• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.4A
• /
• pp.245-253
• /
• 2012

In the longway tunnel and underground traffic road, the structure of transverse ventilation system is constructed by the airpit slab. In this study, the full scale specimens of the PSC airpit slab that attached fire resistance panel are performed the static and dynamic loading tests for evaluation of bending capacity. The first of all, it confirmed the evaluations about the fundamental efficiency of the fire resistance panel and PSC slab by the 3-point bending test and pull-off test. The tests are performed for evaluation of the bending resistance under ultimate static load and the bonded capacity under dynamic fatigue load. A fatigue test is performed for an investigation of the effect on wind pressure that is developed by transit of traffic. The damage or debonding on surface between fire resistance panel and PSC slab was not developed in dynamic fatigue load test, also the behavior of the specimens is very stable and the debonding of the fire resistance panel attached at the bottom surface of PSC slab was not developed in static load test, too. Therefore, the crack or debonding of the fire resistance panel will be not developed by external loads during the construction or completion of the precast fire resistance system.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.133-133
• /
• 2017

Lodging is one of the important constraints in rice production. The lodging destroys the canopy structure, and sharply reduces the capacity of photosynthetic rate and dry matter production. In cereal crops, stem lodging can be classified into two types: stem breaking type and stem bending type. To improve stem lodging resistance, it is important to reveal strong culm traits of superior lodging resistant varieties. There are large varietal differences in parameters associated with the bending moment at breaking (M) and flexural rigidity (FR). The indica variety Takanari possesses large M due to its large section modulus (SM) despite of its small bending stress (BS), while Takanari also has large FR due to its large secondary moment of inertia (SMI) and Young's modulus (YM). To identify quantitative trait loci (QTLs) and the corresponding genes associated with the parameters for M ($=SM{\times}BS$) and FR ($=SM{\times}YM$) should enable to develop lodging resistant varieties, efficiently. In order to identify QTLs for cell wall materials such as cellulose, hemicellulose and lignin associated with BS and YM, a set of Chromosome Segment of Substitution Lines (CSSLs) consisted of 37 lines with chromosome segments of Koshihikari in the genetic background of Takanari were used. Takanari had large M and small BS as compared with Koshihikari. The QTLs for BS were estimated on chromosomes 3, 5, 6, 8, 9, 10, 11 and 12. Koshihikari alleles increased BS in these QTLs. Takanari had a large FR due to its large SMI and YM as compared with Koshihikari. The YM was increased by substitution of the Koshihikari chromosomal segments on chromosomes 2, 10 and 11. Other QTLs estimated on chromosomes 7 and 12 that Koshihikari alleles contributed to the decrease of YM. For lignin, only one major QTL for lignin density was detected on chromosome 11. Hollocellulose densities were increased by the substitution of Koshihikari segments on chromosomes 5 and 11. On the other hand, these were decreased on chromosomes 1 and 3 by substitution of Koshihikari segments. QTLs for cellulose density were estimated on chromosomes 1, 3 and 5 by substitution of Koshihikari segments. For hemicellulose, QTL on chromosome 3 showed that hemicellulose density decreased by the substitution of Koshihikari segment. However, hemicellulose densities on chromosomes 5, 8 and 11 showed the opposite effects. The QTLs for hemicellulose, cellulose, and hollocelulose densities identified on chromosome 5 overlapped with that for bending stress, indicating the positive effect of Koshihikari segment on increasing bending stress. These results suggest that some QTLs for the densities of cell wall materials contribute to increasing bending stress and Young's modulus, and could be utilized to improve the lodging resistance for both types of breaking and bending in rice varieties.

• Journal of the Korean Society of Safety
• /
• v.30 no.3
• /
• pp.7-12
• /
• 2015

CFRP composites are used as primary structural members in various industrial fields because their specific strength and specific stiffness are excellent in comparison to conventional metals. Their usage is expanding to high added-value industrial fields because they are more than 50% lighter than metals, and have excellent heat resistance and wear resistance. However, when CFRP composites suffer impact damage, destruction of fiber and interface delamination occur. This causes an unexpected deterioration of strength, and for this reason it is very difficult to ensure the reliability of the excellent mechanical properties. Therefore, for the destruction mechanism in bending with impact damage, this study investigated the reinforcement data regarding various external loads by identifying the consequential strength deterioration. Specimens were damaged by impact with a steel ball propelled by air pressure. Decrease in bending strength caused by the tension and compression of the impact side, and depending on the lamination direction of fiber and interface inside the specimen. From the bending test it was found that the bending strength reduced when the impact energy increased. Especially in the case of compression on the impact side, as tensile stress occurred at the damage starting point, causing rapid failure and a substantially reduced failure strength.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.51 no.3
• /
• pp.71-78
• /
• 2009

Pipe section of bending part at the arch type pipe-house showed an ellipse with oblateness of 0.076 on the average. Flexural rigidity of bending part decreased by average 6.3% than that of an original round shape section. The deflection of arch type pipe-house measured by model experiments showed much bigger than the result of structural analysis. In case of arch type pipe-house, we supposed that the decrease of flexural rigidity for the bending part of pipes had an effect on deflection of roof under the working load. This effect should be considered in the structural analysis. Bending resistance of gable type pipe-house used a prefabricated connector which developed in this study showed about $1.5{\sim}1.8$ times stronger than that of the existing arch type or gable type processed bending. Therefore, we supposed that the gable-roofed prefabricated pipe-house is safer than arch type or bent gable type in case of heavy snowfall. According to house scales and section properties of steel pipe in use, safe snow depths and rafter intervals were presented for design of gable-roofed prefabricated pipe-house. Their standards were established in the range of the durable models recommended by RDA, and the comparative examinations were conducted by means of structural analysis. It was evaluated that the developed greenhouse model had a high applicability in the field.

