• Current Photovoltaic Research
• /
• v.4 no.2
• /
• pp.31-41
• /
• 2016

n-type PERT (passivated emitter, rear totally diffused) bifacial solar cells with boron and phosphorus diffusion as p+ emitter and n+ BSF (back surface field) have attracted significant research interest recently. In this work, the influences of wafer thickness, bulk lifetime, emitter, BSF on the photovoltaic characteristics of solar cells are discussed. The performance of the solar cell is determined by using one-dimensional solar cell simulation software PC1D. The simulation results show that the key role of the BSF is to decrease the surface doping concentration reducing the recombination and thus, increasing the cell efficiency. A lightly phosphorus doped BSF (LD BSF) was experimentally optimized to get low surface dopant concentration for n type bifacial solar cells. Pre-oxidation combined with a multi-plateau drive-in, using limited source diffusion was carried out before pre-deposition. It could reduce the surface dopant concentration with minimal impact on the sheet resistance.

• Current Photovoltaic Research
• /
• v.5 no.3
• /
• pp.89-94
• /
• 2017

We have examined the issues on the measurement of bifacial photovoltaic(PV) devices that should be considered in order to ensure a measurement accuracy beyond a certain level and the comparability between the bifacial PV devices. Based on the results of various experiments and previous studies, solutions for these measurement issues are suggested. The most significant technical issues in the performance measurement of the bifacial PV devices are 1) elimination of the effect due to the light reflection on the sample holder surface and 2) the measurement of the expected power generation gain in outdoor operation. The effect due to the light reflection on the sample holder surface can be eliminated by using an anti-reflective sample holder. In case of a reflective sample holder, if the bifacial device have a linear characteristic with respect to the irradiance of incident light, it has been confirmed (through some previous studies and additional experiment) that exact measurement results can be obtained by the correction of the measurement data. In addition, it was also confirmed that the expected power generation gain in the outdoor operation can be obtained by three different methods along with the basic concepts of the bifaciality coefficient, the albedo, and the effective front irradiance.

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1268-1274
• /
• 2018

We have investigated the effects of chemical rounding (CR) on the surface passivation and/or antireflection performance of $AlO_{x^-}$ and $AlO_x/SiN_x:H$ stack-passivated pyramid textured $p^+$-emitters with two different boron doping concentrations, and on the performance of bifacial n-PERT Si solar cells with a front pyramid textured $p^+$-emitter. From experimental results, we found that chemical rounding markedly enhances the passivation performance of $AlO_x$ layers on pyramid textured $p^+$-emitters, and the level of performance enhancement strongly depends on boron doping concentration. Meanwhile, chemical rounding increases solar-weighted reflectance ($R_{SW}$) from ~2.5 to ~3.7% for the $AlO_x/SiN_x:H$ stack-passivated pyramid textured $p^+$-emitters after 200-sec chemical rounding. Consequently, compared to non-rounded bifacial n-PERT Si cells, the short circuit current density Jsc of 200-sec-rounded bifacial n-PERT Si cells with ~60 and ${\sim}100{\Omega}/sq$ $p^+$-emitters is reduced by 0.8 and $0.6mA/cm^2$, respectively under front $p^+$-emitter side illumination. However, the loss in the short circuit current density Jsc is fully offset by the increased fill factor FF by 0.8 and 1.5% for the 200-sec-rounded cells with ~60 and ${\im}100{\Omega}/sq$ $p^+$-emitters, respectively. In particular, the cell efficiency of the 200-sec-rounded cells with a ${\sim}100{\Omega}/sq$ $p^+$-emitter is enhanced as a result, compared to that of the non-rounded cells. Based on our results, it could be expected that the cell efficiency of bifacial n-PERT Si cells would be improved without additional complicated and costly processes if chemical rounding and boron doping processes can be properly optimized.

• Korean Journal of Materials Research
• /
• v.30 no.5
• /
• pp.262-266
• /
• 2020

In this paper, we investigated the effect of the passivation stack with Al₂O₃, hydrogenated silicon nitride (SiN_x:H) stack and Al₂O₃, silicon oxynitride (SiON_x) stack in the n type bifacial solar cell on monocrystalline silicon. SiNx:H and SiON_x films were deposited by plasma enhanced chemical vapor deposition on the Al₂O₃ thin film deposited by thermal atomic layer deposition. We focus on passivation properties of the two stack structure after laser ablation process in order to improve bifaciality of the cell. Our results showed SiN_x:H with Al₂O₃ stack is 10 mV higher in implied open circuit voltage and 60 ㎲ higher in minority carrier lifetime than SiON_x with Al₂O₃ stack at Ni silicide formation temperature for 1.8% open area ratio. This can be explained by hydrogen passivation at the Al₂O₃/Si interface and Al₂O₃ layer of laser damaged area during annealing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.3
• /
• pp.182-187
• /
• 2018

In this study, 20.8% of a p-type Si bifacial solar cell was used to develop a photovoltaic (PV) module to obtain the maximum power under a limited installation area. The transparent back sheet material was replaced during fabrication with a white one, which is opaque in commercial products. This is very beneficial for the generation of more electricity, owing to the additional power generation via absorption of light from the rear side. A new model is suggested herein to predict the power of the bifacial PV module by considering the backside reflections from the roof and/or environment. This model considers not only the frontside reflection, but also the nonuniformity of the backside light sources. Theoretical predictions were compared to experimental data to prove the validity of this model, the error range for which ranged from 0.32% to 8.49%. Especially, under $700W/m^2$, the error rate was as low as 2.25%. This work could provide theoretical and experimental bases for application to a distributed and microgrid network.

