• 대한족부족관절학회지
• /
• 제18권3호
• /
• pp.133-136
• /
• 2014

Skin grafting is often required for diabetic ulcerative foot lesions. In skin grafting, effective regional or local anesthesia into the donor and recipient areas plays a significant role in continuous control of pain. We report on a technique of ultrasound-guided nerve block on the femoral, sciatic, and lateral femoral cutaneous nerves in large split-thickness skin grafting for ulcer of the foot and leg.

• 자동차안전학회지
• /
• 제6권1호
• /
• pp.33-40
• /
• 2014

In this study the cylinder liner deformation which is one of the most influencing factors in a diesel engine oil consumption was performed by the finite element analysis on the basic designed structure consisting of the cylinder block, head and liners under the conditions of assembly, thermal and gas loads. Compared with a large number of other cylinder blocks showing remarkable harmonic orders of the liner distortion, results are excellent. Namely. the higher harmonic order amplitudes of the radial liner deformation amount to 1 ~ 2㎛ maximally. The main reason lies in the relatively large wall thickness of the liner which amounts to 8.2% of the bore diameter. Besides, a very stiff and symmetrical cylinder block design in combination with a bolt force introduction approximately 1.5mm below the block top deck have a further share on these results. Therefore excellent low oil consumption can be expected.

• 한국해양공학회지
• /
• 제31권6호
• /
• pp.425-430
• /
• 2017

In order to reduce the cost of corrections and time needed for the block assembly process, the reverse setting method is applied for a back-heated block to neutralize deck deformation. The proper reverse setting shape for a back-heated block to correct deformation improved the deck flatness, but an excessive amount of reverse setting could inversely affect the flatness of the block. A prediction method was developed for the proper reverse setting shape using a back-heated block, considering the complex geometry of blocks, thickness of the deck plate, and thermal loading conditions such as welding and back-heating. The prediction method was developed by combining the re-meshing technique and inherent strain-based deformation analysis using the finite element method. Because the flatness deviation was decreased until the lower critical point and thereafter it tended to increase again, the optimum value for which the flatness was the best case was selected by repeatedly calculating the predefined reverse setting values. Based on this analysis and the study of the back-heating deformation of large assembly blocks, including the reverse setting shape, the mechanism for selecting the optimum reverse setting value was identified. The developed method was applied to the actual blocks of a ship, and it was confirmed that the flatness of the block was improved. It is concluded that the developed prediction method can be used to predict the optimum reverse setting shape value of a ship's block, which will reduce the cost of corrections in the construction stage.

• 대한조선학회논문집
• /
• 제49권5호
• /
• pp.433-439
• /
• 2012

Anticorrosive paint is the most widely used in shipbuilding and the dry film thickness is very important in terms of productivity and assurance of anticorrosive performance. However, it is difficult to achieve the recommended target film thickness because the dry film thickness depends on labor's skill in practice and is affected by a number of parameters, such as spray pressure, paint flow rate, tip size, spray distance, SVR(Solid Volume Ratio), etc. Present paper derives an empirical equation through the correlation analysis of parameters selected by spray experiments of anti corrosive painting in order to predict the coated status. Comparing the calculated results with practical data, we show that the empirical equation can successfully expect DFT(Dry Film Thickness).

• Nuclear Engineering and Technology
• /
• 제56권8호
• /
• pp.3090-3096
• /
• 2024

In prompt fission neutron uranium logging, borehole environmental parameters affect the measured results and must be corrected. In order to explore the influence of borehole parameters on the interpretation of logging results, this paper builds a sandstone type uranium ore block model to simulate the field production drilling device based on the "Epithermal/Thermal neutron counting rate ratio" (E/T) theory. The effects of borehole diameter, thickness of iron tube and well fluid on the decay rate of epithermal and thermal neutrons and their uncertainty correction methods were investigated. The results show that the effect of borehole diameter on E/T is negligible. The iron tube thickness has a certain effect on the moderation and absorption of epithermal and thermal neutrons, and its E/T increases slightly with increasing thickness. The influence of iron tube thickness on E/T is corrected and the relative uncertainty is less than 5%. The well fluid thickness also affects the decay rate of epithermal and thermal neutrons, and its E/T follows the law of negative exponential attenuation. The influence of well fluid thickness on E/T is corrected and the relative uncertainty is less than 5%. This study provides technical guidance for field well survey of uranium deposit.

• 한국정밀공학회지
• /
• 제32권10호
• /
• pp.865-871
• /
• 2015

This study was conducted in order to develop a finger exoskeleton system using ionic polymer metal composites (IPMCs) as the actuator and sensor in a hybrid structure. To use the IPMC as an actuator producing large force, a first order transfer function was obtained using results from a block force for DC excitation that applied to two IPMCs of 20mm-width, 50mm-length, and 2.4mm thickness together. After which the validation of 200gf control with anti-windup PI controller was confirmed. A 5mm-width, 50mm-length, 0.6mm-thickness of IPMC was also modeled as a sensor for tip displacement. As a result, the IPMC sensor could been utilized as a trigger role for the actuator. Finally, an IPMC sensor and actuator were installed on the joint of a single DOF exoskeleton in the hybrid structure, and test for the control of 40gf of block force and predefined sequence of motion was performed.

