• 한국안전학회지
• /
• 제23권4호
• /
• pp.99-104
• /
• 2008

본 연구에서는 저밀도 폴리에틸렌과 에털렌 비닐 아세테이트 블렌드(LDPF/EVA)의 난연성을 향상시키기 위해 난연제인 수산화 마그네슘과 난연상승보조제인 zinc borate를 첨가한 후, 난연성과 체적저항률, 유전정접, 교류 절연파괴강도 등의 전기적 특성, 인장강도 및 연신율 등의 가계적 특성을 비교 분석하여 가장 우수한 LDPF/EVA 블렌드의 혼합비 및 적절한 $Mg(OH)_2$의 zinc borate의 첨가량을 선정하고자 하였다. 혼합비 70/30phr의 LDPF/EVA 블렌드에 10phr의 $Mg(OH)_2$와 6phr 정도의 zinc borate를 첨가한 시편에서 가장 우수한 난연성 및 전기/기계적 특성을 나타내었다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제14권10호
• /
• pp.1419-1424
• /
• 2001

Previous research in our laboratory has demonstrated the importance of lactose in phase I and II pig starter diets. Two experiments were conducted to evaluate the use of a carbohydrate by-product (food by-products) as a replacement for lactose. In Exp. I, 120 weaned pigs ($14{\pm}2d$ and 5.65kg) were allotted in a randomized complete block design (RCBD) to 10 replications with four pigs per pen. This experiment evaluated three carbohydrate sources (lactose, carbohydrate by-product, and 50-50 blend of the carbohydrate by-product and lactose). The carbohydrate sources were added at 26% in the phase I diets and 15% in the phase II diets. Phase I diets contained 7.5% spray dried plasma protein (SDP). The phase I diets were fed from d 0 to 14 and the phase II diets from d 15 to 28. There were no significant differences between carbohydrate sources on pig performance in phase I. However, during phase II pigs fed the diet with lactose had an improved gain/feed ratio (G/F) (p=0.06) compared to pigs fed the carbohydrate by-product. For the entire 28 d trial ADG, ADFI and G/F were similar for the 50-50 blend and those fed lactose. Total replacement of lactose with the carbohydrate byproduct resulted in a reduced G/F (p=0.09). Exp. 2 used 100 weaned pigs ($17{\pm}2d$ and 4.75kg) with five replications with five pigs per pen. This experiment evaluated four carbohydrate treatments (lactose, carbohydrate by-products, 50-50 blend, and corn). All phase I diets contained 3.5% SDP with the carbohydrate sources included at 15%, and were fed d 0 to 14. The phase II diets contained 7.5% of the carbohydrate sources and were fed d 15 to 27. A common phase III diet was fed d 28 to 42. During all phases pigs fed com tended to have a lower ADG than pigs fed the other carbohydrate sources with the 50-50 blend resulting in the highest ADG. The results of both experiments suggest that this carbohydrate by-product can replace at least 50% of the lactose in phase I and phase II pig starter diets.

• 공업화학
• /
• 제10권8호
• /
• pp.1136-1140
• /
• 1999

폴리아마이드6(PA6)와 무수말레산이 그라프트된 폴리프로필렌(PP-g-MA)의 용융혼합된 블렌드계를 제조하고, 이 블렌드계의 인장, 굴곡, 충격, 동적기계적열 특성 및 상구조의 변화를 조사하였다. 인장강도와 인장탄성율은 두 조성물의 혼합에 따른 상승효과가 나타났고, 굴곡특성의 경우는 두 조성물의 산술평균값을 유지함을 알 수 있었다. 그리고 충격강도의 경우는 PA6/PP-g-MA 50/50 wt % 조성에서 최대값을 보였다. Tan ${\delta}$결과로부터, 두 조성물간의 반응에 의해 혼화성이 증가되었음을 확인하였다. 또한 상구조와 충격강도의 결과로부터, 본 블렌드계는 PA6 매트릭스에 PP-g-MA가 $2{\mu}m$정도 크기로 고르게 분산되어진 경우에 우수한 내충격성을 갖음을 알 수 있었다.

• Fibers and Polymers
• /
• 제6권2호
• /
• pp.121-126
• /
• 2005

Semicrystalline poly(ethylene terephthalate) (cPET)/amorphous poly(ethylene terephthalate) with isophthalic acid (aPET) blends with 100/0, 75/25, 50/50, 25/75, and 0/100 by weight ratios were dissolved in a mixture of trifluoroacetic acid (TFA)/methylene chloride (MC) (50/50, v/v) and electrospun via the electrospinning technique. Solution properties such as solution viscosity, surface tension and electric conductivity were determined. The solution viscosity slightly decreased as aPET content increased, while there was no difference in surface tension with respect to aPET composition. The characteristics of the electro spun cPET/aPET blend nonwovens were investigated in terms of their morphology, pore size and gas permeability. All these measurements were carried out before and after heat treatment for various blend weight ratios. The average diameter of the fibers decreased with increasing aPET composition due to the decrease in viscosity. Also, the morphology of the electrospun cPET/aPET blend nonwovens was changed by heat treatment. The pore size and pore size distribution varied greatly from a few nanometers to a few microns. The gas permeability after heat treatment was lower than that before heat treatment because of the change of the morphology.

