• 대한토목학회논문집
• /
• 제34권1호
• /
• pp.175-183
• /
• 2014

본 연구는 점토지반에서 터널의 굴착조건(터널깊이 및 터널직경)과 시공조건(지반손실량), 지반조건(연약점토, 단단한 점토)을 변화시키면서 터널상부에 위치한 구조물의 거동변화를 조사 및 분석한 것이다. 분석에 사용된 구조물은 4층 블록식구조물로서 변형 등에 의한 균열발생과 균열폭의 차이로 인해 구조물의 손상정도를 쉽게 파악할 수 있는 특징이 있다. 다양한 터널 굴착조건 및 시공조건, 지반조건에 대해서 발생할 수 있는 터널상부 블록구조물의 거동상태를 파악하기 위해 수치해석적 매개변수 해석을 수행하였으며, 수치해석은 구조물의 실제크랙 발생을 묘사할 수 있도록 개별요소법(DEM)에 근거하여 수행하였다. 다양한 매개변수 해석으로부터 얻어진 구조물의 거동상태에 대한 결과는 터널 굴착조건 및 시공조건, 점토 지반조건과 상호 연관하여 함께 반영될 수 있도록 도표화 하였으며, 이를 이용하여 향후 점토지반에서 다양한 터널굴착 및 시공조건, 지반조건으로 인해 유발되는 터널 상부구조물의 손상정도를 보다 용이하게 파악할 수 있을 것으로 기대된다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1502-1508
• /
• 2011

Ground anchor expands the hollow wall of settled part and has the structure which resists the designed tensile load by the bearing pressure generated by the wedge of the anchor body pressing in the expanded part. Such ground anchor has been recognized for stability and economicality since 1960s in technologically advanced nations such as Japan and Europe, and in 1970s, the Japan Society of Soil Engineering has established and announced the anchor concept map. The ground anchor introduced in Korea, however, has the structural problem where the tensile strength is comes only from the ground frictional force due to expansion of the wedge body. In an interval where the ground strength is locally reduced due to fault, discontinuation or such, this is pointed out as a critical weakness where the anchor body of around 1.0m must resist the tensile load. Also, in the installation of concrete block, the concentrated stress of concrete block constructed on the uneven rock surface causes damage, and many such issues in the anchor head have been reported. Thus, in this study, by using the expanded bit for precise expansion of settled part, the ground anchor system was completed so that the bearing pressure of ground anchor can be expressed as much as possible, and the bearing plate was inserted into the ground to resolve the existing issues of concrete block. Through numerical analysis and pullout test executed for verification of site applicability, the pullout-behavior characteristics of anchor was analyzed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.820-825
• /
• 2007

A ballscrew-linear motion(LM) guide is well-described by its name: it is a LM guide that runs by ballscrew. It consists of LM rail, LM block, end plate, screw, nut and bearing balls. The ballscrew-LM guide has many advantages compared with conventional LM guide. The high efficiency achieved with rolling contact devices permits the employment of antibacklash methods. The balls provide the only physical contact between nut rail and block and ball screw and nut replacing the sliding friction with a rolling motion. The life of the ballscrew-LM is determinated by the balls. The objective of this paper is to introduce the design of the ballscrew-LM with the safety working load.

• 한국환경복원기술학회지
• /
• 제3권4호
• /
• pp.1-10
• /
• 2000

This study aims at the new design system development of landscape architecture structures, as soundproof wall using reinforced soil block. This structures, that is new soundproof wall system, have to be maintained stability on acting critical wind load, which is combined exist soundproof wall system and soundproof wall system using environmental green stone block. To the harmony of this system, the post block, so-called landscape block or cast block, is manufactured. It's possible to stand of the post bearing system combined with post-pile and post block. Through the comparison with a serious code for the acting wind load on the soundproof wall, the reasonable wind load could be calculated. Also, the mechanical stability on the green stone block was checked by the Lab. tests based on the UBC (Uniformed Building Code). Because the critical height of soundproof wall system using green stone generally was restricted, the new system demands to combination of the exist system and the new system. For the stability analysis of them, the utility program, SAP2000, was used. And, a semi-auto program on the design system of the new soundproof wall using green stone was developed, which can be easily use because of the simplification.

• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.440-447
• /
• 2020

조적구조는 소규모 건축물에서는 내력벽으로 사용되나 일반적으로 비내력벽으로 간주되어 건축물 골조구조의 내부공간을 구분하는 칸막이벽으로 활용되어진다. 또한 조적공사에서 블록이나 벽돌간의 접착제로 모르타르를 사용하는 습식공법은 양생시간이 필요하여 기후조건에 영향을 받으며, 특히 지진과 같은 횡력에 대해 모르타르의 균열로 벽체의 전도붕괴 등이 발생할 수 있어 매우 취약한 구조이다. 본 연구에서는 이러한 조적구조의 약축방향 전단강성을 보완하고 습식공법의 단점을 개선하는 건식 콘크리트블록 공법을 제안하고 그 구조거동을 규명하고자 한다. 이에 본 연구에서는 콘크리트블록의 재료물성을 살펴보고 수평반복하중에 대한 구조거동실험을 통해 제안된 건식조립 콘크리트블록 벽체의 내진성능을 검증하고자 한다. 본 연구결과에 의하면 첫째로, 콘크리트블록은 KS규준에 C종 블록의 재료성능 이상을 확보하고 있어 습식공법을 대신하는 건식공법에 적용할 수 있을 것이다. 둘째로, 수평반복하중에 대한 벽체의 구조성능은 벽체의 수평길이가 길어짐에 따라 사용된 표준형블록의 증가로 다수의 대각선방향 균열대를 형성하면서 조립블록벽체의 내력이 커짐을 알 수 있다. 끝으로 제안된 건식조립 콘크리트블록 벽체구조는 높이와 길이에 의한 벽체의 형상비가 수평 하중을 받는 구조거동에 주요 영향변수로 판단되어 이를 고려한 내진성능평가가 필요하다.

• 한국지반신소재학회논문집
• /
• 제5권1호
• /
• pp.9-14
• /
• 2006

국내에서는 여러 가지 형상 및 친환경적인 보강토옹벽 구조물의 시공은 최근 많이 확대되고 있다. 전체구조물의 안정과 더불어 블록에 발생되는 균열은 대부분 원인으로 기초의 침하에 의한 경우가 많다. 본 연구에서는 기초지반의 부등침하와 관련하여 기초지지력의 설계시 평가법 및 시공시 평가법에 대하여 고찰하였다. 현장에서 실시되고 있는 실제 시공사례를 이용하여 보강토옹벽의 안정을 기초지지력을 만족하지 못하는 경우에 대한 대책방안을 제시하고 그 방안의 활용성을 제시하였다. 보강토옹벽의 기초부분은 전체사면의 잠재적 활동면의 범주내에 있게 되므로 기초지지력을 담당하는 지반은 지반의 활동저항력에 영향을 받게 된다. 따라서, 기초지지력을 부담하는 기초지반은 지지력에 대한 안정을 만족할 뿐 만 아니라 전체사면활동에 저항하는 억지능력에 대하여도 고려되어야 한다.

• 한국농공학회지
• /
• 제30권1호
• /
• pp.38-49
• /
• 1988

This paper presented as follows results of laboratory model tests with various shaped footings on soil bed reinforced with the strips on the base of behaviour of soil structure according to the loads and triaxial test results reinforced with geotextiles. Their parameters studied were the effects on the bearing capacity of a footing of the first layer of reinforcement, horizontal and vertical spacing of layers, number of layers, tensile strength of reinforcement and iclination load to the vertical 1.Depending on the strip arrangement, ultimate bearing capacity values could be more improved than urreinforced soil and the failure of soil was that the soil structure was transfered from the macrospace to microspase and its arrangement, from edge to edge to face to face. 2.The reinforcement was produced the reinforcing effects due to controlling the value of factor of one and permeable reinforcement was never a barrier of drainage condition. 3.Strength ratio was decreased as a linear shape according to increment of saturation degree of soil used even though at the lower strength ratio, the value of M-factor was rot influenced on the strength ratio but impermeable reinforcement decreased the strength of bearing capacity. 4.Ultimate bearing capacity under the plane-strain condition was appeared a little larger than triaxial or the other theoretical formulars and the circular footing more effective. 5.The maximum reinforcing effects were obtained at U I B=o.5, B / B=3 and N=3, when over that limit only acting as a anchor, and same strength of fabric appeared larger reinforcing effects compared to the thinner one. 6.As the LDR increased, more and more BCR occurred and there was appeared a block action below Z / B=O.5, but over the value, decrement of BCR was shown linear relation, and no effects above one. 7.The coefficient of the inclination was shown of minimum at the three layers of fabrics, but the value of H / B related to the ultimate load was decreased as increment of inclination degree, even though over the value of 4.5 there wasn't expected to the reinforcing effects As a consequence of the effects on load inclination, the degree of inclination of 15 per cent was decreased the bearing capacity of 70 per cent but irnproved the effects of 45 per cent through the insertion of geotextile.

