• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.233-236
• /
• 2004

An experimental study was conducted to evaluate characteristic variation of diluted engine oil by diesel fuel and its effects on engine components. Especially, engine oil was made to have $15\%$ fuel content. To predict existing diesel fuel content in engine oil after test was used the viscosity calibration curve. About $54\%$ percent of diesel fuel in diluted engine oil was distillated by various paths related to reciprocating motion of piston and the rest diesel fuel plays an important role for decreasing engine oil viscosity. Test results show that lowered engine ell viscosity by diesel fuel dilution become a reason of increasing engine elements wear, Therefore, this caused the quantity of blow-by gas to increase and main gallery pressure to decrease.

• 한국항공운항학회지
• /
• 제23권4호
• /
• pp.36-41
• /
• 2015

The cyclone separator is a simple device, which causes the centrifugal separation of materials such as droplets or particles in a fluid stream. The cyclone separator utilizes the energy obtained from fluid pressure and linear motion to create rotational fluid motion. This rotational motion leads the materials suspended in the fluid to separate from the fluid quickly due to the centrifugal force. The rotation is produced by the tangential or involuted introduction of fluid into the vessel. These materials may be droplets of fuel in blow-by gas through an engine. Droplets suspended in the feed liquid may separate according to size, shape, or density. And the change of part dimension in a cyclone separator can yield the its performance variation. The current study shows the influence of design parameters on the performance of a cyclone separator for blow-by gas.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.213-216
• /
• 2009

가스터빈 연소기의 화염 특성을 알기 위하여 분할 연소기 시험을 수행하였다. 점화시험은 여러 가지 연소기 유입 공기속도와 공기과잉율에 따라 토치 점화장치를 이용하여 수행되었다. 또한, 연료를 충분히 공급한 상태에서 점화를 수행한 후 점차 연료량을 감소시켜가며 희박연소한계를 측정 하였다. 실험 결과, 공기과잉율 6에서 안정한 점화를 보였고 이 값은 연소기 공기 유입속도에 따라 점점 증가함을 보였다. 최소 실화한계는 연소기 공기 유입속도 40 m/s에서 약 4였고, 이 값 또한 연소기공기유입속도에 따라 약 10 까지 증가함을 보였다.

• 한국주조공학회지
• /
• 제18권5호
• /
• pp.481-487
• /
• 1998

Shell sand is widely used to make a complex shape castings due to its good collapsibility. When molten metal is poured into the mold, various gases are generated by the thermal decomposition of binder in the shell core. Casting defects such as blow hole and blister come from these gases. If it is possible to predict the evolution of gas quantitatively, it may provide effective solutions for minimizing the casting defects. To examine the gas evolution by shell core quantitatively, casting experiment and calculation were carried out. Gas pressure and gas volume evolved by shell core were measured in the experiment, and temperature distribution in the shell core was obtained by heat transfer analysis. From the result above, prediction on the gas volume evolved during pouring was tried. As forming pressure of the shell core increased and forming temperature decreased, the gas evolution increased. There was a close relationship between the calculated gas volume evolved and the measured one.

• 한국가스학회지
• /
• 제11권4호
• /
• pp.59-63
• /
• 2007

The purpose of this paper is to find optimum vent port of the booth for gas explosion experiment. Also, it is to understand the safety of the booth for explosion experiment which is installed to let the trainees for legal education which is managed by IGTT(Institute of gas technology training) blow the riskiness of explosion. Since the booth for gas explosion experiment is a confined space, we used the exhaust model for indoor explosion. As the result, it was safety calculated when the amount of leaking gas was close to the maximum of explosion limit on the explosion experiment.

• 한국분무공학회지
• /
• 제25권4호
• /
• pp.162-169
• /
• 2020

The worldwide focus on reducing the emissions, fuel and lubricant consumption in T-GDI engines is leading engineers to consider the crankcase ventilation and oil mist separation system as an important means of control. In today's passenger cars, the oil mist separation systems mainly use the inertia effect (e.g. labyrinth, cyclone etc.). Therefore, this study has investigated high efficiency cylinder head-integrated oil-mist separator by using a compact multi-impactor type oil mist separator system to ensure adequate oil mist separation performance. For this purpose, engine dynamometer testing with oil particle efficiency measurement equipment and 3D two-phase flow simulation have been performed for various engine operating conditions. Tests with an actual engine on a dynamometer showed oil aerosol particle size distributions varied depending on operating conditions. For instance, high rpm and load increases bot only blow-by gases but the amount of small size oil droplets. Submicron-sized particles (less than 0.5 ㎛) were also observed. It is also found that the impactor type separator is able to separate nearly no droplets of diameter lower than 3 ㎛. CFD results showed that the complex aerodynamics processes that lead to strong impingement and break-up can strip out large droplets and generate more small size droplets.

