• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.1
• /
• pp.1-11
• /
• 2016

We investigate compressive sensing techniques to estimate sparse channel in Orthogonal Frequency Division Multiplexing(OFDM) systems. In the case of large channel delay spread, compressive sensing may not be applicable because it is affected by length of measurement vectors. In this paper, we increase length of measurement vector adding pilot information to OFDM data block. The increased measurement vector improves probability of finding path delay set and Mean Squared Error(MSE) performance. Simulation results show that signal recovery performance of a proposed scheme is better than conventional schemes.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.37 no.1
• /
• pp.55-63
• /
• 2000

This paper investigated the sub-region compression effect of the three dimensional DCT(3D-DCT) using the difference component(DC) of inter-frame in images. The proposed algorithm are the method that obtain compression effect to divide the information into subband after 3D-DCT, the data appear the type of cubic block(8${\times}$8${\times}$8) in eight difference components per unit. In the frequence domain that transform the eight differential component frames into eight DCT frames with components of both spatial and temporal frequencies of inter-frame, the image data are divided into frame component(8${\times}$8 block) of time-axis direction into 4${\times}$4 sub block in order to effectively obtain compression data because image components are concentrate in corner region with low-frequency of cubic block. Here, using the weight of sub block, we progressed compression ratio as consider to adaptive sub-region of low frequency part. In simulation, we estimated compression ratio, reconstructed image resolution(PSNR) with the simpler image and the complex image contained the higher frequency component. In the result, we could obtain the high compression effect of 30.36dB(average value in the complex-image) and 34.75dB(average value in the simple-image) in compression range of 0.04~0.05bpp.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.6
• /
• pp.1763-1770
• /
• 2013

A series of the block copolymers were successfully synthesized from post-sulfonated hydrophilic and hydrophobic macromers via three-step copolymerization. The degrees of sulfonation (DS) of the copolymers (10%, 30%, or 50%) were controlled by changing the molar ratio of the hydrophilic and hydrophobic parts. The resulting block copolymers were characterized by $^1H$ NMR and other technologies. The membranes were successfully cast using dimethyl sulfoxide (DMSO) solution at $100^{\circ}C$. The copolymers were characterized to confirm chemical structure by $^1H$ NMR and FT-IR. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) demonstrated that all sulfonated block copolymers exhibited good thermal stability with an initial weight loss at temperatures above $240^{\circ}C$. The membranes showed acceptable ion exchange capacity (IEC) and water uptake values in accordance with DS. The maximum proton conductivity was 184 mS $cm^{-1}$ in block copolymer-50 at $60^{\circ}C$ and 100% relative humidity, while the conductivity of Nifion-115 was 160 mS $cm^{-1}$ under the same measurement conditions. AFM images of the block copolymer membranes showed well separated the hydrophilic and hydrophobic domains. From the observed results it is that the prepared block membranes can be considered as suitable polymer electrolyte membranes for the application of polymer electrolyte membrane fuel cells (PEMFC).

• Korean Journal of Geomatics
• /
• v.3 no.1
• /
• pp.73-79
• /
• 2003

To manage national territory and cadastral data efficiently, accuracy and cost-efficiency in cadastral boundary surveying is inevitable. The efficient management of cadastral data is a very important element in national land management. Survey techniques are being introduced. Recently, improvements in survey techniques have been made with the development of satellite surveying, Allowing accurate and fast surveys. If we can calculate the output accurately in real-time in survey fields, it will open a new method in cadastral detail surveying. According to the classification on Law of cadastral surveying, Cadastral surveying can be divided into cadastral control point surveying and cadastral detail surveying. The control point survey can be divided into cadastral triangulation surveying and cadastral traverse surveying. The detailed survey is usually perform by plane surveying. Among these, cadastral detail surveying will be reviewed in this study. In this study, the combination of the satellites, such as US managed GPS and Russian managed GLONASS was used. In the satellite survey in downtown, data interruption symptoms arose(according to the mask angle of the satellite). Therefore; we combined the satellites to get date more accurately. A block of Haewoondae New City in Busan, Korea, which has Numerical Cadastral Law was selected as the sample area for this study. Block II and III are surrounded by high rise apartments. One side of Block I and IV is level ground and the other side is full of high rise apartments. Especially, Block II is surrounded by high rise apartment houses with 20 meters width. In the results of the study Block II did not satisfy the allowable precision, while Block I, II and IV satisfied the allowable precision of the enforcement regulations of Cadastral Law. Therefore, it is judged that the traditionally used Total Station method should be used for supplementary survey on Block II, in stead.

