• Macromolecular Research
• /
• v.17 no.9
• /
• pp.682-687
• /
• 2009

Nanofibrous membranes of poly(D,L-lactic acid)/chitin blend were prepared by electro spinning for a barrier of guided tissue regeneration. A miscible solution was obtained by the blending chitin-salt complex into 1-methyl-2-pyrrolidone solution of poly(D,L-lactic acid). The properties of the blend were examined for nanofibrous fabrication. The viscosity of the blend solution was increased significantly due to chain entanglement despite the low ratio of chitin to poly(D,L-lactic acid). An interaction between two polymeric compositions was confirmed by Fourier transform infrared spectroscopy. X-ray diffraction detected an appreciably ordered microstructure in the nanofiber of the blend. A membrane of thinner nanofibers was fabricated by electro spinning the chitin blend. The permeability of the membranes was examined using bioactive model compounds.

• Elastomers and Composites
• /
• v.56 no.4
• /
• pp.234-242
• /
• 2021

The demand for truck bus radial (TBR) tires with enhanced fuel efficiency and wear resistance have grown in recent years. In addition, as the issue of particulate matter and air pollution increases, efforts are being made to reduce the generation of particulate matter. In this study, the properties of epoxidized natural rubber (ENR) containing a silica-friendly functional group were evaluated by considering it as a base rubber and varying the silica ratio in this binary filler system. The results showed that the wear resistance of the NR/BR blend compound decreased as the silica ratio increased. In contrast, the ENR/BR blend compound exhibited an increase in wear resistance as the silica ratio was increased. In particular, the ENR-50/BR blend compound showed the best wear resistance due to the presence of several epoxide groups. Furthermore, we observed that for tan 𝛿 at 60℃, higher epoxide content resulted in the higher T_g of the rubber, indicating a higher tan 𝛿 at 60℃. On the other hand, it was confirmed that increasing the silica ratio decreased the value of tan 𝛿 at 60℃ in all compounds. In addition, we measured the amount of wear particulate matters generated from the compound wear. These measurements confirmed that in the binary filler system, regardless of the filler type, the quantity of the generated wear particulate matters as the filler-rubber interaction increased. In conclusion, the silica filled ENR/BR blend compound exhibited the lowest generation of wear particulate matters.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.342-349
• /
• 1998

The objective of this study is to investigate the characteristic change of antiwashout underwater concrete with variation of blend ratio of sea sand and fine aggregate percentage through experimental researches. According to the experiments results, when sea sand are mixed in antiwashout underwater concrete mixture by about 40% per total fine aggregate, in fine aggregate percentage of 40%, it is found that the flowability fit and the compressive strength is higher others.

• Elastomers and Composites
• /
• v.39 no.2
• /
• pp.95-104
• /
• 2004

New compounds were made using various NR/BR blend ratio and oil content to improve mechanical properties of rubber isolator at low temperature. Mechanical properties were investigated as a function of NR/BR blend ratio and oil content. Hardness and tensile modulus generally increased, but tensile strength and elongation at break decreased with increasing BR content. Hardness, tensile modulus and tensile strength decreased, but elongation at break were nearly the same with increasing oil content. The glass transition temperature of NR and BR were found to be $-50^{\circ}C$ and $-90^{\circ}C$ respectively based on the abrupt drops in storage elastic modulus and peak of loss factor. Two distinct transition temperature were observed in NR/BR blend compounds and each transition point was not affected by blend level indicating incompatible nature of NR/BR blend.

• The International Journal of Costume Culture
• /
• v.8 no.1
• /
• pp.23-31
• /
• 2005

Mechanical properties and hand evaluation of wool/acrylic(W/A) blend knits were conducted before and after repeated washing to get the optimum W/A blending ratio, which could help achieve the optimum mechanical and hand properties of the knits. The five test fabrics using the yarns with different W/A blending ratios($\%$), 100/0, 70/30, 50/50, 30/70, 0/100, were knitted. The fabrics were washed by a rotating drum type washing machine. Then, objective mechanical and hand properties were evaluated by KES-FB, Kawabata evalution system for fabric. The results are as follows: there was no change in the hand value of the knitted fabric with the W/A-blended yarn caused by the change in the blending ratio before washing. After washing, however, the increase of acrylic's blending rate caused the bending property to decrease proportionally, while the friction coefficient of the surface property increased. Furthermore, the study showed that W/A 50/50 possesses the most superior tensile property and shearing property, which could attain the optimum blending ratio. Similar results in hand value were derived in all the samples. After washing, however, the increase in acrylic's blending rate caused a proportional decrease in KOSHI and an increase in FUKURAMI. In addition, W/A 50/50 gained the biggest NUMERI value, again corresponding to the optimum blending ratio. Similar results in total hand value were derived in all the samples before washing. After washing, though, all the total hand values decreased, and, as the wool fabric's blending rate increased, the total hand values proportionally decreased further.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.383-386
• /
• 2005

This paper is to investigate the effect of W/B, blend ratio of crushed sand with sea sand on fluidity and strength properties of high strength concrete utilizing crushed sand. W/B set up 0.25, 0.30, 0.35 and the blend ratio of crushed sand with sea sand set up 0:100, 30:70, 50:50, 70:30, 100:0 The results of this study are summarized as the follows; 1) The increase of the blend rate of crushed sand, affected on the enhancement of flow, the increase of dosage of SP and water content, but the decrease S/a 2) Compressive strength is increased when crushed sand $30\~70\%$ was replaced with sea sand. 3) The optimal replacement percentage of crushed sand is $50\%$ with sea sand.

