit. To overcome this problem, the number of ggNMOS fingers was increased. The ESD protection circuit for the power clamp application at 20 V had a breakdown voltage of 23 V; the product of a high holding voltage by the N+/P+ floating diffusion region. The trigger voltage was improved by the partial insertion of a P-body to narrow the gap between the trigger and holding voltages. The ESD protection circuits for low- and high-voltage applications were designed using $0.18{\mu}m$ Bipolar-CMOS-DMOS technology, with $100{\mu}m$ width. Electrical characteristics and robustness are analyzed by a transmission line pulse measurement and an ESD pulse generator (ESS-6008).

• Journal of Electrical Engineering and Technology
• /
• v.12 no.6
• /
• pp.2278-2288
• /
• 2017

Multilevel converter topologies are widely used in many applications. The cascaded H-bridge multilevel inverter (CHBMI), which is one of many multilevel converter topologies, has been introduced as a useful topology in high and medium power. However, it has a drawback to require a lot of switches. Therefore, the reliability of CHBMI is important factor for analyzing the performance. This paper presents a simple switch fault diagnosis method for single-phase CHBMI. There are two types of switch faults: open-fault and short-fault. In the open-fault, the body diode of faulty switch provides a freewheeling current path. However, when the short-fault occurs, the distortion of output current is different from that of the open-fault because it has an unavailable freewheeling current flow path due to a disconnection of fuse. The fault diagnosis method is based on the zero current time analysis according to zero-voltage switching states. Using the proposed method, it is possible to detect the location of faulty switch accurately. The PSIM simulation and experimental results show the effectiveness of proposed switch fault diagnosis method.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.1891-1901
• /
• 2017

In this paper, optimal control of the fuel cell and design of a high-efficiency power converter is implemented to build a high-priced fuel cell system with minimum capacity. Conventional power converter devices use a non-isolated boost converter for high efficiency while the battery is charged, and reduce its conduction loss by using MOSFETs instead of diodes. However, the efficiency of the boost converter decreases, since overshoot occurs because there is a moment when the body diode of the MOSFET is conducted during the dead time and huge loss occurs when the dead time for the maximum-power-flowing state is used in the low-power-flowing state. The method proposed in this paper is to adjust the dead time of boost and rectifier switches by predicting the power flow to meet the maximum efficiency in every load condition. After analyzing parasite components, the stability and efficiency of the high-efficiency boost converter is improved by predictive compensation of the delay component of each part, and it is proven by simulation and experience. The variation in switching delay times of each switch of the full-bridge converter is compensated by falling time compensation, a control method of PWM, and it is also proven by simulation and experience.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.10
• /
• pp.1-8
• /
• 2013

Wireless Visible Light Communication is the technology that enables communication using LED illumination Infrastructure instead of existing illumination such as incandescent lamp or fluorescent light. Because VLC uses light for communication, it has no problem of frequency permission and is harmless to human body. It is also possible to check the communication through eye. So VLC can be used as a supplement to the Radio Frequency communication, Infrared in indoor environment. So far, researchers on the LED Visible light communication have focused on the increasing transmission speed, transmission distance, modulation method. However, there is few research of main factors that influence on system performance. System performance has been mainly predicted through simulation. In this paper, I recognized that these factors such as outside light noise, obstacle, LED panel position or emitted angle have a great impact on wireless communication system. So I experimented VLC system by changing distance and position to discover location suitable for BER regulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.202-205
• /
• 2005

The purpose of this work is to identify the characteristic of eye movement for visual training of the elderly. This investigation is to examine the relationship between the head and the eye motor system for the localization of visual target direction in three-dimensional space. All experiments were performed in a soundproof chamber. Twenty-one red LEDs (Light-Emitting Diode, Brightness: 20cd/$m^2$) arrayed in three lines on a half circle-surrounding panel are used. LEDs are horizontally 30 degree apart and vertically 20 degree apart from each other. The condition of stimulation is random and anti-saccade. Physiological parameter such as EOG (Electro-Oculography) was measured by BIOPAC system. We measure the mean latency time, which is the time from the start of visual stimulation to the response of the human body. The result shows that the mean latency time is short in the case of the condition of anti-saccade, the fixed head and a quarter visual stimulation. This finding can be used in developing programs for various visual improvements for the elderly by analyzing the characteristic of eye movement.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.5
• /
• pp.226-229
• /
• 2010

Many methods exist that promote wound healing, including light therapy, which consists of light beams that assist the human body in treating and sterilizing wounds, as well as regenerating cells. Irradiation with specific wavelengths of either laser or LED light has been shown to induce beneficial proliferation of fibroblasts that, depending on the size of the wound, can be effective in promoting wound healing. The experiments in this study utilized 8 week old 250~300 g Male Sprague Dawley Rats (ILAR Code: NTacSam:SD) and included a non-irradiation group and a 525 nm green LED irradiation group (n of each group = 7). In experiments animals were allowed to rest for 24 hours after wounds had been excised, which was followed by non- irradiation or 525 nm green LED irradiation therapy one hour per day for 9 days. Immunohistochemical staining was conducted for cytokeratin in order to precisely measure the defect size. In addition, Masson's trichrome staining was utilized in order to compare levels of collagen between the 525 nm green LED irradiation group and the non-irradiation group. Animals exposed to 525 nm green LED irradiation (p<0.05) healed at a faster rate and had increased collagenosis compared with the non-irradiated control group. Thus, treatment with 525 nm green LED irradiation had a beneficial effect on wound healing and should be considered as a possible alternative to low power laser treatment.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.5
• /
• pp.141-148
• /
• 2013

There are several problems in the conventional 2-D image processing and 3-D measurement systems. In the case of the 2-D image processing system, it is not possible to detect elevation data. In a 3-D measurement system, it requires a skillful operator and a lot of time for measuring data. Also, there exist data errors depending on operators. The limitation of detecting elevation data in the 2-D image processing system can be solved by laser diodes. In this study an algorithm that measures the accurate data in a subject face to be detected by combining laser diodes and a commercial CCD camera is developed. In the development process, a planar equation is developed using laser diodes and the equation is used to obtain a normal vector. Based on the results, an algorithm that transforms commercial CCD camera coordinates to 3-D coordinates is proposed. The completed measurement method will be applied to replace a manual measurement system for vehicle bodies and parts by an automated system.