• Journal of Korea Society of Industrial Information Systems
• /
• v.27 no.5
• /
• pp.25-36
• /
• 2022

This paper proposes a random sign reversal technique in space frequency block code for single carrier modulation. The traditional space time and frequency block coding technique may be confronted with radio environments openly, severe radio hijacking problems are to be overcome. In order to avoid such an open radio issue, random coded data protection technique for space-time block code was proposed, but this algorithm can change channel combination per an Orthogonal Frequency Division Multiplexing block. This kind of slow switching increases the probability that nearby receivers will detect the transmitted data. This paper proposes a fast switching algorithm per data symbols' basis which is a random sign reversal technique in space frequency block code for Single Carrier Modulation. It is shown in simulation that the proposed one has a superior performance in comparison with the performance of the receiver which do not know the random timing sequence of sign reversal.

• The Korean Journal of Pain
• /
• v.5 no.1
• /
• pp.76-79
• /
• 1992

Trigeminal neuralgia is a condition characterized by excruciating paroxysms of pain in lips, gums, cheek, or chin, and very rarely, in the distribution of the ophthalmic division of the trigeminal nerve. There are many treatments of trigeminal neuralgia, such as, medical treatment, electrical stimulation, radiation therapy and ablative procedures. Infraorbital nerve block with pure ethyl alcohol is an ablation procedure for trigeminal neuralgia. We injected pure ethyl alcohol into the infraorbital foramen for pain control. The results were as follows; 1) The infraorbital nerve block with pure alcohol was an a simple and an effective method. 2) Complication, included a mild sensory deficit and mild edema over the infraorbital area.

• ETRI Journal
• /
• v.20 no.1
• /
• pp.16-27
• /
• 1998

In this paper, we consider the acquisition performance of an IS-95 reverse link access channel slot as a function of system design parameters such as postdetection integration length and the number of access channel message block repetitons. The uncertainty region of the reverse link spreading codes compared to that of forward link is very small, since the uncertainty region of the reverse link is determined by a cell radius. Thus, the parallel acquisiton technique in the reverse link is more efficient than a serial acquisition technique in terms of implementation and of acquisition time. The parallel acquisition is achieved by a bank of N parallel I/Q noncoherent correlator are analyzed for band-limited noise and the Rayleigh fast fading channel. The detection probability is derived for multiple correct code-phase offsets and multipath fading. The probability of no message error is derived when rake combining, access channel message block combining, and Viterbi decoding are applied. Numerical results provide the acquisition performance for system design parameters such as postdetection integration length and number of access channel message block repetitions in case of a random access on a mobile station.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.41 no.5
• /
• pp.284-289
• /
• 2015

In cases of severe alveolar bone atrophy in the posterior maxillary area, which has only a thin sinus floor, the autogenous tooth bone graft block (ABTB) was used to wrap the implant to enhance its primary stability and osseointegration in the sinus. These cases with four years of clinical follow-up demonstrate the applicability of the ABTB in maxillary sinus membrane elevation to improve the outcomes of implant placement.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.249-251
• /
• 2008

In Factory Automation(FA) used by Programmable Logic Controller(PLC), Ladder Diagram(LD) is the most widely utilized and plays an important role in industrial control system. But recently, the study about Sequential Function Chart(SFC) is performed actively. When we program by SFC, generally, we design one routine from start to end. This method is difficult to design block control system, and we often make mistakes. In this paper, we propose the method that we design block control system and we analysis the difference of the method used this paper from conventional method.

• Design & Manufacturing
• /
• v.2 no.1
• /
• pp.1-5
• /
• 2008

Restriking method is to add to process in order to get the correct size and high precision accuracy of product which is formed in pre-process. This method is widely used at bending work and drawing work. Restriking die is particularly design and used as restriking process is performed. Therefore, production cost is increasing as one process or a two process are added. In this paper, punches and die block of square shell drawing die which could be performed drawing work and restriking process by using only one die are designed in order to solve these factors. The structure of sectional die which can integrate drawing die and restriking die was developed.