• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.1
• /
• pp.1-11
• /
• 2022

In a gas turbine, fuel is exposed to a high temperature environment until it is fed to the combustor through the injector. Hydrocarbon fuels can coke under high temperature conditions, which can cause coking material to deposit on fuel lines or block the injector passages. In this study, a specimen simulating a fuel line located inside a gas turbine and Jet A-1 were heated using electric devices. Jet A-1 coking tests were performed by changing the wall temperature of the stainless steel specimen and the temperature of Jet A-1 supplied to the specimen. After the coked specimens were cut, the coking material and the inner surface were analyzed using an energy dispersive X-ray spectrometer and a field emission scanning electron microscope.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.69-75
• /
• 2008

Shear tests were carried out on interface between two concrete eco-blocks which comprise segmental retaining wall. Three interface conditions were considered : 1) direct contact of two blocks, 2) placing rubber pad between two blocks, 3) placing rubber pad and shear key between two blocks. According to shear tests, shear load-shear displacement relationship which was obtained from direct contact of two blocks was similar to elastic-perfectly plastic behavior. Ductile behavior of shear load-shear displacement relationship was observed for the interface condition of placing rubber pad. Apparent minimum shear capacities and apparent friction angles for the interface conditions of direct contact of two blocks, placing rubber pad between two blocks, placing rubber pad and shear key were 1.7 kN/m, $27.6^{\circ}$ and 4.2 kN/m, $26.2^{\circ}$ and 20.9 kN/m, $26.0^{\circ}$ respectively.

• Journal of The Geomorphological Association of Korea
• /
• v.26 no.1
• /
• pp.41-57
• /
• 2019

The grain size characteristics of river sediments and the characteristics of bedrock were investigated for the 24km section of the Dong River upstream of the Han River. The bedrock of the study area is various limestone belonging to the Paleozoic Choseon limestone group, and Mesozoic sandstone and conglomerate occur in some areas. Most of the river channel is made of limestone, and most of the river bottom is covered with fluvial sediments. More than 70% of these sediments are sandstone and conglomerate, rather than limestone which forms the basis of the valley. Sediment particles seem to have been supplied upstream of the study area rather supplied from the slope near of the channel. It is difficult to find the statistically significant difference in the shape of the sediment particles of limestones and non-limestones. However, limestones has platy forms rather than block forms, it can be assumed that the limestone was supplied from the surrounding valley wall and transported over a short distance. The particle sizes of DG1~DG2(the upstream section) are decreasing in the downstream direction. However, at DG3, which is a tributary, Jijangcheon, confluence particle size increases and at DG4 particle size increases more. In the case of DG4, it may be influenced by the influx of tributaries, but it also can be supposed as the impact of the large flood in 2002. In the downstream parts(DG5~DG7), the particle size decreases exponentially with distance. The rebound strength of stream sediments and bedrock was measured by using Schmidt hammer. Limestone showed lower rebound strength than non-limestone. According to the results of the sediment and bedrock, it can be seen that the sandstone and conglomerate with high rebound values pass through valley with the relatively low strength limestone. The sediments of limestone were decreased in grain size more rapidly than those of limestone sediments.

• Korean Journal of Poultry Science
• /
• v.35 no.2
• /
• pp.183-190
• /
• 2008

This study was conducted to investigate the effect of feeding diets supplemented with ${\beta}-glucan$ products on the performance, small intestinal microflora and immune response in laying hens. The ${\beta}-glucan$ products used in the experiment were $BetaPolo^{(R)}$ ; soluble ${\beta}-glucan$ of microbial cell wall origin, $HiGlu^{(R)}$ ; microbial cell wall origin, $OGlu^{(R)}$ ; oat origin, $BGlu^{(R)}$ ; barley origin. A total of 720 Hy-Line Brown laying hens of 40wks old were divided into 5 dietary treatments : T1 ; Control( C), T2 ; $BetaPolo^{(R)}$, T3 ; $HiGlu^{(R)}$, T4 ; $OGlu^{(R)}$, T5 ; $BGlu^{(R)}$. Each treatment was replicated 4 times with 36 birds/replicate housed in 2 bird cages, and arranged according to completely randomized block design. Feeding trial lasted 40ds under 16 h lighting regimens. There were significant differences among treatments in hen-house egg production feed intake and feed conversion. HiGlu treatment was significantly higher than OGlu treatments in hen-house egg production. ${\beta}-glucan$ supplemented treatments were lower than the control in feed intake and feed conversion ratio. All ${\beta}-glucan$ supplemented treatments were significantly higher than the control in eggshell strength. Eggshell color and Haugh unit tended to be lower in the supplemented group than the control. IgY concentration was not significantly affected by treatments. At $5^{th}$ week of experiment, however, IgY concentration tended to increase in the supplemented groups. Among the leucocytes parameters, WBC, heterophil, lymphocytes, monocyte and eosinophil concentration were lower in the supplemented groups than those of the control. Among erythrocytes, HCT(hematocrit) and MCV(mean corpuscular volume) were significantly affected by treatment. MCV of supplemented groups were higher than that of the control. Immunoglobulin concentrations in the birds were not significantly different among treatments. However, IgA concentration tended to be low in the supplemented groups than the control. The cfu of small intestinal microflora were not significantly different among treatments, but that of Cl. perfringens tended to be lower than the control. The result of this experiment indicateted that feeding ${\beta}-glucan$ to laying hens improve feed conversion ratio and eggshell strength. Also intestinal microflora and immune responses are modified.

