• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.217-218
• /
• 2012

• 한국산업융합학회 논문집
• /
• 제22권6호
• /
• pp.711-719
• /
• 2019

At present, wind power is the fastest growing technology in the world. The domestic market depends heavily on imports for wind tower lift. so it manage through the overseas maker. The lift manufacture, establishment and maintenance utility is increasing, localization development of one wind tower lift is necessary with domestic fundamental base technique. In this paper, we will study the components necessary for the development of onshore offshore wind tower elevators, which are currently dependent on total imports, in line with the high growth of the wind market and the enlargement of the wind power generators. First of all, endless winders and cabins, which are the core components of the offshore wind tower lift, were examined for the components that affect the structural safety. Structural analysis was performed on Sheave, which is responsible for most of the lift lifting loads, and Block Stop, a safety device that prevents the cabin from falling in an emergency. The structural suitability was evaluated by comparing with the safety factor. In addition, the on-board control panel combines the control panel of the elevator and the drive motor driving the endless winder for efficient control of the offshore wind tower lift. The addition of features improves ride comfort at departure.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.422-429
• /
• 1997

Thermal stress induced by hydration heat may produce cracks in mass concrete structure, which can result in structural problems as well as bad appearance. To minimize crack occurrence in massive structural, thus, the study put an emphasis on the determination of optimized lift height and block size. In the parametric study different sizes and lift heights were used to measure the magnitudes of hydration heat and thermal stresses for 3 different types of concrete fabricated with 1 pure cement and 2 blended Portland cements. As a result of analysis. it was found that magnitude of hydration heat and the occurrence of thermal cracks depend on the restriction conditions and material characteristics, especially adiabatic material parameters. It was also found that optimized lift height and block size can be determined from an appropriate combination of the degree of inner and outer structural restrictions.

• Archives of Plastic Surgery
• /
• 제38권1호
• /
• pp.81-84
• /
• 2011

Purpose: Nerve injury is one of the complication which can develop after brow lift. Peripheral nerve ending which is stretched from supraorbital nerve and supratrochlear nerve can be injured and symptoms such as pain, dysesthesia may appear. Usually, developed pain disappeared spontaneously and does not go on chronic way. We experienced a case that a patient complained chronic pain after brow lift which was not controlled by conservative management such as medications, local nerve block and report a successful surgical treatment of chronic pain after brow lift. Methods: A 24-year-old male who received brow lift with hairline incision at local hospital was admitted for chronic pain at the right forehead. The pain was continued for 3 months even though fixed thread was removed. Local nerve block at trigger point with mixed 1 mL 2% lidocaine and 1 mL Triamcinolone acetonide was done and oral medications, Gabapentine and carbamazepine, were also applied but there was no difference in the degree of pain. Therefore the operation was performed so that careful dissection was carried out at right supraorbital neurovascular bundle and adhered supraorbital nerve was released from surrounding tissues and covered with silastic sheet to prevent adhesion. Results: The pain was gradually relieved for a week. The patient was discharged without complications. No evidence of recurrence has been observed for 2 years. Conclusion: The pain developed after brow lift was engaged with nerve injury and sometimes remains chronically. Many kinds of conservative management to treat this complication such as medications, local nerve block have been reported and usually been used. But there are some chronic cases that conservative treatment do not work. In sum, we report 1 case of successful surgical treatment for relief of intractable pain developed after brow lift surgery.

• 한국전산유체공학회지
• /
• 제17권3호
• /
• pp.18-24
• /
• 2012

The aerodynamic performance of the pantograph on a high speed train was compared for different pantograph covers which are designed to block the aero-acoustic noise from the pantograph. For the study, two types of cover are designed: wedge and cone types. The lift force of pantograph with cover was compared with the force of pantograph only. The comparison clarified that the cone type cover increases the sideslip angle of the flow and decreases the lift force considerably. However, the wedge type cover changes the flow direction upward and increases the lift force of the pan head. This increment of lift force compensates the decrement of lift force caused by the blocking of the flow into the pantograph lower frame due to cover. Therefore, in case of the wedge type cover, the overall lift force changes slightly compared with the cone type cover.