• Journal of the Korean Ceramic Society
• /
• v.27 no.7
• /
• pp.833-840
• /
• 1990

For the development of multi-functional materials which has water reducing power, air entraining power and waterproofing power as well as blending additive in cement mortar the coal ash was modified with asphalt-stearic acid or asphalt-boiled oil mixtures by mechanical treatment. And the physical properties of cement mortar blended with modified coal ashes were compared with those of the water-tightness-cement mortar and the ordinary-portland-cement mortar added with AE.water reducing agent. The mortar of coalash-blend-cement modified with asphalt-stearic mixture was increased acid about 20% in initial strengths and decreased about 20% in water absorption ratio than those of ordinary coalash-blend-cement. The mortar of coalash-blend-cement modified with asphalt-bolied oil mixture was similar to the cement mortar added with AE.water reducing agent in water reduction ratio, air entraining conents and the initial strengths, also was similar to the water-tightness-cement mortar in water absorption and water permeability ratios.

• Membrane and Water Treatment
• /
• v.7 no.2
• /
• pp.155-173
• /
• 2016

The present work has been focused on the development of polysulfone (PSf) ultrafiltration membrane via blending by sulfonated polyethersulfone (SPES) in order to permeability enhancement for ultrafiltration of cheese whey. In this regards, sulfonation of polyethersulfone was carried out and the degree of sulfonation was estimated. The effect of blend ratio on morphology, porosity, permeation and fouling of PSf / SPES membranes was investigated. Filtration experiments of whey were conducted for separation of macromolecules and proteins from the lactose enrichment phase. The morphology and performance of membranes were evaluated using different techniques such SEM, AFM, and contact angle measurements. The contact angle measurement showed that the hydrophilicity of membrane was increased by adding SPES. According to AFM images, PSf / SPES membranes exhibited lower roughness compared to neat PSf membrane. The water and whey flux of these membranes were higher than neat membrane. However, flux was decreased when the PSf / SPES blend ratio was 0/100. It can be attributed to pore size and morphology changes. Further, fouling parameters of PSf membrane were improved after blending. The blend membranes show a great potential to be used practically in proteins separation from cheese whey.

• Journal of Environmental Health Sciences
• /
• v.23 no.3
• /
• pp.102-108
• /
• 1997

It has been studied that SO$_2$ removal efficiency of anthracite-bituminous coal blend combustion in a fludized bed coal combustor. The objectives of this study were to investigate SO$_2$ removal characteristics of coal blend combustion with Ca/S, anthracite fraction, bed temperature, and limestone size. The experimental results were presented as follows First, the effect of the desulfurization by the dia size of limestone was great and SO$_2$ removal efficiency was highest in limestone dia 631 $\mu$m. Second, as air velocity increased, the desulfurization rate decreased a little. But the difference of the desulfurization rate according to air velocity was not too large. As the height of fluidized bed combustor increased regardless of air velocity, SO$_2$ concentration tends to increase largely. Third, as Ca/S mole ratio incresed, SO$_2$ desulfurization rate incresed rapidly up to Ca/S mole ratio 3 while the desulfurization rates did not increse too largely in the range of more than the level. Forth, the bed temperature had a great effect on the desulfurization rate and the desulfurization rate tended to increase slightly as anthracite fraction increased.

• Textile Coloration and Finishing
• /
• v.26 no.1
• /
• pp.32-38
• /
• 2014

There has been increasing demand to the eco-friendly materials such as phytoncide which is extracted to plants in the textile industry, recently. It is interesting that alginic acid sodium salt(Alg-Na) is used to eco-friendly binder for the functional capsule finishing. In this study, we made PEO/Alg-Na blend solutions of various ratio and observed the changing binding property of the blend solutions according to PEO contents through FT-IR, DSC, contact angle, peel strength, etc. The viscosity of Alg-Na/PEO blend solutions increased with increase of contents and the viscosity quickly increased with increase of PEO content in Alg-Na 5% content, specially. It is shown that the hydrogen bond peak by blend of Alg-Na and PEO found through FT-IR analysis but the peak decreased in PEO above 60% content. And the peel strength was predominant in PEO 50% ratio.