• Journal of the Korean Ceramic Society
• /
• v.32 no.10
• /
• pp.1178-1188
• /
• 1995

Bi4Ti3O12 (BIT) and its rare earth (Y, Nd, Sm, Gd)-substituted derivatives were synthesized using a sol-gel method to investigate their microstructures, cystal structures and electrical properties depending on the subsituted elemetns. Nd- or Sm-substitution into BIT appeared to be favorable, while Y- or Gd-substitution occurred with a pyrochlore phase. This suggests that a smaller trivalent rare earth ion may not be favorable in the structure of BIT. The rare earth derivatives showed that their particle sizes and shapes were considerably different depending on the kinds of substituted elements. Y-substitution resulted in developing a relatively even particle size and a dense microstructure. In structure, they may be similar to the pseudo-orthorhombic BIT but close to a paraelectric tetragonal phase. Their a (or b) axes were shortened, compared to the one of BIT. Such a distortion may result a decrease in the tilting of TiO6. BIT and the derivatives showed that their dielectric constants and losses were 40~120 and less than 0.03, respectively in the frequency range of 1~10 MHz. The dielectric loss of Y-substituted derivative was the lowest one and changed a little to frequency. Curie points were observed in all the derivatives like BIT to suggest that they would be ferroelectric. The temperature stability of the delectric properties of the derivatives below the Curie points were relatively better than the one of BIT.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.182-182
• /
• 2014

Multiferroic materials have attracted much attention due to their own fascinating fundamental physical properties and potential technological applications to magnetic/ferroelectric data storage systems, quantum electromagnets, spintronics, and sensor devices. Among single-phase multiferroic materials, $BiFeO_3$, in particular, has received considerable attention because the enhanced ferromagnetism was found by the Fe-site ion substitution with magnetic ions. The structural, the magnetic and the ferroelectric properties of polycrystalline $BiFe_{1-x}Ni_xO_3$ (x=0, 0.01, 0.02, 0.03 and 0.05), which were prepared by the solid-state reaction and the rapid-sintering method, have been investigated. The x-ray diffraction patterns reveal that all the samples are in single phase and show rhombohedral structure with R3c space group. The magnetic properties are enhanced according to the doping content. The Ni-doped $BiFeO_3$ samples exhibit lossy P-E loop due to the oxygen vacancy. The leakage current density of Ni-doped samples (x=0.01 and 0.02) is increased by four orders of magnitude. On the other hand, the x=0.03 and 0.05 samples show the relative reduction of the leakage current.

• Journal of information and communication convergence engineering
• /
• v.4 no.4
• /
• pp.158-161
• /
• 2006

[ $Bi_2Sr_2Ca_nCu_{n+1}O_y(n{\geq}0)$ ] thin film is fabricatedvia two different processes using an ion beam sputtering method i.e. co-deposition and layer-by-layer deposition. A single phase of Bi2212 can be fabricated via the co-deposition process. While it cannot be obtained by the layer-by-layer process. Ultra-low growth rate in our ion beam sputtering system brings out the difference in Bi element adsorption between the two processes and results in only 30% adsorption against total incident Bi amount by layer-by-layer deposition, in contrast to enough Bi adsorption by co-deposition.

• Journal of the Korean Ceramic Society
• /
• v.35 no.9
• /
• pp.1002-1005
• /
• 1998

Bismuth titanate thin films were prepared on {{{{ { SrTiO}_{3 } }}(100) and Si(100) substrates by dipping-pyrolysis pro-cess using metal naphthenates as starting materials. crystallinity and in-phase alignment of the films were analyzed by X-ray diffraction $\theta$-2$\theta$ scans and $\beta$ scans (pole-figures) respectively. Highly c-axis-oriented {{{{ { { {Bi }_{4 }Ti }_{3 }O }_{12 } }} thin films with smooth surfaces were obtained after heat treatment at 75$0^{\circ}C$ on {{{{ { SrTiO}_{3 } }}(100) sub-strate while the films grown of Si(100) exhibited polycrstalline characteristics. C-axis oriented film show-ed an epitaxial relationship with the {{{{ { SrTiO}_{3 } }} substrate.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.76-78
• /
• 1994

Owing to the discover of oxide superconducting over critical temperature100K, it is being made experimentally somewhere under the possibility that there is superconducting magnet by cooling liquid nitrogen. The issues of thermal stability and quench process of Low-Tc superconductor has been studied and used application of oxide superconducting magnets. However the quench propagation property of oxide superconductor, especially experimental data about thermal behavior has not been reported yet. Therefore we measured the effect of temperature dependance of quench propagation velocity, Vq, by using the short samples made up of silver sheathed Bismuth-family (2223phase) superconducting oxide tape.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.371-374
• /
• 2002