• 대한토목학회논문집
• /
• 제29권1B호
• /
• pp.83-90
• /
• 2009

본 연구는 잔교를 설계할 때 수리모형실험을 통하여 잔교상판에 작용하는 양압력 분포 특성에 대해 기술하였다. 양압력이 상판하부에 작용할 때 압축공기 유출의 유무에 따라 양압력이 작용하는 형상이 다르고 양압력의 크기가 다르게 분포하고 있음을 알았다. 동일 Block 상판내의 양압력분포는 상판의 중심점과 가장자리에서 동일한 분포를 하지 않는 결과를 얻었다. 양압력 분포특성은 잔교길이인 무차원(l/L), 파형경사(H/L), 공간(D/H)에 의해 영향을 받는다. 양압력에 영향을 미치는 무차원 요소(H/L)은 양압력의 최대치를 결정하는 D/H의 값이 존재하고 있다는 것을 알았다. 동일한 D/H인 경우도 양압력은 파형경사에 따라서 변화하고 있다. 즉, H/L이 클수록 (D/H)이 작기 때문에 잔교를 설계할 때 $D_{max}$가 되는 Clearance가 생기지 않는 상판높이를 정하는 것이 안전한 설계가 된다. 압축공기가 양압력에 미치는 영향을 검토한 결과 양압력이 크게 작용하는 On-shore에서는 Off-shore보다 압축공기에 의한 양압력의 저감효과가 크게 발생하고 있다. 상판에 작용하는 양압력을 저감시키기 위해서는 압축공기 유출을 방지하는 상판설계가 필요하다.

• 대한조선학회논문집
• /
• 제44권1호
• /
• pp.8-15
• /
• 2007

In this paper, numerical calculations are performed to analyze the unsteady flow of NACA airfoil sections. In order to ease the flow computation for the fluid region changing in time, improve the quality of solution and simplify the grid generation for the oscillating foil flow, the computational method adopts a moving and deforming mesh with the multi-block grid topology. The multi-block, structured-unstructured hybrid grid is generated using the commercial meshing software Gridgen V15. The MDM (Moving & Deforming Mesh) and the UDF (User Define function) function of FLUENT 6 are adopted for computing turbulent flows of the foil in pitching motion. Computed unsteady lift and drag forces are compared with experimental data. in general, the characteristics of unsteady lift and drag of the experiments are reproduced well in the numerical analysis.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.714-719
• /
• 2000

In this paper, an application program is made to simulate the behavior of a ship block under various crane works and to generate data of lu9 reactions and wire tensions. The program is based on a CAD program, Pro/ENGINEER. A ship is composed of more than 100 ship blocks. In order to lift, move, turn, or put a ship block at a convenient location fur assembling, workers in a shipyard use cranes, wires, and lugs temporarily attached to the block. In the procedure of lifting and turning a ship block with a crane, it is important to find suitable lug points and wires to do the handling efficiently and prevent accidents. Evaluation of forces in lugs and wires is necessary, but the problem is rather complex due to nonlinearity and nonuniqueness. In the present development, the nonlinear system of equations for quasi-static equilibriums is derived and a Newton type solution method is adopted to solve the system. The importance of initial estimates to the solution is illustrated and two approaches are utilized and compared. With the program developed, users can assign lug points on the CAD model by mouse and choose various linking devices at each crane point. Users can try to simulate the motion for any prescribed conditions, compare the motion of the block and the reactions and choose appropriate lug points and the type of wires and lugs.

• 설비공학논문집
• /
• 제23권4호
• /
• pp.251-258
• /
• 2011

The objective of this study is to propose two empirical correlations to predict the mass flow rate through an automotive block type thermostatic expansion valve and then to evaluate the correlations. The first correlation is deduced by modifying the basic equation of the orifice meter for the mass flow rate and the second correlation is deduced by using the Buckingham's ${\pi}$ theorem. The first correlation showed very good agreement on the measured data for R134a, given by Monforte. Average relative deviation and standard deviation of it are 2.5% and 1.6%, respectively. The second correlation agreed on the same measured data with a little greater deviations. The two correlations may apply to common expansion valves which have different geometrical sizes of the same shape.

• 한국주거학회논문집
• /
• 제15권2호
• /
• pp.97-105
• /
• 2004

This research is about Apartment Remodeling Upgrading Programme by Singapore Housing Development Board(HDB). For this study, we visited HDB and made field survey of the projects. There are basically three types of upgrading, namely, Precinct Upgrading, Apartment Block Upgrading and Flat Upgrading. Precint Upgrading refers the upgrading of services and facilities of the precinct. It involves the extention of open space, car-park, commercial space and additional covered linkways. These afford the residents greater convenience and comfort and generally enhance the environment of the community. Apartment Upgrading refers the upgrading of the block facade, improvements to the elevator, lift lobbies, letter boxes, trash chute and rain chute. The upgrading improves the quality of life of the residents. Flat Upgrading Involves the addition of space which may be in the form of a new Utility-room, replacement of old services, piping and equipment within an apartment unit. These provide the residents with a bigger and more comfortable living space.