• Tribology and Lubricants
• /
• 제21권4호
• /
• pp.159-164
• /
• 2005

An experimental study was conducted to evaluate characteristic variation of diluted engine oils in which contains diesel fuels and its tribological effects on engine components. In this study, diluted engine oils with $10\%,\;15\%,\;and\;20\%$ of initial fuel content rate have been used for measuring the viscosity reduction rate, blow-by gas increment rate, main gallery pressure reduction rate, and fuel content rate in engine oils. These parameters are strongly related to the tribological characteristics of key engine components. The kinematic viscosity of engine oils in which is contained by diesel fuels from $10\%\;to\;20\%$ in oils is decreasing to approximately $54\%$ of initial diluted fuel-oil volume ratios. The experimental results show that the distillated engine oil decrease the viscosity of engine oil and its oil film stiffness, and increase the wear rate of rubbing parts of engine components. Thus we recommend that the containing volume rate of fuels in engine oils should be restricted to $3\~4\%$ for a sophisticated Diesel engine and $5\~7\%$ for a standard one.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.166-174
• /
• 1998

The distribution of oil film thickness in piston were measured by induced fluorescence method. A Xe lamp was used as light source. Coumarine-6 was mixed with oil as the fluorescent dye. Fluorescent signal which is proportional to the oil film thickness was acquired by CCD camera and transmitted to the personal computer as video signal. In order to solve the problem of measurement system, irregular distribution and unstability of light intensity, as well as to know the relationship between the oil film thickness and output signal, three different calibration techniques were used. Motoring and firing tests were performed in a single cylinder research engine with transparent liner. By analyzing the oil film thickness converted from the photographed image, it was observed that each of three piston rings scrapes the oil both upward and downward and oil film thickness is not uniform horizontally at a given piston land. The amount of oil in each land was considerably affected by the engine load. It is thought that the blow-by gas blows the oil down to the crankcase.

• 오토저널
• /
• 제8권4호
• /
• pp.1-12
• /
• 1986

대기오염의 역사는 산업의 발전과 그 맥락을 같이 한다. 자동차가 대기오염의 한 Source로 주목 을 받기 시작한 것은 1940년대초 LA의 극심한 Smog발생의 원인을 찾으면서 부터이며, 1950년대 에 와서 Haagen Smit박사에 의해 Photo Smog의 Mechamism이 해석되면서 Smog를 유발하는 HC, NOx는 자동차 배출 Gas가 50% 이상을, 유해한 CO는 90%이상을 기여한다는 것이 파명되 어, 1965년 미국 California주에서 자동차에 대한 배출 Gas규제가 최초로 시작되었다. 자동차 배출 Gas로서 규제대상은 HC(타화수소), CO, NOx(질소산화물)이며, 엔진 Crankcase Emission(Blow-by Gas), Tail pipe로부터 배출되는 Exhaust Emission, 그리고 연료 Tank, 기 화기등의 연료계로부터 배출되는 Evaporative Emission에서의 HC, CO, NOx 각 상한치를 규제 하고 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.799-803
• /
• 2008

The possibility of manufacturing titanium hollow cylinder tank for ramjet engine was demonstrated with superplastic forming of subscale article. An innovative manufacturing method to produce complex configuration from titanium multi-sheets by low hydrostatic pressure was presented. Finite element analysis on superplastic blow forming process has been carried out in order to improve the forming process when manufacturing subscale hollow cylinder structure using Ti-6Al-4V multi-sheets. The simulation focused on the reduction of forming time and obtaining finally required shape throughout investigating the deformation mode of sheet according to the forming conditions and die geometry. From pre-sized titanium sheets, near net shape of hollow cylinder tank is obtained by superplastic blow forming conducted using gas pressure of 15bar at 1148K. The result shows that the manufacturing method with superplastic forming of multi-sheets of titanium alloy has been successful for near net shape forming of subscale hollow cylinder tank of ramjet engine.