• Journal of Powder Materials
• /
• v.15 no.5
• /
• pp.352-358
• /
• 2008

The present study focused on the synthesis of a bismuth-antimony-tellurium-based thermoelectric nanopowders using plasma arc discharge process. The chemical composition, phase structure, particle size of the synthesized powders under various synthesis conditions were analyzed using XRF, XRD and SEM. The powders as synthesized were sintered by the plasma activated sintering. The thermoelectric properties of sintered body were analyzed by measuring Seebeck coefficient, specific electric resistivity and thermal conductivity. The chemical composition of the synthesized Bi-Sb-Te-based powders approached that of the raw material with an increasing DC current of the are plasma. The synthesized Bi-Sb-Te-based powder consist of a mixed phase structure of the $Bi_{0.5}Sb_{1.5}Te_{3}$, $Bi_{2}Te_{3}$ and $Sb_{2}Te_{3}$ phases. This powder has homogeneous mixing state of two different particles in an average particle size; about 100nm and about 500nm. The figure of merit of the sintered body of the synthesized 18.75 wt.%Bi-24.68 wt.%Sb-56.57 wt.%Te nanopowder showed higher value than one of the sintered body of the mechanically milled 12.64 wt.%Bi-29.47 wt.%Sb-57.89 wt.%Te powder.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.95-103
• /
• 2021

Sn-58Bi-xRu composite solders were prepared by adding Ru nanoparticles to Sn-58Bi, a typical low-temperature solder, and the interfacial reaction and solder joint reliability were analyzed by reacting with Cu/OSP and ENIG surface treated PCB boards. The Cu₆Sn₅ IMC formed by the reaction with Cu/OSP had little change in thickness depending on the Ru content, and ductile fracture occurred inside the solder during the high-speed shear test without any significant change even after 100 hr aging. In reaction with ENIG, the Ni₃Sn₄ IMC thickness tended to decrease as the Ru content increased, and ENIG-specific brittle fracture was found in some specimens. Since Ru element is not found near the interface, it is judged not to be significantly involved in the interfacial reaction, and it is analyzed that it mainly exists together with the Bi phase.

• Progress in Superconductivity
• /
• v.4 no.2
• /
• pp.162-167
• /
• 2003

The critical current value of Bi-2223/Ag tape can be influenced by various factors. In particular, it was known that properties of precursor powders could affect the formation of Bi -2223 and grain growth rate of the same. Since, moistures and organic matters can easily contaminate the precursor powders of Bi-2223 tapes and degrade properties of superconductors, the precursor powders should be kept in optimal conditions to minimize contamination. In this study, the effect of moisture and organic matters has been investigated. A Bi-2223/Ag tape contaminated with a large amount of moisture and organic matter has been characterized by low critical current values and bubbling. It has been found that as the quantity of moisture increases, the Bi-2223 phases are formed at lower temperature and the amount of non-superconducting phase increases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.478-481
• /
• 2002

We carried out the experiments for fabricating $Bi_{2}Sr_{2}Ca_{2}Cu_{3}O_{x}$(Bi2223) superconductor thick films on Cu tapes. Cu-free (Bi,Pb)-Sr-Ca-0 powder mixtures were screen- printed on Cu tapes and heat-treated at 840-$860^{\circ}C$ for several minutes in air. Surface microstructures and phases of films were analyzed by XRD and optical microscope. The electric properties of superconducting films were examined by the four probe method. At heat-treatment temperature, the printing layers were in a partially molten state by liquid reaction between CuO in the oxidized copper tape and the precursors which were printed on Cu tapes. During the heat-treatment procedure, it is thought that Bi2223 superconducting particles nucleate at interfaces between Bi2212 phase and liquid.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.96-98
• /
• 2003

Many of research efforts have been focused on the improvement of critical current density Jc of silver-sheathed Bi-2223 tapes for practical applications of material. Bi-2223 superconducting wires with 55 filaments were fabricated by stacking, drawing process with different heat-treatment histories. After rolling process, Bi-2223 tapes were heat-treatment at 780~826$^{\circ}C$ with variable mass flow rate of mixed gas. In this study, the effect of changes in the variable mass flow rate of mixed gas during the heat treatment of Bi-2223/Ag tapes has been investigated. Distinct differences were observed in the Bi-2223 phase and critical current as flow rate of mixed gas. We could achieve proper conditions of mass flow rate of mixed gas for Ag-alloy clad Bi-2223 superconducting tapes.

