• 한국항공우주학회지
• /
• 제32권8호
• /
• pp.47-53
• /
• 2004

타원형 날개꼴의 공력 특성에 브로잉 제트 방식과 제트 방향의 영향에 대하여 실험을 통하여 연구를 수행하였다. 본 연구는 타원형 날개꼴의 박리제어에 있어서 브로잉 제트적용에 관한 기본 데이터를 축적하는데 목적을 두었다. 본 연구에서는 날개면에서의 압력 분포, 브로잉 제트 출구에서의 유속 분포 및 공력 자료를 제공하였다. 타원형 날개꼴에 대한 실험은 레이놀즈수 $8.22{\times}10^5$에서 수행하였다. 펄스제트는 후실속각 이후에 공력 특성을 향상시키는 효과를 보여 주었다. 즉, 펄스제트는 감소된 질량유동율로 상당히 높은 양력을 발생하였다. 제트 방향도 박리제어의 주요 파라미터임을 보였다. 양의 제트각은 박리를 지연시키거나 억제하였고, 음의 제트각은 박리를 오히려 촉진시켰다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 추계 학술대회논문집
• /
• pp.115-119
• /
• 2004

The effect of a continuous blowing or suction on an oscillating 2-D NACA0012 airfoil was investigated numerically for the dynamic stall control. The influence of control parameter variation was also studied in the view point of aerodynamic characteristics. The result showed that the blowing control kept a higher lift drag ratio before stall angle but the dynamic stall angle was not exceed to without control result. As the slot position was closer to leading edge, the positive control effect becomes greater. The stronger jet and the smaller jet angel made more favorable roles on the control performance. In the cases of the suction, the overall control features were similar to those of the blowing, but dynamic stall angle was increased, i.e. suction was more effective to control dynamic stall. It was also founded that the suction control was showed better control effect as the slot position moves to trail edge within thirty percentage of chord length. In the simulation for the jet strength and the jet angle control, the same tendencies were observed to those of blowing cases.

• 대한기계학회논문집B
• /
• 제23권5호
• /
• pp.577-586
• /
• 1999

Two problems with jet injection through the cylindrical film cooling hole are 1) penetration of jet into mainstream rather than covering the surface at high blowing rates and 2) nonuniformity of the film cooling effectiveness in the lateral direction. Compound angle injection is employed to reduce those two problems. Compound angle injection increases the film cooling effectiveness and spreads more widely. However, there is still lift off at high blowing rates. Shaped film cooling hole is a possible means to reduce those two problems. Film cooling with the shaped hole is investigated in this study experimentally. Film cooling hole used in present study is a shaped hole with conically enlarged exit and Inlet-to-exit area ratio is 2.55. Naphthalene sublimation method has been employed to study the local heat/mass transfer coefficient and film cooling effectiveness for compound injection angles and various blowing rates around the shaped film cooling hole. Enlarged hole exit area reduces the momentum of the jet at the hole exit and prevents the penetration of injected jet into the mainstream effectively. Hence, higher and more uniform film cooling effectiveness values are obtained even at relatively high blowing rates and the film cooling jet spreads more widely with the shaped film cooling hole. And the injected jet protects the surface effectively at low blowing rates and spreads more widely with the compound angle injections than the axial injection.

• International Journal of Aeronautical and Space Sciences
• /
• 제9권1호
• /
• pp.111-120
• /
• 2008

A particle image velocimetry (PIV) technique was employed to investigate the effects of blowing jet on the flow characteristics over stationary and pitch-oscillating airfoils. The Reynolds number was $7.84{\times}10^5$ based on the chord length. It was found that for stationary airfoil cases, continuous and pulsating blowing jets successfully reduced separated wake region at high angles of attack. A comparison study of two different types of jet blowing indicated that pulsating jet is more effective than continuous jet for flow separation control. Pulsating leading-edge blowing postpones flow separation and increased stall angle of attack by $2^{\circ}{\sim}3^{\circ}$. For pitch-oscillating airfoil cases, the PIV results showed that blowing jet efficiently delays the separation onset point during pitch-up stroke, whereas it does not prevent flow separation during pitch-down stroke, even at angles of attack smaller than static ones.

• 한국항공우주학회지
• /
• 제35권12호
• /
• pp.1059-1066
• /
• 2007

타원형 단면 에어포일의 블로잉 제트에 의한 유동박리 제어효과에 대한 연구를 레이놀즈수 Rec=7.84×105에서 실험적 방법으로 수행하였다. 블로잉 제트는 에어포일 내부의 공기실에 있는 압축공기를 앞전 혹은 뒷전에 위치한 좁은 제트슬롯을 통하여 분출시켰다. 실험결과 블로잉은 날개면 압력회복으로 수직력을 증가시킴으로써 박리 유동을 제어할 수 있음을 보였다. 블로잉에 의한 수직력의 상승은 상대적으로 높은 받음각에서 더욱 효과가 컸으며 낮은 받음각에서는 감소되었다. 현 연구조건에서 수직력을 상승시키는데 가장 효과적인 블로잉 방식은 앞전에서의 90° 방향의 간헐제트이었다. 특히, 간헐제트가 부여된 경우 실속 받음각을 약 2°-3° 지연시킬 수 있었다. 연속제트와 간헐제트 모두 에어포일의 공력특성과 성능을 향상시킴으로써 유동박리 제어에 직접적이고 유효한 방법임을 입증하였다.

