• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.3026-3031
• /
• 2008

In conventional closed-loop crankcase ventilation systems, the lubrication oil had to be re-circulated to the intake manifold, in the form of oil mist mixed with the blow-by gas. This blow-by gas containing the engine lubricant oil affects on the engine problems and the exhaust emissions. A high-efficient oil separator is required to minimize consumption of engine oil and reduce harmful emissions. In the conventional oil separator of CI engines, it has good oil separation performance even though separator design is simple, due to lots of the blow-by gas. As the emission regulation becomes severe, the oil separator for SI engines is also required. But in SI engines, separator design should be optimized, due to small size of oil particles and little amount of blow-by gas. In this study, oil separation performance classified by diameter of oil mist in cylinder head cover internal model which has three cyclones and two baffle plates for SI engine is calculated with CFD methodology.

• International Journal of Automotive Technology
• /
• 제8권2호
• /
• pp.219-224
• /
• 2007

Recently, atmospheric contaminations has become worse due to the increased number of automobile. The PCV (Positive Crankcase Ventilation) valve acts as a flow control to allow re-combustion of blow-by gas by having it flow from a crankcase to an inlet manifold suction tube. Also, during the fabrication of the PCV valve, micro cracks may occur in the valve body and be extended under operation. The excessive stress distribution and crack initiation on the PCV valve body would bring an unstable blow-by gas flow rate control and would cause valve failure. The purpose of this study is to examine the crack affects on the stress and strain variations on the PCV valve according to the inlet and outlet manifold under differential pressures. From the results, we can explain the behavior of the crack extension for a safe condition of PCV valve.

• 한국기계가공학회지
• /
• 제19권4호
• /
• pp.36-44
• /
• 2020

This study analyzed the deformation behavior of the high density polyethylene (HDPE) bottle in the blow molding process. We carried out finite element (FE) simulations using ANSYS Polyflow. First, the axisymmetric model was executed by 2D FE-simulation to determine the change of bottle wall thickness during the molding process. Then, the square model of the bottle was executed by 3D FE-simulation to gauge the effects of gas pressure on the change of wall thickness. The experiment results showed that the FE-simulations were able to upgrade the quality of the HDPE bottle in the blow molding process. These results can be used as guidance in adjusting gas pressure, as well as be extended for further study to determine process parameters such as temperatures, forming velocity, parison shape, etc.

• 드라이브 ㆍ 컨트롤
• /
• 제14권3호
• /
• pp.32-39
• /
• 2017

In this study, a mathematical model of the pneumatic part in a gas blow-down system is proposed. The mathematical model consists of four major parts: pressure vessel, reservoir, pressure regulator and pipe-line. To ensure accuracy in long-time simulations, heat transfer between gas and pressure vessel is considered. The model is validated by comparing simulation results with experimental data. Experiments are conducted on the ground, where free convection can be assumed. Simulation results indicate the proposed model can accurately describe behavior of a gas blow-down system. Therefore, it may be used for design and analysis of similar systems with a slight modification.

• 드라이브 ㆍ 컨트롤
• /
• 제13권3호
• /
• pp.1-7
• /
• 2016

A cold gas blow-down hydraulic actuation system is widely used in missiles that require an actuation system with a fast response time under a limited space with a short operating time and large loads on the actuators. The system consists of a pneumatic part that supplies the regulated high-pressure gas to a reservoir, and a hydraulic part that supplies pressurized hydraulic oil to the actuators by the pressurized gas in the reservoir. This paper proposes a mathematical model to analyze and simulate the pneumatic part of an actuation system that supplies the operating power to the actuators. The mathematical model is based on the ideal gas equation and also considers the models for heat transfer. The model is applied to the pressure vessel and the gas part of the reservoir, and the model for the pneumatic part is established by connecting the two models for the parts. The model is validated through a comparison of the simulation results with the experimental results. The comparison shows that the suggested model could be useful in the design of the pneumatic part of a cold gas blow-down type hydraulic actuation system.

