• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.4
• /
• pp.534-540
• /
• 2003

This study was conducted to investigate the effect of supplementation of galacto-oligosaccharides (GOS) on methane emission, nutrient digestibility, energy utilization and blood metabolites by Holstein cows fed silages. In two sequential digestion and respiratory trials, two non-lactating Holstein cows were arranged to a balanced incomplete block design. Experimental diets consisted of two silage types; orchardgrass (Dactylis glomerata L.) based silage (OS), mixed silage (orchardgrass based silage and alfalfa (Medicago sativa L.) silage) (MS), while two GOS levels were without supplementation (0) and 2% of dry matter intake supplementation (2). Four combination diets were OS-0, OS-2, MS-0 and MS-2. Significant effects of silage types and GOS supplementation levels were not observed for DM and OM intake. Whereas the digestibility of OM, NDF and ADF was significantly (p<0.05) higher in cows fed OS with and without GOS compared cows fed MS diets. As percentage of GE intake, fecal energy loss for OS diets was significantly (p<0.05) declined than for MS diets. In contrast, cows fed MS diets had lower (p<0.05) urine energy loss as a proportion of GE intake compared to OS diets. Energy loss as CH4 and heat production was numerically increased when cows fed both OS and MS with GOS supplementation. Compared to OS, CH4 emission in cows fed MS was numerically decreased by 10.8 %. Methane conversion ratio (energy loss as CH4 per unit of GE intake) for OS-0, OS-2, MS-0 and MS-2 were 7.1, 7.2, 6.8 and 7.0, respectively. Plasma of glucose and urea-N concentration were significantly (p<0.05) elevated from 1 h to 6 h after feeding, otherwise total protein in plasma was declined (p<0.01) at 6 after feeding.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.5
• /
• pp.1485-1490
• /
• 2014

We have designed and developed a new ladder type tetrafused ${\pi}$-conjugated building block such as dihydroindolo[3,2-b]indole (DINI) and investigated its role as an electron rich unit. The photovoltaic properties of a new semiconducting ${\pi}$-conjugated polymer, poly[[5,10-bisoctyl-5,10-dihydroindolo[3,2-b]indole-[5,6- bis(octyloxy)-4,7-di(thiophen-2-yl)benzo[c][1,2,5]thiadiazole]], represented by PDINI-OBTC8 are described. The new polymer PDINI-OBTC8 was synthesized in donor-acceptor (D-A) fashion, where fused ${\pi}$-conjugated tetracyclic DINI, and 5,6-bis(octyloxy)-4,7-di(thiophen-2-yl) benzo[c][1,2,5]thiadiazole (OBTC8) were employed as electron rich (donor) and electron deficient (acceptor) moieties, respectively. The conventional bulk heterojunction (BHJ) device structure ITO/PEDOT:PSS/PDINI-OBTC8:PCB71M/LiF/Al was utilized to fabricate polymer solar cells (PSCs), which comprises the blend of PDINI-OBTC8 and [6,6]-phenyl-$C_{71}$-butyric acid methyl ester ($PC_{71}BM$) in BHJ network. A BHJ PSC that contain PDINI-OBTC8 delivered power conversion efficiency (PCE) value of 1.68% with 1 vol% of 1,8-diidooctane (DIO) under the illumination of A.M 1.5G 100 $mW/cm^2$.

• Journal of Korean Society on Water Environment
• /
• v.16 no.4
• /
• pp.469-477
• /
• 2000