Bismuth lanthanum titanate thin films with excess Bi contents were prepared onto Pt/Ti/$SiO_2$/Si substrate by metalorganic decomposition (MOD) technique. The structure and morphology of the films were analyzed using X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. From the XRD analysis, BLT thin films show polycrystalline structure and the layered-perovskite phase was obtained over 10% excess of Bi contents. As a result of ferroelectric characteristics related to the Bi content of the BLT thin film, the remanent polarization and dielectric constant decreased with increasing over Bi content of 10 % excess. The BLT film with Bi content of 10% excess was measured to have a dielectric constant of n9 and dielectric loss of 1.85[%]. The BLT thin films showed little polarization fatigue test up to 3.5 x $10^{9}$ bipolar switching cycling.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.621-627
• /
• 1996

$SrBi_{2x}TaO_9$ ferroelectric thin films were prepared on platinized silicon substrates using MOD proces, and crystallization behavior of the films was investigated with variation of the annealing temperature and Bi content x. Crystalline phase of bismuth layered perovskite structure was formed even by baking the films at $800^{\circ}C$ for 5 minutes in air, and was not changed by annealing at temperatures raning from $700^{\circ}C$ to $900^{\circ}C$ for 1 hour in oxygen ambient. When $SrBi_{2x}TaO_9$ thin films ($0.8\lex\ie1.6$) were annealed at $800^{\circ}C$, Preferred orientation of the films along c-axis was observed with $x\ge1.2$. With increasing Bi content x, surface morphology of the films was changed from equiaxed grains to elongated grains.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.3
• /
• pp.103-108
• /
• 2009

The effect of Arsenic in copper-sulfate solutions during electrorefining of copper was investigated using scanning electron microscopy, X-ray diffraction and cyclic voltammetry analysis. Electrodeposition was carried out using Arsenic, Antimony and bismuth addition to sulfate electrolytes: 45 g/l $Cu^{2+}$ and 170 g/l $H_2SO_4$. Arsenic in sulfate electrolytes changed the morphology and structure of the copper deposits as compared with those obtained from impurity free solutions. When arsenic was present in the sulfate electrolytes, $Cu-3$As intermetallic phase was formed locally on the deposits.

• Journal of Korea Foundry Society
• /
• v.26 no.4
• /
• pp.191-196
• /
• 2006

The effects of Bi and Te on the anti-galling behaviors of Ni base alloy were investigated by SEM, galling test and wear test. Anti-galling characteristics depended on the structure of matrix and distribution of Bi-rich phase which was precipitated at grain boundary. The addition of 5 wt% Bi markably enhanced anti-galling properties. The addition of Te caused Bi-rich precipitates to disperse finely and casting structure to form equiaxed type. From the above tests, the concentration of 5 wt% Bi and 1 wt% Te was selected to optimize in this alloy.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.4
• /
• pp.160-165
• /
• 2015

Lead-free piezoelectric materials have been actively studied to substitute for conventional PZT based solid solution, $Pb(Zr_xTi_{1-x}O_3)$, which occurs unavoidable PbO during the sintering process. Among them, Bismuth Sodium Titanate, $Na_{0.5}Bi_{0.5}TiO_3$ (abbreviated as NBT) based solid solution is attracted for the one of excellent candidates which shows the strong ferroelectricity, Curie temperature (Tc), remnant polarization (Pr) and coercive field (Ec). Especially, the solid solution of rhombohedral phase NBT with tetragonal perovskite phase has a rhombohedral - tetragonal morphotropic phase boundary. Modified NBT with tetragonal perovskite at the region of MPB can be applied for high frequency ultrasonic application because of not only its low permittivity, high electrocoupling factor and high mechanical strength, but also effective piezoelectric activity by poling. In this study, solid state ceramic processing of NBT and modified NBT, $(Na_{0.5}Bi_{0.5})_{0.93}Ba_{0.7}TiO_3$ (abbreviated as NBT-7BT), at the region of MPB using 7 % $BaTiO_3$ as a tetragonal perovskite was introduced and the structure between NBT and NBT-7BT were analyzed using rietveld refinement. Also, the ferroelectric and piezoelectric properties of NBT-7BT such as permittivity, piezoelectric constant, polarization hysteresis and strain hysteresis loop were compared with those of pure NBT.