• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.131-131
• /
• 2017

• Bulletin of the Society of Naval Architects of Korea
• /
• v.25 no.1
• /
• pp.3-10
• /
• 1988

This paper presents some experimental investigations on the effectiveness of the Stern-End-Bulb(SEB) and the design procedure of the optimum one. Experimental method was discussed to search the optimum SEB and the resistance reduction rate was investigated from the resistance test results of the SEB series for a passenger boat and a container ship. The contribution of SEB on the propulsive coefficients was discussed from the self-propulsion test results for a container ship. It would be expected that the power saving rate is about 5.8 percents for a passenger boat and 3.6 percents for a container ship by optimum SEB, respectively.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.534-541
• /
• 2007

This paper suggests the mathematical method for the estimation of the required engine output for WIG crafts. The engine size of a WIG craft Is a key parameter in the design stage, because WIGs should overcome the hump drag during the take-off. Therefore, it is very important for a WIG designer to estimate required power and state change during take-off. The mathematical method was developed based on the steady planing state model of a planing boat. Through numerical calculations on various take-off states, it was found that the suggested method could give reasonable estimation of required power and state change during take-off.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.221-224
• /
• 2003

This study was carried out to develope a basic form of planning hull type fishing boat. G/T 10ton class is selected as object hull form, and hull form is designed in Chosun University. A series of test results of LCG variations for 5 different LCG points are presented in this paper. The test was performed in Davidson Laboratory, and the scope of tests include resistance, trim and sinkage.

• 한국기계연구소 소보
• /
• s.13
• /
• pp.87-98
• /
• 1984

An experimental study carried out to predict the performance characteristics of a high speed planing boat at the two displacements whose hull form shows hard chines form transom to bow. In the resistance test the planing hull model was porpoising at and above 30 knots for both displacements of 30 tons and 24 tons. A small stern wedge was newly designed and attached across hull bottom. The planing hull model with the stern sedge did not show any porpoising up to the speed of 45 knots for both displacements and it analysed results shows the improvement of resistance performance and planing performance comparing with those of original hull form; i.e. for displacement of 30 tons the effective power and trim angle were reduced by 18.9% and 5.71 degrees at the speed of 28 knots, and for the displacement of 24 tons the effective power and trim angle were reduced by 23.63% and 4.37 degrees at the speed of 28 knots, respectively.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.4
• /
• pp.390-397
• /
• 2012

According to sailing condition, an exciting force for luminairie of naval vessels was measured and analyzed. A naval combat service support boat and P${\bigcirc}{\bigcirc}$(patrol killer guided missile) were selected as a target naval vessel. Due to their small size and fast speed, they received excessive vibration than other bigger naval vessels like destroyer. The vibration of luminairie was measured on their cruising and maximum speed. This could analyze exciting force for luminairie of naval vessels. Using this analyzed data, the validity of military standard for naval vessel was verified.

• Journal of the Korean Institute of Navigation
• /
• v.23 no.4
• /
• pp.21-28
• /
• 1999

In some cases a towing vessel and her tow, a fishing boat, and a vessel at anchor have a priority against a general power-driven vessel underway in the application of collision rule. This article aims at suggesting a practical guide for the construction of the meaning of a vessel engaging in fishing, a vessel engaged in towing operation such as severely restricts the towing vessel and her tow in their ability to deviate from their course and a vessel at anchor, which are permitted to have the above priority. The construction of the application of the collision rule on the above vessels is supported by the decisions of MAIA and the judgment of civil courts.

• Journal of the Korean Institute of Navigation
• /
• v.19 no.1
• /
• pp.1-8
• /
• 1995

The motion of a small boat in seas is affected in relatively higher degrees than the case of a larger ship by the specific characteristics of sea waves, i.e., the wave length and height. Ship's motion caused by sea waves is a matter of special importance to small fishing boats, because they carry out fishing job in rough seas frequently. This is an experimental study on the rolling and pitching motions of full scale ship. In the experiment, the ship's motions were measured for head, how, beam, quarter and following seas. The experiment were carried out on board the training ship Pusan 404(160 GT) in the adjacent waters off NAM HYENG JAE DO on Dec. 13th 1994. The sea condition during the measurements was that wave height 2.5m, no swell and the wind velocity of 12 m/sec. Some statistic considerations were given to the observed data by the series analysis methods and discussed in this paper.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.6
• /
• pp.112-118
• /
• 2013

This paper reports the results of a comparative study on rudder performance between the steel rudders that have been used in coastal angling fishing boats in the 20-GT class and the newly developed FRP composite material rudders. In order to compare the rudder performances of these two types, a sea trial test was carried out to investigate the speed performance, fuel consumption, and ship's turning ability. The results showed that the sea trial performance of the FRP composite rudder was better than that of the steel rudder type in terms of the sea speed, fuel consumption rate, and turning ability.

• Journal of Ship and Ocean Technology
• /
• v.9 no.3
• /
• pp.14-22
• /
• 2005

A 12 m long G/T 4.99 Class Trimaran is now under development at the Center for Transportation System of the Yellow Sea (CTYS) before deployed as a pleasure fishing boat along the west coast of Korean peninsula. The boats will be made of fiber reinforced plastics and equipped with a 360 hp diesel engine and a water jet propulsion system to propel the ship to reach maximum speed of 25knots after fully loaded. Model tests for hull form development of the Trimaran have been done at the towing tank of the Inha University. The influence of the spacing between main hull and outriggers and the longitudinal location of the outriggers have been carefully examined to find the optimal size and locations of the outriggers to improve both the resistance characteristics, and the results are reported in the present paper.