• Journal of Animal Environmental Science
• /
• v.11 no.3
• /
• pp.169-176
• /
• 2005

The farm house structure, ventilation system and manure treatment of two-storey buildings and sawdust pig houses were surveyed and analyzed. Based on the data for ten selected farms in five provinces during eight months, the goal is to eventually establish a standard two-storey pig house. Manure treatments were composting, slurry and activated sludge in two-storey pig houses, while fermentation method was done in sawdust pig house. The depth of sawdust as a litter material were 10 to 60cm, with a duration of 1/2, 1, 3 and 6 months, respectively. The ventilation systems were the mechanical type in two-storey pig houses and natural system in the sawdust pig house. Side wall in the two-storey pig house was enclosed with insulation materials such as block, colored metal sheet and sandwich panels. The minimum ceiling height in the first floor of the two-storey pig house was 2.0m and the maximum was 3.0m. On the second floor, ceiling height ranged from 2.0 to 2.7m. The construction cost in the two-storey systems were $700\~140$, and sidewall curtain systems were $30\~40$ thousand Won/pyung.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.7
• /
• pp.418-425
• /
• 2017

ZnO nanoparticles (ZnO NPs) are mainly used in semiconductors, solar cells, biosensors, and cosmetics (sunscreen). In this study, we investigated the behavior of ZnO NPs in aquatic and soil environments and their effects on plants (Artemisia annua L.) in hydroponic cultivation. It was confirmed that the ZnO NPs size increased and their dissolution decreased with increasing in pH. Leaching distance of ZnO NPs was less than 2.5 cm, indicating that ZnO NPs had a little potential to leach into deeper soil layers. When ZnO NPs were exposed to plant, the total weights of plants decreased. The effects on the length of root and shoot were not observed. In addition large amount of ZnO NPs were adsorbed on the surface of plant root and didn't translocate into shoot. These results suggest that ZnO NPs block the pores of the root cell wall and decrease the bioavailability of plant nutrients. Therefore it can be speculated that the particles increase in size and settle down in the water environment and may adversely affect the plant growth by firmly adhering to the root surface when the ZnO NPs are exposed to the environment.

• Journal of the Korean Wood Science and Technology
• /
• v.3 no.1
• /
• pp.3-15
• /
• 1975