• Current Photovoltaic Research
• /
• v.7 no.4
• /
• pp.97-102
• /
• 2019

Bifacial and semitransparent hydrogenated amorphous silicon (a-Si:H) thin-film solar cells in p-i-n configuration were prepared with front and rear transparent conducting oxide (TCO) electrodes using plasma-enhanced chemical vapor deposition method. Fluorine-doped tin oxide and tin-doped indium oxide films were used as front and rear TCO contacts, respectively. Film thickness of intrinsic a-Si:H absorber layers were controlled from 150 nm to 450 nm by changing deposition time. The dependence of performance characteristics of solar cells on the front and rear illumination direction were investigated. For front illumination, gradual increase in the short-circuit current density (J_SC) from 10.59 mA/㎠ to 14.19 mA/㎠ was obtained, whereas slight decreases from 0.83 V to 0.81 V for the open-circuit voltage (V_OC) and from 68.43% to 65.75% for fill factor (FF) were observed. The average optical transmittance in the wavelength region of 380 ~ 780 nm of the solar cells decreased gradually from 22.76% to 15.67% as the absorber thickness was changed from 150 nm to 450 nm. In case of the solar cells under rear illumination condition, the J_SC increased from 10.81 to 12.64 mA/㎠ and the FF deceased from 66.63% to 61.85%, while the V_OC values were maintained at 0.80 V with increasing the absorber thickness from 150 nm to 450 nm. By optimizing the deposition parameters, a high-quality bifacial and semitransparent a-Si:H solar cell with 350 nm-thick i-a-Si:H absorber layer exhibited the conversion efficiencies of 7.69% for front illumination and 6.40% for rear illumination, and average visible optical transmittance of 17.20%.

• Current Photovoltaic Research
• /
• v.9 no.4
• /
• pp.111-122
• /
• 2021

Silicon heterojunction technology (HJT) solar cells have received considerable attention due to advantages that include high efficiency over 26%, good performance in the real world environment, and easy application to bifacial power generation using symmetric device structure. Furthermore, ultra-highly efficient perovskite/c-Si tandem devices using the HJT bottom cells have been reported. In this paper, we discuss the unique feature of the HJT solar cells, the fabrication processes and the current status of technology development. We also investigate practical challenges and key technologies of the HJT solar cell manufacturers for reducing fabrication cost and increasing productivity.

• Current Photovoltaic Research
• /
• v.10 no.4
• /
• pp.116-120
• /
• 2022

Solar energy is rapidly being utilized to generate power in Europe and other countries, but the environmental effect of building and operating solar farms is not fully understood. The building of a solar park demands the removal of certain vegetation and the leveling of the land. Solar energy infrastructure may involve considerable landscape change, altering soil biological processes and influencing hydrologic, carbon and vegetative dynamics. To rebuild the solar PV facilities soils, inherent plant fields might require to be re-established. Within the scope of this research, we presented an analysis of the effects that were caused by the solar farm.

• Annals of Clinical Neurophysiology
• /
• v.24 no.1
• /
• pp.17-20
• /
• 2022

Facial diplegia (FD) rarely occurs as a regional Guillain-Barré syndrome (GBS) variant. A 70-year-old male presented with bifacial weakness that had started on the left side and extended to the right after several days. He was then treated using steroids and gradually improved. Serum antiganglioside antibody testing revealed positivity for anti-GM1 IgG antibodies. FD can be idiopathic, but it is an uncommon GBS variant. The ganglioside antibody test may increase the possibility of diagnosing isolated FD.

• Proceedings of the Korean Society of Plant Pathology Conference
• /
• 2003.10a
• /
• pp.93.1-93
• /
• 2003

A growth chamber fumigation was conducted to evaluate the ozone (O3) on the physiology of three hot pepper, Capsicum annuum L. cultivars, 'dabotab', 'buchon' and 'pochungchun'. Thirty-day old plants were exposed to O3 of 120 nl 1-1 in the chambers for 8 h d-1 for 3 days. Foliar damage due to O3 was different from the varieties, 'dabotab'was most sensitive to O3, 'pochungchun' was medium, and 'buchon' was resistant. Ozone symptom on the leaves was bifacial necorsis. Photosynthesis and stomatal conductance were decreased due to O3 treatment, but they were not much different from the variety. Decreases of net photosynthesis by O3 were 56％, 40％ and 35％ on 'dabotab', 'buchon' and 'pochungchun', respectively Decreases of stomatal conductance by O3 were 66％, 63％, and 50％ on each varieties. Ozone closed the stomata and decrease net photosynthesis on hot peppers regardless of the variety. Light curves on the three varieties were showing similar patterns that O3 damage on net photosynthesis were started at the low levels of light with or without the visible injury, Assimilation-internal CO2 concentration curves of the three cultivars were not different due to the treatment. It means there was not significant biochemical damage Inside the leaves by O3. In conclusion, ozone closed the stomata and damaged light capturing system of the pepper leaves with or without the visible damage. Although visible damage of the leaves could be a good indicator of O3 resistance, the ecophysiological change by O3 were not proportional to the amout of visible injuries