• 한국강구조학회 논문집
• /
• 제21권3호
• /
• pp.257-266
• /
• 2009

다이아그리드 노드의 지진 및 바람에 의한 반복하중에 대한 구조성능을 해석적으로 평가하는 것은 용접특성의 반영이 어려워서 한계가 있다. 이 연구에서는 횡하중을 받는 다이아그리드 노드의 구조거동을 알아보기 위해 다이아그리드의 노드부를 축소한 모형을 이용해 실험을 수행했다. 실험체는 총 5개이며 실험의 변수는 각 부분의 용접방법, 측면스티프너와 가새 웨브의 겹침길이이다. 한쪽 대각가새에는 인장력을, 다른쪽 대각가새에는 압축력을 가하는 반복가력 실험을 수행하였다. 실험 결과 주요 파괴 원인은 축력과, 방향이 상이한 두 힘의 합력으로 인한 부가적 모멘트에 의한 작용으로 나타났다. 인장력에 의해서 가새 부재의 플랜지가 파단하였고, 압축력에 의해서 가새 플랜지의 국부좌굴이 일어났다. 또한 겹침길이와 용접타입은 초기 강성, 항복 내력 및 에너지 흡수능력에 영향을 미치는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.9-14
• /
• 2017

This paper presents a rotordynamic analysis and the operation of a power turbine applied to a 250 kW super-critical $CO_2$ cycle. The power turbine consists of a turbine wheel and a shaft supported by two fluid film bearings. We use a tilting pad bearing for the power turbine owing to the high speed operation, and employ copper backing pads to improve the thermal management of the bearing. We conduct a rotordynamic analysis based on the design parameters of the power turbine. The dynamic coefficients of the tilting pad bearings were calculated based on the iso-thermal lubrication theory and turbine wheel was modeled as equivalent inertia. The predicted Cambell diagram showed that there are two critical speeds, namely the conical and bending critical speeds under the rated speed. However, the unbalance response prediction showed that vibration levels are controlled within 10 mm for all speed ranges owing to the high damping ratio of the modes. Additionally, the predicted logarithmic decrement indicates that there is no unstable mode. The power turbine uses compressed air at a temperature of $250^{\circ}C$ in its operation, and we monitor the shaft vibration and temperature of the lubricant during the test. In the steady state, we record a temperature rise of $40^{\circ}C$ between the inlet and outlet lubricant and the measured shaft vibration shows good agreement with the prediction.

• 대한기계학회논문집A
• /
• 제38권4호
• /
• pp.401-407
• /
• 2014

본 논문에서는 3점 굽힘과 이중 외팔보 문제에 대하여 응집 요소를 사용한 유한요소 균열 진전해석을 수행하고 응집 법칙의 영향을 알아보았다. 응집 요소는 ABAQUS/Standard의 사용자 서브루틴(UEL)으로 구현하였으며 응집 법칙은 다항식 형태의 응집 트랙션-열림 변위의 관계식을 사용하였고 응집 법칙의 형상에 대한 영향을 알아 보기 위하여 다항식의 계수를 변화시켰다. 동일한 파손 에너지와 응집 강도를 갖지만 다른 형상의 응집 법칙에 대한 해석을 수행하고 변위-반력 곡선을 비교하여 균열 진전 거동의 변화를 알아보았다. 또한 요소 크기에 따른 균열 진전 해석 결과의 영향을 논의하였다.

• 수산해양기술연구
• /
• 제21권2호
• /
• pp.142-150
• /
• 1985

1. 반구형 각의 분포 및 집중하중에 의한 좌굴응력 해석은 변형된 각의 형상에 따라 타원체 각의 응력으로 해석함이 타당하다. 2. 일정 한계이상의 형상계수를 갖는 반 구형각에 대하여서는 재료상수를 형상계수의 승수로 고려한 수정된 임계좌굴 하중으로 탄소성 좌굴을 판정함이 더 양호한 결을 준다. 3. 탄소성 좌굴에 있어서 소모된 소성변형 에너지를 계산하기 위하여 항성변형 에너지를 계산하기 위하여 항상선를 따르는 에너지법을 이용하면 양호한 결과를 얻을 수 있다.