Bisphenol-A (BPA), a known endocrine disruptor, is a main building block of epoxy resin which is widely used as a coating agent in residential water storage tanks. Therefore, BPA leaching from the epoxy resin may have adverse effects on human health. The possibility of BPA leaching from three epoxy resins were tested with a modified KS D 8502 method at 20, 50, 75 and $100^{\circ}C$ in deionized water and the specified test water, respectively. BPA leached to the test water was identified using GC-MS and quantified with GC-FID after a sequential extraction and concentration. The results showed that BPA leaching has occurred in all three samples tested. The quantify of BPA leaching from unit area of epoxy resin coating was in the range of $10.677{\sim}273.120{\mu}g/m^2$ for sample A, 29.737~1734.045 for sample B and 52.857~548.778 for sample C depending on the test temperature, respectively. In general, the amount of BPA leaching increased as the water temperature increases. This result implies a higher risk of BPA leaching to drinking water during a hot summer season. In addition, microbial growth, measured by colony forming units, in epoxy coated water tanks was higher than that in a stainless steel tank suggesting that compounds leaching from epoxy resin may support the growth of microorganisms in a residential water holding tank.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.3
• /
• pp.338-351
• /
• 2005

Statement of problem. Accurate fit between the implant components is important because the misfit of the implant components results in frequent screw loosening, irreversible screw fracture, plaque accumulation, poor soft tissue reaction, and destruction of osseointegration. Purpose. This study is to evaluate the machining accuracy and consistency of the implant fixture/ abutment/screw interfaces of the internal connection system by using a Stereoscopic Zoom microscope and FE-SEM(field emission scanning electron microscope) Materials and methods. The implant systems selected in this study were internal connection type implants from AVANA(Osstem^{\circledR}), Bioplant(Cowell-Medi^{\circledR}), Dio(DIO^{\circledR}), Neoplant(Neobiotech 􀋓), Implantium(Dentium􀋓)systems. Each group was acquired 2 fixtures at random. Two piece type abutment and one piece type abutment for use with each implant system were acquired. Screw were respectively used to hold a two piece type abutment to a implant fixture. The implant fixtures were perpendiculary mounted in acrylic resin block. Each two piece abutment was secured to the implant fixture by screw and one piece abutment also secured to the implant fixture. Abutment/fixture assembly were mounted in liquid unsaturated polyester. All samples were cross-sectioned with grinder-polisher unit. Finally all specimens were analysed the fit between implant fixture/abutment/screw interfaces Results and conclusions. 1. Implant fixture/abutment/screw connection interfaces of internal connection systems made in Korea were in good condition. 2. The results of the above study showed that materials and mechanical properties and quality of milling differed depending on their manufacturing companies.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.6
• /
• pp.11-17
• /
• 2001

Design and implementation of the MAC protocol processor prototype for high speed wireless LAN, which has interface with 5GHz OFDM PHY layer, is presented. We analyze the IEEE 802.11 MAC protocol specification and then separate the MAC protocol functions to be implemented by hardware and firmware and define the interface in which frames can be exchanged. That is, it is considered that high speed queue processing and interfaces with RISC processor and OFDM PHY layer. Protocol control and transmission/reception functions of the MAC functions are implemented in hardware in order to guarantee high speed processing in MAC layer. The developed MAC hardware block operates at 10MHz main clock. Therefore, transmission rate in PHY layer is about 80Mbps because data transmission/reception between MAC layer and PHY layer is performed as unit of octet. The designed FPGA MAC function chip has been implemented in wireless LAN test board and it is verified that DCF function is operated correctly.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.3
• /
• pp.358-374
• /
• 1999

This study measured the relative displacements of the five-unit fixed partial dentures as cast with the same fixed partial dentures sectioned and assembled by investment-soldering, solder-ing stand-soldering, and cast-joining techniques A total of fifteen specimens using a type IV gold alloy were one-piece cast as control and then sectioned and assembled five test specimens for each method were prepared. A computerized three dimensional coordinate measuring machine and specially designed cylinder for this study were used. Displacement was defined by six displacement variables for the each of cylinders incorporated in each casting: three component displacements(${\Delta}Lx,\;{\Delta}Ly,\;and\;{\Delta}Lz$) and rotational displacements(${\Delta}{\theta}x,\;{\Delta}{\theta}y,\;{\Delta}{\theta}z$). The global displacement was computed using the mathematical formula ${\Delta}R$ = Global displacement =$\sqrt{{(x'-x)}^2+{(y'-y)}^2+{(z'-z)}^2}$ Under the conditions of this study, the following conclusions were drawn: 1. The investment-soldering group showed the largest mean value of final global displacements, followed by stand-soldering group, cast-joining group and one-piece cast group. However, between the mean values of final global displacement for the cast-joining group and one-piece cast group, there was no significant difference. 2. For investment-soldering and stand-soldering groups, the greater global displacements were recorded in soldering phase than in indexing or investing phase. 3. For one-piece cast group, the displacements occured mostly in the casting phase. And for cast-joining group, there was no significant difference in global displacements among the fabricating procedures. 4. Intercentroidal distance decreased in framework-patterning, solder-indexing, solder-standing, and soldering phases, but increased in investment block-investing and casting phases. 5 Specially designed cylinder for touch-trigger type coordinate measuring machine was validated.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.3
• /
• pp.25-30
• /
• 2017

