• 한국기계가공학회지
• /
• 제17권4호
• /
• pp.113-122
• /
• 2018

A hydraulic breaker is an attachment of an excavator, and it crushes stones. Recently, research to reduce the impact and noise of breakers are ongoing. In this paper, a method to improve the upper, lower, and side dampers, which act as insulation for the attenuation of vibration during breaker operation, is studied through testing and simulation. To obtain the nonlinear material constants required for the simulation, the biaxial tensile test was performed with urethane, which is a material used for dampers. The existing parts and the improved parts were compared and evaluated using the LS-DYNA program. As a result, 50% of the equivalent stress was reduced in the bracket body of the hydraulic breaker, and the equivalent stress of the side damper was also decreased. We verified that the fatigue conditions were satisfied by performing a fatigue analysis.

• Advances in concrete construction
• /
• 제14권5호
• /
• pp.317-330
• /
• 2022

This paper investigated computationally and experimentally the interaction here between a notch as well as a micropore under uniaxial compression. Brazilian tensile strength, uniaxial tensile strength, as well as biaxial tensile strength are used to calibrate PFC2d at first. Then, uniaxial compression test was conducted which they included internal notch and micro pore. Experimental and numerical building of 9 models including notch and micro pore were conducted. Model dimensions of models are 10 cm × 10 cm × 5 cm. Joint length was 2 cm. Joints angles were 30°, 45° and 60°. The position of micro pore for all joint angles was 2cm upper than top of the joint, 2 cm upper than middle of joint and 2 cm upper than the joint lower tip, discreetly. The numerical model's dimensions were 5.4 cm × 10.8 cm. The fractures were 2 cm in length and had angularities of 30, 45, and 60 degrees. The pore had a diameter of 1 cm and was located at the top of the notch, 2 cm above the top, 2 cm above the middle, and 2 cm above the bottom tip of the joint. The uniaxial compression strength of the model material was 10 MPa. The local damping ratio was 0.7. At 0.016 mm per second, it loaded. The results show that failure pattern affects uniaxial compressive strength whereas notch orientation and pore condition impact failure pattern. From the notch tips, a two-wing fracture spreads almost parallel to the usual load until it unites with the sample edge. Additionally, two wing fractures start at the hole. Both of these cracks join the sample edge and one of them joins the notch. The number of wing cracks increased as the joint angle rose. There aren't many AE effects in the early phases of loading, but they quickly build up until the applied stress reaches its maximum. Each stress decrease was also followed by several AE effects. By raising the joint angularities from 30° to 60°, uniaxial strength was reduced. The failure strengths in both the numerical simulation and the actual test are quite similar.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 가을 학술발표회논문집
• /
• pp.217-221
• /
• 2000

Nonlinear stress analysis of nuclear containment building wall element is carried out using microscopic material model. The present study mainly focuses on the finite element analysis of the nuclear containment building wall element under biaxial tensile stresses and it evaluates the perfomance of adopted microscopic material model in the membrane energy dominant situation. From the numerical analysis, the adopted material model peforms well and has a good agreement with experiment result. Finally, the result of present study can be severed as a benchmark test when concrete material model is in need of evaluation.

• 한국전기전자재료학회논문지
• /
• 제21권7호
• /
• pp.669-673
• /
• 2008

ITO thin film was deposited on PC substrate in Facing Targets Sputtering (FTS) system with various sputtering conditions. After it is applied to external bending force, we investigated how change the surface and electrical property of as-deposited ITO thin film. As the L(face-plate distance) of substrate decreases, it found that the maximum crack density is increasing at the center position and decreasing crack density as goes to the edge. So to apply same curvature (r) and bending force to PC substrate with ITO thin film, we fixed the L that is equal to curvature radius (2r). Before bending test, ITO thin films that deposited in the input current of 0.4 A and thickness of 200 nm already had biaxial tensile failure because of each different CTE (Coefficient of Thermal Expansion) and Others had been shown no bending or crack. After bending test, all samples had been shown cracks at about 200 times and as increasing the crack density, resistivity increased.

• Elastomers and Composites
• /
• 제40권2호
• /
• pp.119-127
• /
• 2005

고무부품의 신뢰성을 확보하기 위해서 고무재료의 물성파악과 수명평가는 매우 중요하다 하겠다. 본 연구에서는 냉장고 콤프레샤 모터에서 발생되는 소음 및 진동 제어 목적으로 고무마운트에 사용되는 고무재료인 NBR과 EPDM에 대해 상온과 $70^{\circ}C,\;85^{\circ}C,\;100^{\circ}C$에서 75일 동안 노화시킨 상태에서 단축 인장과 이축 인장으로 물성시험을 수행하여 가교밀도, 100% 모듈러스 변화와 응력-변형률 관계를 파악하였다. 또한, 고무소재의 노화수명을 예측하기 위해 가속열 노화시험을 수행하여 시간-온도 환산식인 아레니우스 관계식을 구하였다.