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.297-303
• /
• 1998

The effect of aliovalent dopants, $ Nb_2O_5$ and MnO, on the phase stability of 12 mol% ceria partially-stabilized zirconia (Ce-TZP) polycrystals was studied. Both dopants (MnO and $ Nb_2O_5$) significantly increased the stability of the tetragonal zirconia phase (Mb temperature lower than liquid nitrogen temperature). The enhancement of the stability of the tetragonal phase in Ce-TZP doped with 1 mol% of Mno(Ce-TZP/MnO) andCe-TZP doped with 1 mol% of $ Nb_2O_5$(Ce-TZP/$ Nb_2O_5$) were explained by the significant reduction of the driving force, -${\Delta}$Gchem, for the tetragonal-to-mono-clinic phase transformation caused by the addition of MnO and $ Nb_2O_5$. The enhanced stability of the tetragonal phase in the Ce-TZP and Al2O3 composite (Ce-TZP/$Al_2O_3$) is believed to be caused by smaller grain size, moderate reduction in the chemical driving force and increase in the strain energy barrier to the transformation. Mechanical properties of the Ce-TZP and the Ce-TZP/$Al_2O_3$ with (i) the same grain size and (ii) the same Mb temperature were examined by measuring stress-strain behavior in 3 point bending. The Ce-TZP/$Al_2O_3$ composite doped with 1.3w% MnO (Ce-TZP/$Al_2O_3$/MnO), which had the same grain size as the Ce-TZP and De-TZP/$Al_2O_3$ showed more transformation plasticity than either the Ce-TZP or the Ce-TZP/$Al_2O_3$ composite. The Ce-TZP wihch had the same Mb temperature as that of the Ce-TZP/$Al_2O_3$/MnO did not show any transformation plasticity.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.446-446
• /
• 2011

One dimensional (1-D) structures of ZnO nanorods are promising elements for future optoelectronic devices. However there are still many obstacles in fabricating high-quality p-type ZnO up to now. In addition, it is limited to measure the degree of the doping concentration and carrier transport of the doped 1-D ZnO with conventional methods such as Hall measurement. Here we demonstrate the measurement of the electronic properties of p- and n-doped ZnO nanorods by the Kelvin probe force microscopy (KPFM). Vertically aligned ZnO nanorods with intrinsic n-doped, As-doped p-type, and p-n junction were grown by vapor phase epitaxy (VPE). Individual nanowires were then transferred onto Au films deposited on Si substrates. The morphology and surface potentials were measured simultaneously by the KPFM. The work function of the individual nanorods was estimated by comparing with that of gold film as a reference, and the doping concentration of each ZnO nanorods was deduced. Our KPFM results show that the average work function difference between the p-type and n-type regions of p-n junction ZnO nanorod is about ~85meV. This value is in good agreement with the difference in the work function between As-doped p- and n-type ZnO nanorods (96meV) measured with the same conditions. This value is smaller than the expected values estimated from the energy band diagram. However it is explained in terms of surface state and surface band bending.

• 한국생활과학회지
• /
• 제16권5호
• /
• pp.979-986
• /
• 2007

The purpose of this study is to investigate the dyeability, and the hand of soybean/cotton blended fabric after dyeing with natural and synthetic dyes. Soybean/cotton blended fabrics dyed with extracted solution from turmeric, sappan wood, gardenia and synthetic dyes(weak-acid dyes, reactive dyes, direct dyes). The hand value of soybean/cotton blended fabrics dyed with 6 different dyes was measured using Kawabata Evaluation System. The results are as follows; 1. The K/S value of the soybean/cotton blended fabric dyed with sappan wood extracts was the highest. 2. The color fastness of the soybean/cotton blended fabric dyed with reactive dyes was excellent. The fastness to the light of the same fabric was much better than the other fabrics. 3. Linearity of load-extension and tensile energy of the soybean/cotton blended fabric dyed with sappan wood extracts showed very high. Shear stiffness of the soybean/cotton blended fabric dyed with weak-acid dyes was much higher than that of fabric of dyed with reactive dyes. Bending property of the fabrics dyed with natural colorants(sappan wood, gardenia) showed very high, but that the fabric dyed with reactive dyes was very poor. 4. In the primary hand value, stiffness and anti-drape stiffness of the fabric dyed with weak-acid dyes showed the highest. Fullness and softness of the fabric dyed with weak-acid dyes showed very low.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.266-270
• /
• 2004