• 대한조선학회논문집
• /
• 제49권4호
• /
• pp.304-311
• /
• 2012

One of the main features of Drillship or FPSO is a moonpool structure. The moonpool structures have various accuracy tolerances according to their functions and targets. This study is mainly interested in roundness of a circular moonpool structure in FPSO. Because this structure needs abrasion-resistance at which bearing of machine touches on inner wall of moonpool, we should do over-lay welding widely and deeply by using Inconel weld material. But a general over-lay can cause a severe distortion at ship block structure. If we can analyze the roundness by thermal distortion under Inconel over-lay, we can establish a special erection policy by the results. In this study, we designed stress-strain curve for strain-boundary condition analysis by an elasto-plastic material property. The results made us to decide an appropriate ship-block size and policy of crane manipulation will follow for its capacity. If a structure that needs over-lay is not large, solid elements also are not a bad choice for FEM modeling. Therefore we also developed a standard of using strain-boundary method that shell elements are used as over-lay on solid element modeling.

• The Korean Journal of Ecology
• /
• 제14권1호
• /
• pp.25-38
• /
• 1991

Berchemia berchemiaefolia is a native a native rare plant which has been designating as the Natural Monument, No. 266, since 1980. The floristic composition, population structure and maintenance mechanism of the Berchemia berchemiaefolia forest were investigated in conjunction with the habitat consisted of the block field or screes. Through the present study, the authors found a new habitat of Berchemia berchemiaefolia in the northeastern slope on Mt. Kumdansan located at Hajeok-ri, Cheongcheon-myeon, Koesan-gun, chungbuk province. Gravels consisted of the block field belonged to granule, pebble and cobble as the range of grain size, $\Phi$=-1.5~6.6 values. The tree layer of Berchemia berchemiaefolia community was mainly composed of Quercus variabilis, Pinus densiflora and Q. serrata including Berchemia berchemiaefolia and of this community were similar to that of Q. variabilis. By the age distribution, it was considered that the community was a discontinued one as the pattern of distribution was a normal distribution type(N type). Phenological cycle including leafing, blooming and seed-bearing period between both sites of block field and valley or close canopy showed some differences. The seed production of Berchemia berchemiaefolia was 8, 655, 000 seeds/ha/year, but only 406, 000 seeds/ha/year of them were developed as saplings, and only 4 saplings were developed to mature trees.

• 한국구조물진단유지관리공학회 논문집
• /
• 제13권6호통권58호
• /
• pp.176-182
• /
• 2009

단조롭고 자연친화적이지 못한 기존 연안블록의 설계 및 시공으로 인하여, 연안침식방지 블록이 효과적으로 제 기능을 발휘하지 못하고 또 다른 피해가 발생되고 있다. 국민소득의 증대와 Waterfront 개념의 빠른 확산으로 연안 어항의 낙후된 시설개선 등에 많은 사업이 추진되고 있으나 이러한 용도에 맞는 자연 친화형 구조물이 개발된 바 없어 기존의 Solid Block, Igloo Block, Tunnel Block 등이 일부 현장에 적용되고 있는 실정이다. 선박이 계류하는 안벽이나 물양장 등에서 항내 진입파와 항파 등으로 인한 반사파의 발생에 의한 공진현상으로 항내파고가 높아져 정온도유지가 어렵고 선박의 계류 및 하역에 지장을 주게 되며, 선박과의 충돌 발생으로 인한 소형선박의 손괴 발생율이 높은 실정이므로 새로운 형태의 블록(Block)개발이 필요하다. 이에 따라 개발한 C.E.(Coastal Environments)블록을 현장에서 사용하기 위해서는 전단키 부분의 내하력 평가가 요구 된다. 따라서, 본 연구는 C.E. 블록의 연결부 시험편을 제작하여 C.E.블록 경계면의 마찰실험을 실시하였으며, 실험에서 얻은 C.E.블록 연결부의 마찰계수를 유한요소 해석에 사용하여 C.E.블록의 블록과 블록 접촉면의 마찰 계수를 산정하고자 한다.