• Elastomers and Composites
• /
• 제39권1호
• /
• pp.36-41
• /
• 2004

Poly(ethylene oxide)(PEO)와 epoxy diacrylate(EDA) 및 금속염인 LiClO_4$를 블렌드하고 자외선 가교시킴으로써 이온전도특성을 나타내는 고체 전해질을 제조하고, 제조된 전해질의 이온 전도도를 블렌드조성 염농도 및 온도 변화에 따가 측정하였다. PEO/EDA의 조성비가 70/30 wt%이고 ethylene $oxide/Li^+$의 몰비가 10인 전해질이 $25^{\circ}C$에서 $1.2{\times}10^{-5} S/cm$에 달하는 높은 이온전도도를 나타내었다. 제조된 전해질 필름은 투명하였으며 고무와 같은 탄성을 나타내었다. DSC, XRD 및 편광현미경을 이용한 모폴로지 분석으로부터 에폭시 사슬이 PEO의 결정화를 억제함으로써 완전히 무정형인 블렌드를 제조할 수 있음을 확인할 수 있었다.

• Elastomers and Composites
• /
• 제33권4호
• /
• pp.231-237
• /
• 1998

보강성 충전제가 첨가된 고무블렌드의 물리적 특성을 조사하기 위해 카본블랙이 첨가된 유화중합 고무블렌드와 실란이 커플링된 실리카가 첨가된 용액중합 고무블렌드의 가황특성, 점탄성특성, 내마모 및 고무보강성 평가하였다. 유화중합 고무블렌드는 가장 높은 총결합고무량을 나타냈으나, 용액중합 고무블렌드는 고무블렌드 비율에 관계없이 일정한 총결합고무량을 나타내었다. 고무의 미세구조중 비닐 및 스틸렌 함량이 낮을수록, 배합고무중 총결합고무량이 높을수록 가황속도는 빠르게 나타났으며, 고무보강성 지표인 모듈러스는 총결합고무량과 선형적인 관계를 나타냈다. 많은 PICO 손실량은 고무의 미세구조중 비닐 및 스틸렌 함량이 증가할 때 나타났으나, 적은 PICO 손실량은 실란이 커프링된 실리카를 함유한 용액중합 고무블렌드에서 부타디엔의 비율이 증가할 때 관측되었다. 용액중합 고무블렌드는 유화중합 고무블렌드에 비해 $0^{\circ}C$에서 높은 손실계수, $60^{\circ}C$에서는 낮은 손실계수를 나타내었다.

• 한국환경과학회지
• /
• 제9권6호
• /
• pp.511-515
• /
• 2000

The purpose of this experiment is to prepare ethylene propylene diene terpolymer(EPDM)/ acrylonitrile butadiene rubber(NBR) blend which represents good environmental resistant properties including favorable oil and ozone resistance. With incorporation of EPDM, NBR and other ingredients, the rubber and chemical additives were mixed by mechanical method such as Banbury mixer and open 2-roll mill. Then rubber vulcanizates were manufactured by hot press and mechanical properties, oil and ozone resistance of the test specimens were measured. The oil resistance and ozone resistance of EPDM and NBR, respectively, is remarkably improved by blending EPDM with NBR. The optimum results of oil and zone resistant characteristics were obtained at EPDM/NBR(=25/75 wt%) composition ratio.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권11호
• /
• pp.556-560
• /
• 2004

In this paper, thermal and structural properties of epoxy/elastomer blend were measured by DSC, TGA and FESEM. Specimens were made of dumbbell forms by the ratio of 5, 10, 15, and 20[phr] by changing elastomer content. The measuring temperature ranges of DSC were from -20[℃] to 150[℃] and heating rate was 4[℃/min]. And the measuring temperature ranges of TGA were from 0[℃] to 800[℃], and heating rate was 5[℃/min]. Also we observed structure of specimens through FESEM with magnification of 1000 times and voltage of 15[kV] by breaking quenched specimens. As experimental results, we could know that thermal and structural properties were improved according to decrease of elastomer content. Because it increased glass transition temperature, high temperature and structure of elastic epoxy.

• 한국전기전자재료학회논문지
• /
• 제15권2호
• /
• pp.153-161
• /
• 2002

Stable polyaniline-dodecylbenzenesulfonic acid(PANI-DBSA) fully dissolved in toluene was obtained by a direct one-step emulsion polymerization technique. By using the proper molar ratio of APS/aniline monomer and DBSA/aniline monomer, the highest conductivity(7 S/cm) of PANI was obtained. The UV-Vis absorption spectrum of PANI confirmed PANI is emeraldine salt form. PANI/styrene polymers (polystyrene and styrene-butadiene copolymer) blends were prepared by mixing PANI solution with polymers in toluene. These blends exhibited the conductivity of 10$\^$-4/-10$\^$-3/ S/cm at 1 wt. % of PANI content. The mechanical property of conducting blend was decreased and TGA thermograms of conducting blends were similar to that of PANI. It had been checked that the flatness of coating layers of conducting blends decreased with increasing conducting components. It was also found that the morphology of blends was setting closer to that of PANI at higher conducting component contents.

• Elastomers and Composites
• /
• 제29권2호
• /
• pp.121-130
• /
• 1994

The physical properties of rubber blend between natural rubber(NR) and ethylene propylene diene terpolymer(EPDM) were investigated as a study of EPDM composite materials. For EPDM/NR blends, the effects of ethylene and diene contents in EPDM, blend ratio, dicumyl peroxide(DCP) curing system on the physical properties, interfacial adhesion force and dynamic crack growth etc. were studied. EPDM/NR blends loaded with carbon black were prepared by mechanical mixing and cured by plate heating cure press. Crosslinking density was measured by swelling method with toluene. The physical properties of all blends were measured with Instron, fatigue to failure(FTF), Demattia flex cracking tester(DMFC), scanning electron microscopy (SEM), etc. As the ethylene and diene contents in EPDM increased, the physical properties, such as dynamic crack growth, adhesion to other component were increased too. Interfacial adhesion force of EPDM/NR blends to dissimilar layer was improved by the use of optimum peroxide curing system.