• Macromolecular Research
• /
• 제10권2호
• /
• pp.67-74
• /
• 2002

New immunoprotecting membranes were prepared by spin coating the amphiphilic random multiblock copolymers of poly(ethylene glycol) (PEG) and poly(tetramethylene ether glycol) (PTMEG) or poly(dimethyl siloxane) (PDMS) on porous Durapore(R) membrane. The copolymer coating was intended to make a biocompatible, immunoprotecting diffusional barrier and the supporting porous substrate was for mechanical stability and processability. By filling Durapore(R) membrane pores with water, the penetration of coating solution into the pores was minimized during the spin coating process. A single coating process produced a completely covered thin surface layer (~1 ${\mu}{\textrm}{m}$ in thickness) on the porous substrate membrane. The permselectivity of the coated layer was influenced by PEG block length, polymer composition, and thickness of the coating layer. A composite membrane with the coating layer prepared with PEG 2 K/PTMEG 2 K block copolymer showed that its molecular weight cut-of fat any 40 based on dextran was close to the molecular size of IgG (Mw = 150 kDa). However, IgG permeation was detected from protein permeation test, while glucose oxidase (Mw = 186 kDa) was not permeable through the coated membrane.

• 치과방사선
• /
• 제27권1호
• /
• pp.87-97
• /
• 1997

The purpose of this study was to evaluate the method for quantitative assessment of bone mass from aluminum-equivalent value of hydroxyapatite by using digital imaging system consisted of Power Macintosh 7200/120, 15-inch color monitor, and GT-9000 scanner with transparency unit. After aluminum-equivalent image made from correlation between aluminum thickness and grey scale, the accuracy of conversion to mass from aluminum-equivalent value was evaluated. Measured bone mass was compared with converted bone mass from aluminum-equivalent value of hydroxyapatite block by correlation formula between aluminum-equivalent value of hydroxyapatite block and hydroxyapatite mass. The results of this study were as follow; 1. Correlation between aluminum thickness and grey level for obtaining aluminum-equivalent image was high positively associated(r²=0.99). Converted masses from aluminum-equivalent value were very similar to measured masses. There was, statistically, no significant difference(P<0.05) between them 2. Correlation between hydroxyapatite aluminum-equivalent and hydroxyapatite mass was shown to linear relation (r²=0.95). 3. Converted masses from aluminum-equivalent value of 3 dry mandible segments were similar to measured masses. The difference between the exposure directions was not significantly different(P<0.05).

• 전자공학회논문지CI
• /
• 제40권4호
• /
• pp.206-213
• /
• 2003

본 논문에서는 고성능의 하드웨어 장비가 아닌 일반적으로 사용되는 개인용 컴퓨터와 CCD 카메라를 이용하여 자동으로 경량기포 콘크리트(autoclaved lightweight concrete) 블록간의 상하 경사도, 두께의 불균일성, 그리고 불량 여부를 판별할 수 있는 알고리즘을 제안하였다. 제안한 치수측정 및 불량검사 자동화 알고리즘은 실제 작업환경을 고려하여 일반적인 조명조건에서의 전처리과정과 작업공정내의 피사체의 진동을 고려한 단위길이 결정방법, 카메라의 곡률보정에 의한 치수오차 보정 방법 등을 적용하였으며, 실제공정에서의 실험 결과를 통해 블록군의 계측에 있어서 0.8초 이내에 측정오차 1%이내의 데이터를 산출해 냄으로서 제안한 불량검사 자동화시스템의 신뢰성을 검증할 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.692-695
• /
• 2000

This paper is concerned with Accuracy Design of LM Guide System in Machine Tools. Elastic deformation of bearing is calculated by Hertz contact theory and motion error of LM block is analyzed. A new algorithm using block stiffness is proposed fur the analysis of motion accuracy of the table. The best advantage of this algorithm is fast analysis speed because it isn't necessary iteration processes for satisfying equilibrium equation of the table. Motion errors of the table analyzed under artificial form error of rail theoretically and experimentally. Only one of two rails is bent by putting a thickness gauge into horizontal direction. This form error of rail is measured by gap sensor against the other rail. Then, motion errors of the table are predicted by proposed new algorithm theoretically and measured by laser interferometer. Measurements are carried out by changing the preload and thickness. The results show that the table motion errors are reduced from 1/2 to 1/60 times than form error of rail according to its height and width. And the effect of preloading is almost negligible.