• Journal of Magnetics
• /
• v.16 no.1
• /
• pp.19-22
• /
• 2011

[ $BiFeO_3$ ]is a multiferroic material that attracts attentions of many research groups due to its potential as being ferroelectric and ferromagnetic above room temperature. We have prepared both undoped- and Mn-doped $BiFeO_3$ by sol-gel auto-ignition method. Doping of Mn has resulted in decreasing grain size from 60 to 32 nm. X-ray diffraction data show that the samples are pure and single-phase. Infrared measurements on $BiFeO_3$ and Mn-doped $BiFeO_3$ revealed intrinsic stretching vibrations of tetrahedral sites of $Fe^{3+}$-O and of octahedral $Bi^{3+}$-O as well. On the other hand, as the Mn concentration increases, the magnetic moment of $BiFeO_3$ increases. It gives some suggestions in manipulating structural and magnetic properties of $BiFeO_3$ by doping Mn.

• Korean Journal of Materials Research
• /
• v.6 no.1
• /
• pp.90-98
• /
• 1996

Mn((Cu0.66AI0.34)1-x(Bi0.3Sb0.7)x) 및 Mn((Fe0.66AI0.34)1-x(Bi0.3Sb0.7)x) 합금계의 상의 변화와 자기적 특성을 조사하였다. Mn((Cu, SI)(Bi, Sb)) 합금계는 Bi상, MnSb상, MnBi상, k-상, Heuser상, Mn2Sb 및 $\beta$-Mn상의 혼합상으로 이루어졌으며 x가 증가함에 따라 Bi상과 Mn2Sb상이 증가하고 K-상, Heusler상 및 $\beta$-Mn상이 줄어들거나 사라졌다. 자기적 성질은 자성을 띄는 MnSb상, MnBi상, Mn2Sb상, k-상 및 Hseusler상과 비자성인 Bi상과 $\beta$-Mn상의 상대적 분율에 의해 결정됨을 알 수 있었고, 150K-200K 부근에서 그 이하로 온도가 감소함에 따라 자화값이 급격히 감소하는 현상이 나타났다. Mn((Fe, AI)(Bi, Sb))합금계는 Bi상, MnSb상, MnBi상, MnBi상,$\beta$-Mn상, k-상 및 Mn2Sb상의 혼합상으로 나타났으며, 자기적 성질은 조사한 전 조성에서 강자성을 띄고 있음을 알 수 있었다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.4
• /
• pp.353-358
• /
• 2012

In this paper, three-phase power equalizing system (PES) with UPS function is proposed. This system is based on NiMH battery with battery management system. The power conversion circuit is composed with the three-phase converter/inverter, the bi-directional converter, and the thyristor switches. The three-phase converter/inverter provides the power to the grid or get the power from the grid. Also, it operates as a UPS. The bi-directional converter charges or discharges the battery. The thyristor switches are used for connecting/disconnecting with the grid and the load. A 15 kW prototype is implemented for the verifying the performance of the proposed system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.474-477
• /
• 2002

We performed a continuous heat treatment experiment for long Si$_2$Sr$_2$CaCuO$_{x}$ (Bi2212) superconductor tapes on copper substrates. A precursor that contains a mixture of Bi$_2$O$_3$, SrCO$_3$, and CaCO$_3$ powders was prepared and screen-printed on Cu tapes. The screen- printed tapes were thermally treated by consecutive processes with various temperature settings using an air-filled tube furnace. The diffraction patterns and the microstructures of the high temperature superconductor thick films were analyzed by X-ray diffractometry (XRD) and optical Microscopy respectively, and the critical temperatures of the superconducting thick films were measured. The critical temperatures of the superconducting films were measured to be about 77K, and the films'crystallographic c-axes were confirmed to be normal to the film surfaces by XRD and morphology observation. We also observed that the thick superconducting layer is formed and aligned on the copper substrate via partial melted state that consists of a liquid phase and a secondary phase.e.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.222-228
• /
• 2012

This paper presents a design and simulation of bi-directional DC/DC boost converter for a fuel cell system. In this paper, we analyze the equivalent model of both a boost converter and a buck converter. Also we propose the controller of bi-directional DC-DC converter, which has buck mode of charging a capacitor and boost mode of discharging a capacitor. In order to design a controller, we draw bode plots of the control-to-output transfer function using specific parameters and incorporate 3pole-2zero compensator in a closed loop. As a result, it has increased PM(Phase Margin) for better dynamic performance. The proposed bi-directional DC-DC converter's 3pole-2zero compensation method has been verified with computer simulation and simulation results obtained demonstrates the validity of the proposed control scheme.