How to stabilize wood against shrinking and swelling in variable atmospheric moisture conditions is important to the wood-using industry and a challenge to research. Polyethylene glycol stabilize wood by bulking the fiber. PEG also serve as a chemical seasoning agent, suppress decay in high concentrations, and have slight effect on physical properties, gluing or finishing. The study designed to determine the effect of PEG-400 on the dimensional stabilization of local hardwoods for wood carvings that could supply a greatly expanding tourist trade and making curved furniture parts, lamp stands and other decorative objects, and possible gunstock. The species examined were 6 species, Seo-Namoo (Carpinus laxiflora), Cheungcheung-Namoo (Cornus controversa), Gorosae-Namoo (Acer mono), Karae-Namoo (Juglans mandshurica), Jolcham-Namoo (Quercusserrata) and Sanbud-Namoo (Prunus sargentii), used as block of 5cm thick radially to the grain, 7cm wide tangentially, and 70cm long parallel to the wood grain. All these test piecies were conditioned above the fiber saturation point before impregnation. The stabilization effects were determined for PEG-400 treated woods in a 50 percent solution for 20 days. The following conclusions were obtained. PEG retentions increased with treating time. It was more effective to treat at 60$^{\circ}C$ than at room temperature. In degree of PEG-400 impregnation on species, Cheungcheung-Namoo havinglow specific gravity had the highest retentions, 68.77% but the lowest, 56.33% was shown in Jolcham-Namoo with high specific gravity. Specific gravity of treated wood increased considerably with effectiveness of polymer loading. The increases in specific gravity were 5.36 to 13.16 percent. The highest was Jolcham-Namoo, the lowest Karae-Namoo. On the dimensional stability, a 40 percent of effectiveness of polymer loading was just as effective as 60 percent in reduction in water absorptivity (RWA), antishrinkage efficiency (ASE) and antiswelling efficiency (AE), and from over 60 percent they increased more rapidly. Also species response varied considerably. ASE was 30.12 to 69.97 percent tangentially and 27.86 to 56.37 percent radially, AE 34.06 to 73.76 percent tangentially and 30.11 to 70.12 percent radially, and RWA 42.31 to 65.32 percent. No differences in volume swelling among the 6 species were observed. Its values were ranged from 14.98 to 19.55 percent and also increased with PEG retentions. On the mechanical properties, the strengths very much decreased with PEG-400 loadings as shown in Figure 12; that were 11.41 to 22.90 percent in compression, 21.61 to 34.35 percent in bending and 22.83 to 36.83 percent in tensile strength. PEG retention in cell wall was less than 1 percent and the most of PEG were immersed in cell lumen. Except for Korae-Namoo, effectivenesses of polymer loading were as much high as 61.58 to 75.02 percent. This is believed to be due to the effect of PEG-400 on excellant dimensional stability of treated woods.

• Journal of Periodontal and Implant Science
• /
• v.26 no.1
• /
• pp.47-67
• /
• 1996

The purpose of this study was to observe the effect of $Biocoral^R$ graft and bioglass 45S5 graft in combination with ePTFE membrane in periodontal osseous defects for new bone formation. Nine healthy dogs were used. Under general anesthesia, 3-wall defects were created on the mesial and distal surfaces of the maxillary right canines, the mesials of the maxillary right second premolars, the distals of the mandibular right canines and the mesials of the mandibular right third premolars. To induce periodontitis, a silicone rubber, $Provil^R$ light body, was injected under pressure into the defects. Ninety days later, $Provil^R$was removed and followed by thorough root planing. The followings were then applied in the mesial and distal defects of the maxillary right canines, the mesials of the maxillary right second premolars, the distals of the mandibular right canines and the mesials of the mandibular right third premolars by random selections : 1) ePTFE membrane only application, 2) $Biocoral^R$ graft, 3) $Biocoral^R$ graft and ePTFE membrane application, 4)Bioglass 45S5 graft, 5) Bioglass 45S5 graft and ePTFE membrane application. The membranes were removed 1 month later. The dogs were sacrified at 1, 2 and 3 months following the graft, and block sections were made, demineralized, embedded, stained and examined by light microscope and transmission electron microscope. On the sections from teeth treated with ePTFE membrane only, the defect demonstrated extensive connnective tissue and alveolar bone regeneration. The $Biocoral^R$ graft group demonstrated extensive bone regeneration compared with ePTFE membrane only group. In the $Biocoral^R$ graft plus ePTFE membrane group, regeneration of new alveolus and crest occurred within the defect. As the experimental period lengthened, bone regeneration was increased and bone bridge was formed among the graft particles. The but bioglass 45S5 graft group demonstrated extensive bone regeneration but the amount of new bone was less than that of the $Biocoral^R$ graft group. For the bioglass 45S5 graft plus ePTFE membrane group, the amount of new bone was also increased. As the experimental period lengthened, bone regeneration was increased. Multinucleated giant cells, fibroblasts and macrophages were observed. As the bone formation was increased, the number of such cells was decreased. In conclusion, the $Biocoral^R$ was found better than the bioglass 45S5 for new bone formation, and the use of ePTFE membrane alone or with $Biocoral^R$/bioglass 45S5 can be supported as potential methods of promoting bone formation.