• 대한기계학회논문집B
• /
• 제32권4호
• /
• pp.283-289
• /
• 2008

An experimental investigation was conducted to investigate the heat/mass transfer for impingement/effusion cooling system with inclined jet. Jets with inclined angle of 60 are applied to impingement/effusion cooling. At the jet Reynolds number of 10,000, the experiments were carried out for blowing ratios ranging from 0.0 to 1.5. The local heat/mass transfer coefficients on the effusion plate are measured using a naphthalene sublimation method. The result indicates that the inclined jet causes the non-uniform and low heat/mass transfer compared to the vertical jet. At stagnation region, the peak position is shifted from the geometrical center of injection hole due to Coanda effect and its level is higher than that of vertical jet due to increase in turbulence intensity by steep velocity gradient near the stagnation region. Further, the secondary peak region disappears because the interaction between adjacent wall jets weakens. When the initial crossflow occurs, the distorted heat/mass transfer pattern appears. As the blowing ratio (crossflow rate) increases, the heat/mass transfer distributions become similar to those of the vertical jet. This is because the effect of crossflow is dominant compared to that of inclined jet under high blowing ratio $(M{\geq}1.0)$. At low blowing ratio $(M{\leq}0.5)$, averaged Sh value is 10% lower than that of vertical jet, whereas its value at high blowing ratio $(M{\geq}1.0)$ is similar to that of vertical jet.

• 설비공학논문집
• /
• 제22권2호
• /
• pp.57-63
• /
• 2010

Air curtains are widely used for gates of shopping mall, warehouse, cold stores and refrigerated display cabinets. The purpose of the air curtain is to reduce the infiltration of outdoor air and heat loss from the air conditioning space to ambient air. The discharge angle of air curtain is very important as the sealing efficiency is affected by it. This paper presents a performance of single jet air curtain in heating space when the discharge angle of nozzle changes. A numerical simulation is used to study the influence of various parameters on the efficiency of the downward-blowing air curtain device which is installed inside of the wall above the door. The performance of the air curtain is evaluated by sealing efficiency which provides the assessment of the energy savings. A condition of discharge angle that has the highest sealing efficiency is proposed.

• 한국항공우주학회지
• /
• 제34권5호
• /
• pp.1-11
• /
• 2006

본 연구에서는 연속적 블로잉 요소들의 변화가 낮은 레이놀즈 수를 가지는 유동장에서 NACA 0015 익형 주위의 유동제어 및 익형의 실속제어에 미치는 영향에 대하여 비정렬 격자계를 사용하는 수치적 기법을 이용하여 살펴보았다. 실속 이전의 받음각들에서 연속적 블로잉 요소들의 변화에 따른 공력계수 및 모멘트 계수의 변화를 통하여 각 요소들의 유동제어 효과를 살펴보았으며, 각 요소들의 변화에 따른 실속각의 변화를 통하여 실속제어 효과를 살펴보았다. 실속이전의 받음각에서 비교적 강한 세기의 블로잉을 수행하면 항력의 증가를 동반한 양력의 증가가 나타났다. 앞전부근에서의 적절한 세기의 연속적 블로잉은 실속이전의 각에서 양력의 증가를 나타내고, 실속제어 특성을 보였다. 블로잉 제트의 방향이 유동제어를 하지 않았을 때의 블로잉 슬롯 주변 유동의 방향과 일치하는 경우가 가장 좋은 유동제어 특성을 나타냄을 알 수 있었다.

• 한국항공우주학회지
• /
• 제30권3호
• /
• pp.17-26
• /
• 2002

훈련기의 1/12 축소 날개반쪽 모델 및 1/16 축소 완제기 전체모델에 날개끝 불어내기 방향이 다른 3가지 슬롯(전방 35도 방향, 날개방향, 후방35도 방향)을 장착하고, 또한 3가지 불어내기 운동량 계수 (0. 004, 0.009, 0.017)의 변화를 받음각의 증가에 따라 양력과 항력의 공력특성의 변화를 비교하였고, 반쪽모델에서는 전체모델과 같은 방법으로 날개 윗면의 압력을 측정하여 기본형과 비교하였다. 실험결과 날개방향으로 불어내기를 하였을 경우와 불어내기 운동량 계수가 0.017인 경우가 가장 큰 항력감소와 양항비의 증가를 나타냈으며, 받음각 8도에서 가장 큰 항력감소율과 양항비 증가율이 있었음을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제27권10호
• /
• pp.1472-1479
• /
• 2003

An attempt to reduce supersonic jet noise is carried out by using two steady microjets in a round jet. The jet is issued from a round sonic nozzle with an exit diameter of 10 mm. Two micro-nozzles with an inside diameter of 1 mm each are installed on the exit plane at an angle of 45 relative to the main jet axis. Far-field noise was measured at 40 diameters off the jet axis. The angle between a microphone and the jet axis is 30 or 90$^{\circ}$. For an injection rate of 4-6% of the main jet, screech tones were completely suppressed by the microjets. The reduction in the overall sound pressure levels were 2.4 and 2.7 dB for 90 and 30 measuring directions, respectively. However, the enhancement of mixing/spreading of the jet by the microjet was negligible. The reduction of noise is probably due to distorted shock cell structures and/or deformed large scale vortical structures by the microjets.