• Fire Science and Engineering
• /
• v.1 no.1
• /
• pp.19-26
• /
• 1987

In this study, fire resistance of steel fiber reinforced concrete was investigated Cylindrical and prismatic specimens made of Ordinary Portland Cement plain concrete and steel fiber reinforced concrete were exposed to heating in accordance with a standard time-temperature curve as specified in KS·F22 57, method of fire resistance test for structural parts of buildings, the period of heating was 1 hour and 2 hours. After the fire resistance test, mechanical properties of specimens such as compressive and bending strength, stress-strain curve, static and dynamic modulus of elasticity and bending toughness were investigated. Also the cracks and spallings of the specimens were observed. From the test results, it was confirmed that steel fiber reinforced concrete has a excellent fire resistance than plain concrete in the view of higher residual strength of concrete and smaller crackings because of steel fibers in concrete.

• Structural Engineering and Mechanics
• /
• v.49 no.2
• /
• pp.273-283
• /
• 2014

According to deformation features of pre-twisted bar, its elastic bending and torsion buckling equation is developed in the paper. The equation indicates that the bending buckling deformations in two main bending directions are coupled with each other, bending and twist buckling deformations are coupled with each other as well. However, for pre-twisted bar with dual-axis symmetry cross-section, bending buckling deformations are independent to the twist buckling deformation. The research indicates that the elastic torsion buckling load is not related to the pre-twisted angle, and equals to the torsion buckling load of the straight bar. Finite element analysis to pre-twisted bar with different pre-twisted angle is performed, the prediction shows that the assumption of a plane elastic bending buckling deformation curve proposed in previous literature (Shadnam and Abbasnia 2002) may not be accurate, and the curve deviates more from a plane with increasing of the pre-twisting angle. Finally, the parameters analysis is carried out to obtain the relationships between elastic bending buckling critical capacity, the effect of different pre-twisted angles and bending rigidity ratios are studied. The numerical results show that the existence of the pre-twisted angle leads to "resistance" effect of the stronger axis on buckling deformation, and enhances the elastic bending buckling critical capacity. It is noted that the "resistance" is getting stronger and the elastic buckling capacity is higher as the cross section bending rigidity ratio increases.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.4
• /
• pp.47-52
• /
• 2017

Recently, a great attention has been paid to the mechanical behavior of ITO (Indium Tin Oxide) film, which is widely used in current smart devices due to its excellent electrical properties and transparency. In this study, the reliability of ITO thin films on flexible substrates was investigated using bending test and bending fatigue test. According to the relative position of ITO and substrate, the experiment was conducted on both outer and inner bending conditions. Inner bending condition exhibited superior electrical stability compared to outer bending test. The electrical resistance during outer bending fatigue test significantly increased compared to that in the inner bending fatigue. The crack nucleation and propagation differs according to the stress state and they have a great influence on the electrical resistance. The crack morphologies were observed by scanning electron microscopy.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.6
• /
• pp.632-640
• /
• 2019

Desalination plant ships have been recently regarded as one of the probable solutions for drought seasons in many countries. Because desalination plants should be mounted on the desalination ships and special purpose storages such as salty waste water tanks are necessary, onboard and compartment arrangements would be distinguished from those of other conventional commercial ships. This paper introduces some basic design procedure including resistance/propulsion and seakeeping performances. The ship lines were improved step by step after modification of the ship lines and verification of resistance/propulsion performances using computational fluid dynamics (CFD). After finalization of the ship lines, the seakeeping performance was also evaluated to check motion behaviors and drive wave-induced loads such as the wave shear force and bending moment. It was proved that the predicted long-term vertical wave shear force and bending moment were significantly less than the rule-based ones, thus it is expected that the deliverables of this study will reduce the construction cost of desalination plant ships.

• Journal of Korea Foundry Society
• /
• v.38 no.1
• /
• pp.16-26
• /
• 2018

In this study, the effects of the pouring temperature, preheating temperature, surface condition and fraction of the wear resistant part on the production of duo-castings were investigated using a high Cr white cast iron with excellent abrasion resistance and a low Cr alloy steel with good toughness. The constituent materials of the duo-castings were designed to have high hardness, fracture toughness and abrasive wear resistance for the replacement of high Mn alloy steels with low abrasive wear resistance. In particular, the amount of abrasive wear of 17% Cr white cast iron was about 1/20 of that of high Mn alloy steel. There was an intermediate area of about 3mm due to local melting at the bonding interface of the duo-castings. These intermediate regions were different from those of the constituent materials in chemical composition and microstructure. This region led to fracture within the wear resistant part rather than at the bonding interface in the bending strength test. The bending fracture strengths were 516-824 MPa, which were equivalent to the bending proof strength of high Mn steel. The effects of various casting conditions on the duo-cast behavior were studied by simple pouring of low Cr alloy steel melt, but the results proved practically impossible to manufacture duo-castings with a sound bonding interface. However, the external heating method was suitable for the production of duo-castings with a sound bonding interface.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.65-66
• /
• 2023

Recently, the importance of improving air quality has been greatly highlighted due to environmental problems such as indoor air pollution, and efforts are being made to improve indoor air quality not only in Korea but also around the world. In this situation, this study aims to study the physical properties of cement boards using pearlite with excellent physical adsorption performance due to micropores in materials, expanded graphite that is widely used as a flame retardant to prevent heat transfer in the event of a fire. The experimental items are bending fracture load and impact resistance. The bending destruction load at the fiber mixing rates 1, 2, 3, and 4 (%) did not meet the standard 140N, but the bending destruction load at 5% was 168.2N, and the impact resistance of the fiber mixing rates 1 and 2 (%) could not be measured due to cracks and damage, and the impact resistance at 3, 4, and 5 (%).