• Smart Structures and Systems
• /
• 제23권5호
• /
• pp.479-493
• /
• 2019

In this paper, the interaction between notch and micro pore under uniaxial compression has been performed experimentally and numerically. Firstly calibration of PFC2D was performed using Brazilian tensile strength, uniaxial tensile strength and biaxial tensile strength. Secondly uniaxial compression test consisting internal notch and micro pore was performed experimentally and numerically. 9 models consisting notch and micro pore were built, experimentally and numerically. Dimension of these models are 10 cm*1 cm*5 cm. the length of joint is 2 cm. the angularities of joint are $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$. For each joint angularity, micro pore was situated 2 cm above the lower tip of the joint, 2 cm above the middle of the joint and 2 cm above the upper of the joint, separately. Dimension of numerical models are 5.4 cm*10.8 cm. The size of the cracks was 2 cm and its orientation was $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$. Diameter of pore was 1cm which situated at the upper of the notch i.e., 2 cm above the upper notch tip, 2 cm above the middle of the notch and 2 cm above the lower of the notch tip. The results show that failure pattern was affected by notch orientation and pore position while uniaxial compressive strength is affected by failure pattern.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.295-299
• /
• 2006

The inner-structure bonded(ISB) sheet metal is defined as a composite sheet metal which has middle layer of truss-structure between two skin sheets. The characteristics such as ultra-light weight, high rigidity, high strength, etc are required especially for automobile parts. The characteristic of ISB sheet metal depends on inner-structure pattern or method of bonding. Pyramid type of crimped expanded metal is used for inner-structure and both of resistance welding and adhesive bonding are applied to make a specimen. As a result of compression test, it is appeared that forming limit is 10% reduction in thickness under a load of 8kgf per unit element(one inner-structure). In case of uniaxial tensile test the non-uniform surface integrity rather than the buckling of inner-structure happened at a load of 450kgf, which indicates elongation of 7.2% and thickness reduction of 13%. The eye-inspection method was applied to examine the defects occurring on the specimen during stretch forming. In case of biaxial stretch forming only the non-uniform deformation on the surface of a skin sheet could be observed. The forming limit in stretching of ISB sheet metal with the hemi-spherical punch of 150mm in diameter was 3mm in forming depth and 5% reduction in thickness.

• 한국지반공학회지:지반
• /
• 제14권5호
• /
• pp.219-234
• /
• 1998

초기수평 응력상태를 모사하여 응력이 변형계수에 미치는 영향을 검토 하기 위하여 암석 시료에 대하여 공내재하 변형 실내시험을 했다. 실험은 수평 응력의 크기, 응력비, 측정지점을 변화 시켜서 변형계수를 측정하였다. 측정결과 응력의 크기가 증가함에 따라 변형계수가 증가하며 최대 최소응력비가 커짐에 따라 변형계수는 최소응력 방향에서는 증가하고, 최대응력 방향에서는 감소하는 경향을 보였다. 이는 측정 위치에서 접선음력의 크기 변화에 따른 것으로 초기응력의 크기, 방향 및 내압의 크기에 따라 응력이 압축, 인장 또는 압축-인장상태로 바뀌기 때문이다. 따라서 변형 계수 측정시 이들의 영향을 분석한 후 결과치를 해석하여야 한다. 이와 같은 해석은 공내재하 변형 측정 결과 뿐만 아니라 내압이 있는 가스 저장 또는 압축터널 설계 및 터널 계측 결과 해석에도 적용 되어야 한다.

• Journal of Chest Surgery
• /
• 제42권5호
• /
• pp.566-575
• /
• 2009

배경: 심장 판막의 기능은 대부분 판엽의 성질에 의해 결정된다. 단방향성 압력 장력 검사로 광범위하게 연구 되었으나, 단방향성 압력 장력 검사는 자연 상태에서의 압력 부하를 측정할 수 없다. 이번 연구는 더 나은 이종 이식 판막의 개발을 위하여 돼지의 대동맥 판막과, 폐동맥 판막을 고정액에 따라 자연적인 상태에서의 물리적 변화 즉 앙방향성 압력-팽창성 변화를 알아 보고자 하였다. 대상 및 방법: 돼지의 대동맥 판막과 폐동맥 판막을 아무것도 처리하지 않은 신선한 판막과 글루타알데하이드(glutaraldehyde, GA)로 고정한 군, GA에 에탄올과 같은 용매로 고정한 군으로 나누어 판막의 방사방향과 원주 방향의 양방향성 압력-신장도 변화를 조사 비교하였다. 결과: 신선한, GA고정 후의, 그리고 GA+ 용매 고정 후의 대동맥 판막(p=.00), 폐동맥 판막(p=.00) 모두에서 방사방향이 원주방향보다 압력 증가에 따라 더 잘 늘어 났다. GA 고정 후와 GA+용매 고정후의 대동맥 판막이 폐동맥 판막보다 각각 원주 방향과, 방사방향 비교했을 때 폐동맥 판막이 같은 압력에 대해 더 많이 늘어 났다(p=.00). 돼지의 신선한 대동맥 판막을 GA 고정 후에 원주 방향과 방사 방향에서 모두 신장도가 유의하게 감소 하였다(p=.00). GA+용매 고정 시에 방사 방향에서는 신장도가 유의하게 감소 하였으나(p=.00), 원주 방향에서는 그렇지 않았다(p=0.785). 그리고 GA 고정 그룹과 GA+용매 그룹간의 비교에서 원주 방향(p=0.785), 방사방향(p=0.137), 신장도가 유의한 차이는 얼었다. 폐동맥 판막에서도 GA 고정 그룹과 GA+용매 그룹간의 비교에서 원주 방향(p=0.718), 방사방향(p=0.910), 신장도가 유의한 차이는 없었다. 걸론: 돼지의 대동맥 판막과 폐동맥 판막의 GA 고정 시, 용매의 첨가는 물리적 손실은 가져 오지 않으나 신장도는 더 나아지지 않았다. 돼지의 대동맥 판막과 폐동맥 판막은 고정방법에 관계 없이 방사방향 신장도가 원주 방향보다 더 낫다.