• Ecology and Resilient Infrastructure
• /
• v.3 no.2
• /
• pp.143-151
• /
• 2016

Shoreline armoring is a globally used engineering strategy to prevent shoreline erosion along stream, lake and reservoir coastlines. Armoring alters the land-water interface and has the potential to affect shoreline vegetation by changing nearshore geomorphology, hydrology, sediment composition and water quality. We quantified the effects of the artificial disturbances and alternation of the land-water interface on the community structure and distribution of shoreline vegetation in a large reservoir, Uiam Reservoir, Korea. More than 60% of shorelines were disturbed by armoring with retaining wall of concrete block, riprap and gabion in the Uiam Reservoir. The results of detrended correspondence analysis showed that the vegetation structures of the shoreline modified by armoring changed from hydrophyte-dominated to hygrophyte-dominated ecosystems. The shoreline armoring caused the disruption of gradual continuity in the water-land interface and the biological invasion by alien plants. The changes in distribution area of shoreline vegetation showed that the area of hydrophytic vegetation decreased and that of hygrophytic vegetation increased from 2010 to 2013. In conclusion, the human disturbance such as armoring, road construction, recreation etc. could lead to terrestrialization, the loss of transverse continuity and biological invasion in the shoreline vegetation of the Reservoir Uiam. Our findings suggest that redesigning or removing shoreline armoring structures may benefit nearshore hydrophytic vegetation for the conservation of novel shoreline ecosystems.

• Journal of Chest Surgery
• /
• v.12 no.3
• /
• pp.281-288
• /
• 1979

For years, physicians and anatomists have been interested in the heart that has one functioning ventricle. Various terms have been suggested for this entity including single ventricle, common ventricle, double-inlet left ventricle, cor biatriatum triloculare, and primitive ventricle. In this report, the term "single ventricle" is utilized as suggested by Van Praagh, and is defined as that congenital cardiac anomaly in which a common or separate atrioventricular valves open into a ventricular chamber from which both great arterial trunks emerge. An outlet chamber, or infundibulum, may or may not be present and give rise to the origin of either of the great arteries. This definition excludes the entity of mitral and tricuspid atresia. An 11 year old cyanotic boy was admitted chief complaints of exertional dyspnea and frequent upper respiratory infection since 2 weeks after birth. He was diagnosed as inoperable cyanotic congenital heart disease, and remained without any corrective treatment up to his age of 11 year when he suffered from aggravation of symptoms and signs of congestive heart failure for 2 months before this admission. On 22nd of May 1979, he was admitted for total corrective operation under the impression of tricuspid atresia suggested by a pediatrician. Physical check revealed deep cyanosis with finger and toe clubbing, and grade V systolic ejection murmur with single second heart sound was audible at the left 3rd intercostal space. Development was moderate in height [135 cm] and weight[28Kg]. Routine lab findings were normal except increased hemoglobin [21.1gm%], hematocrit [64 %], and left axis deviation with left ventricular hypertrophy on EKG. Cardiac catheterization and angiography revealed 1-transposition of aorta, pulmonic valvular stenosis, double inlet of a single ventricle with d-loop, and normal atriovisceral relationship [Type III C solitus according to the classification of Van Praagh]. At operation, longitudinal incision at the outflow tract of right ventricle in between the right coronary artery and its branch [LAD from RCA] revealed high far anterior aortic valve which had fibrous continuity with mitral annulus, and pulmonic valve was stenotic up to 4 mm in diameter positioned posterolaterally to the aorta. Ventricular septum was totally defective, and one markedly hypertrophied moderator band originated from crista supraventricularis was connected down to the imaginary septum of the ventricular cavity as a pseudoseptum of the ventricle. Size of the defect was 3X3 cm2 in total. Patch closure of the defect with a Teflon felt of 3.5 x 4 cm2 was done with interrupted multiple sutures after cut off of the moderator band, which was resutured to the artificial septum after reconstruction of the ventricular septum. Pulmonic valvotomy was done from 4 mm to 11 mm in diameter thru another pulmonary arteriotomy incision, and right ventriculotomy wound was closed reconstructing the right ventricular outflow tract with pericardial autograft of 3 x 4 cm2. Atrial septal defect of 2 cm in diameter was closed with 3-0 Erdeck suture, and atrial wall was sutured also when rectal temperature reached from 24`C to 35.5`C. Complete A-V block was managed with temporary external pacemaker with a pacing rate of 110/min. thru myocardial wire, and arterial blood pressure of 80/50 mmHg was maintained with Isuprel or Dopamine dripping under the CVP of 25-cm saline. Consciousness was recovered one hour after the operation when his blood pressure reached 100 /70 mmHg, but vital signs were not stable, and bleeding from the pericardial drainage and complete anuria were persisted until his heart could not capture the pacemaker impulse, and patient died of low output syndrome 320 min after the operation.