This paper introduces a novel method to quantify the morphological evolution of the strain response envelope. The strain response envelope is defined as an image in strain increment space corresponding to the unit stress input in stress space. Based on the shape of strain response envelopes, the deformation characteristics of soils can be described using the framework of elastic-plastic theory. Fourier descriptor analysis was used to investigate the morphological characteristics of strain response envelopes. The numerical results show that when the stress input remains in the initial yield surface the Fourier descriptors remain constant. Once the stress input crosses the initial yield surface, every descriptors deals in this study change. Numerical and experimental results of this study show that clear yielding response is only found in natural block samples. Among the Fourier descriptors, the descriptor called as asymmetry is the best for detecting the yield and is minimally sensitive to the number of input stress paths.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.14-22
• /
• 2010

Hybrid Electronic Vehicle (HEV) is one of the solutions of high oil price and environment problem. Recently, study of HEV is important for automobile industry. However HEV has a lot of components and there are many cases for assembling, it's impossible to test results from assembling by using real vehicles. To solve this problem, hybrid system simulator is required. The purpose of this study is to develop and optimize of engine module for hybrid system simulator. The commercial 1-D engine simulation program, WAVE is used to get the engine capacity and performance data and 1-D simulation model of base engine is compared with engine experiment results. Using the data, the engine module is developed based on the MATLAB Simulink. There are blocks of base engine, Single-CVVT engine and Dual-CVVT engine. The effect of acceleration and deceleration is applied to each engine block. In addition, the control and processing logics for CIS technology are developed. Finally the simulator operates FTP-72 mode test.

• Tunnel and Underground Space
• /
• v.10 no.1
• /
• pp.80-91
• /
• 2000

Open cut mining of limestone is generally considered to be more advantageous than underground mining in recovery, grade control, economics, and safety, but it causes substantial environmental pollutants such as ground vibration, noise, dust. It also changes ground surface and may destroy vegetation. The Halla limestone mine which lies adjacent to Baikdu mountains range is selected for a model study. To reduce environmental hazards, and to conserve original surface and woods, both open cut and underground mining methods must be adopted. In case of sub-level sloping. a unit block of 87m high, 70m wide, and 100∼l20m long is suggested with an estimated overall recovery of 42%. Some suggestions to reduce the environmental hazards are also included. The followings must be considered in determining the degree of fragmentation; the discontinuity conditions in the rock mass and the charge concentration both at the bottom and column of the hole. In addition to adopting a barrier wall for reducing environmental hazards, the probable production from underground mining is also discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.54-63
• /
• 2001

Rapid Prototyping(RP) techniques have their unique characteristics according to the working principles: stair-stepped surface of a part due to layer-by-layer stacking, low build speed caused by point-by-point or line-by-line solidification to build one layer, and additional posts processing to improve surface roughness, so high cost is required to introduce and to maintain the RP apparatus. The objective of this study is to develop a new RP process, Variable Lamination Manufacturing by using expandable polystyrene foam sheet as part material(VLM-S), and to design an apparatus for implementation of the process. So, the process parameters and design criterions of the apparatus were defined and the techniques were proposed to satisfy the design criterion. Based on the results, a knob-shape, pyramid shape. and a solid block were fabricated on the apparatus in which unit shape part(USP) was generated for building each layer.