SiC materials have been extensively studied for high temperature components in advanced energy system and advanced gas turbine because it has excellent high temperature strength, low coefficient of thermal expansion, good resistance to oxidation and good thermal and chemical stability etc. However, the brittle characteristics of SiC such as low fracture toughness and low strain-to fracture still impose a severe limitation on practical applications of SiC materials. For these reasons, SiC/SiC composites can be considered as a promising for various structural materials, because of their good fracture toughness compared with monolithic SiC ceramics. But, high temperature and pressure lead to the degradation of the reinforcing jiber during the hot pressing. Therefore, reduction of sintering temperature and pressure is key requirements for the fabrication of SiC/SiC composites by hot pressing method. In the present work, monolithic Liquid Phase Sintered SiC (LPS-SiC) was fabricated by hot pressing method in Ar atmosphere at $1800^{\circ}C$ under 20MPa using $Al_2O_3,\;Y_2O_3\;and\;SiO_2$ as sintering additives in order to low sintering temperature and sintering pressure. The starting powder was high purity $\beta-SiC$ nano-powder with all average particle size of 30mm. The characterization of LPS-SiC was investigated by means of SEM and three point bending test. Base on the composition of sintering additives-, microstructure- and mechanical property correlation, tire compositions of sintering additives are discussed.

• Structural Engineering and Mechanics
• /
• 제59권2호
• /
• pp.261-275
• /
• 2016

Effect of silica fume on fresh properties, compressive strength at 28 days and fracture behavior of fly ash concrete composite were studied in this paper. Test results indicated that the fluidity and flowability of fly ash concrete composites decreased and fly ash concrete composite are more cohesive and appear to be sticky with the addition of silica fume. Addition of silica fume was very effective in improving the compressive strength at 28 days of fly ash concrete composite, and the compressive strength of fly ash concrete composite has a trend of increase with the increase of silica fume content. Results also indicated that all the fracture parameters of effective crack length, fracture toughness, fracture energy, the critical crack opening displacement and the maximum crack opening displacement of fly ash concrete composite decreased with the addition of silica fume. When the content of silica fume increased from 3% to 12%, these fracture parameters decreased gradually with the increase of silica fume content. Furthermore, silica fume had great effect on the relational curves of the three-point bending beam specimen. As the silica fume content increased from 3% to 12%, the areas surrounded by the three relational curves and the axes were becoming smaller and smaller, which indicated that the capability of concrete composite containing fly ash to resist crack propagation was becoming weaker and weaker.

• 콘크리트학회논문집
• /
• 제13권2호
• /
• pp.161-167
• /
• 2001

RILEM위원회가 제시한 3점 휨 시험은 하중-변위곡선 형상이 불규칙하고 안정된 균열 발생 후 최종 균열이 발생하기 때문에 정확한 파괴인성을 구하는 것은 어렵다. 그러나 디스크 시험은 균열개시하중만 알면 쉽게 파괴인성을 구할 수 있다. 따라서, RILEM위원회가 제시한 3점 휨 시험보다 파괴인성 계산의 편리함을 보이기 위해 중앙에 노치가 있는 고강도 콘크리트 디스크를 실험하여 실험결과와 유한요소해석에 의한 결과를 비교하였다. 또한 실험에 의한 파괴 포락선과 이론에 의한 파괴 포락선도 비교하였으며, 콘크리트 강도수준에 따른 파괴특성의 차이를 나타내었다. 본 연구의 결과는 다음과 같다 유한요소해석과 실험결과를 비교해 볼 때, 최대 원주방향 인장응력 이론을 적용한 유한요소해석은 실험결과와 좋은 일치를 보였다. 그리고 콘크리트의 강도수준에 따른 파괴특성의 차이는 균열개시하중과 파괴인성 등에 영향을 끼치지만 최종 균열전파각의 변화에는 큰 영향이 없었다. 또한, 최대 원주방향 인장응력이론에 의한 파괴 포락선과 실험에 의한 포락선이 일치하지 않는 이유는 콘크리트에서 혼합모드와 면내전단모드(모드 II) 파괴를 유발하는 데 필요한 에너지량이 크기 때문이라고 판단된다