• Tribology and Lubricants
• /
• 제25권5호
• /
• pp.311-317
• /
• 2009

To satisfy the more severe emission regulation and the demand of higher fuel economy in near future, the combustion pressure and power output of engines is going to be higher. In order to get the reduction of engine emission and the higher power, it is needed the reduction of the tension and width of ring pack. The lower tension ring and the thinner width ring can bring not only the friction reduction between the ring and liner during engine running, but also the adjustment of the blow-by gas and oil consumption by changing in the pressure in the crevice volume and the axial motion of rings togethe with the adjustment of the inter-ring crevice volumes. In this study, by using a developed basic computer proglram that predicts the blow-by gas and oil consumption of engines, it is to be examined how satisfying the level of the blow-by gas and oil consumption as being installed the piston ring pack with thinner width ring and lower tension ring.

• 한국산학기술학회논문지
• /
• 제16권8호
• /
• pp.5082-5088
• /
• 2015

본 논문에서는 1000cc급 엔진의 내구성능 시험을 진행하였다. 총 300시간의 내구 시험이 WOT조건으로 진행되었다. 엔진토크, 출력, 제동연료소비율, 블로바이 가스량, 오일압력 등을 시간에 따라 계측하였다. 실험결과, 고 rpm에서의 성능은 시간에 따라 감소하였으나, 저 rpm에서의 성능은 안정적이었다. Blow-by gas 유량은 평균 흡입 공기량의 0.4%로 우수한 성능을 나타내었다. 엔진의 토크와 연료소모율은 100시간까지는 길들이기 특성을 보였으며, 그 이후에 노화되는 경향을 보였다. 300시간 내구시험 후 엔진을 분해하여 부품의 파손 및 균열 여부를 확인하였다.

• 한국자동차공학회논문집
• /
• 제24권5호
• /
• pp.549-555
• /
• 2016

This research was performed to determine the oil separation characteristics of the specially designed oil filter installed in a PCV cylinder head passage. The oil filter was specially designed with fleece for separating oil mist from blow-by gas. The fleece, made of fiber fabric material, is placed in the oil filter case to absorb oil mist with a small pressure drop during blow-by gas through the filter. To do this, 3-D CFD analysis was simulated for the simplified PCV system with the oil filter using the commercial code, Ansys CFX. Results showed that the oil filter's efficiency with fleece sharply increased as oil droplet size increased.

• Tribology and Lubricants
• /
• 제21권2호
• /
• pp.83-92
• /
• 2005

A piston assembly is very important because it directly receives the energy generated during combustion process. Surely, the friction and lubrication of piston-ring pack do an important role in the performance and fuel economy of an engine. In fact, the friction loss in piston-ring pack is the biggest portion to the whole engine friction. Therefore, the improvement of lubrication quality and friction loss in piston-ring pack will be directly related with the improvement in the performance and fuel economy of an engine. Meanwhile, the oil consumption and blow-by gas through piston-cylinder-ring crevices have to be controlled as less as possible. In these two aspects, the study on the optimized design of piston-ring pack has to be carried out. In this study, for the efficient design of piston-ring pack, it is focused to develop a basic computer program that predicts the inter-ring pressure, the motion of ring and the blow-by gas through a crevice volume model between adjacent rings, and the oil film thickness and the friction computed by lubrication theories.

• 한국안전학회지
• /
• 제20권1호
• /
• pp.36-41
• /
• 2005

PCV(Positive Crankcase Ventilation) valve acts as a flow control valve to get a re-combustion of blow-by gas by having it flow from a crankcase to an inlet manifold suction tube. The blow-by gas of the crankcase should be eliminated or taken properly because it cause corrosion to critical parts, and contributes to increase crankcase pressure that can cause a drop in efficiency. The excessive stress and strain on the PCV valve that remove these harmful gas would be bring the difficult on the flow rate control and failure of the valve. Those condition inevitably induce the accident. Therefore, this study purpose is FEM evaluation of the stresses and deformation in the X3 PCV model according to the change of the differential pressure between inlet and outlet. From results, the maximum equivalent stresses increased linearly according to the increase of the differential pressure at the about 50mm from the inlet position and were under the yield strength of the valve. And the deformations were relatively small regardless of the in-outlet differential pressure variation.