• 한국항해항만학회지
• /
• 제31권3호
• /
• pp.271-279
• /
• 2007

선체구조는 기본적으로 판부재의 조합으로 이루어져 있으며, 이러한 판부재의 하중분담 능력 혹은 최종강도 평가는 선체구조의 합리적인 설계 및 구조의 안정성 평가에 있어서는 아주 중요하다. 또한, 선체구조를 구성하고 있는 구조요소들은 작용외력에 대하여 개별적으로 작용하지 않으며 전체적으로 연속거동을 하게 된다. 실제 선박에서의 붕괴형태 중 한가지는 종방향 굽휨에 의해서 갑판 혹은 선저부에 좌굴 및 소성붕괴이다. 그래서, 합리적인 설계에서는 이러한 급작스런 붕괴형태를 방지하기 위하여 좌굴 및 소성붕괴 거동을 파악하는 것이 아주 중요하며, 실제 선박에서는 갑판부와 선저부에서는 하중분담 능력을 증가시키기 위하여 여러개의 종보강재를 가진 보강판 구조의 설계를 하게 된다. 본 연구에서는 선체 판넬구조의 모델링 방법에 따른 최종강도 거동의 차이를 분석하여, 합리적인 모델링영역을 규명하고자 한다. 사용된 해석 모델은 실제 상선의 이중저구조에서 사용되는 판넬에서 채택하였으며 유한요소해석 모델링 시 3가지 단면형상에 대해 각각 6가지 서로 다른 해석모델을 적용하였으며, 이때 보강재의 단면형상을 변화하였다. 본 연구의 목적은 압축하중이 작용하는 선체 보강판구조에서 해석영역에 대한 좌굴 및 최종강도 거동의 특성을 분석하였다.

• 한국농공학회지
• /
• 제43권6호
• /
• pp.113-119
• /
• 2001

Experiments on the yield strength of pipe connectors made of metal wire, joint pins, pole pipes, multi span insertion joints, and T-clamp joints used in pipe houses were conducted. The strength of connections of a pipe connector made of metal wire was adequate but it had a big difference according to loading direction. Therefore as it is installed, its direction should be taken into consideration. The collapse load of pipes connected with a joint pin was lower than that of single pipes. In the part of frame member at which the great bending moment occurs, the use of joint pin should be avoided. Also experimental results showed that pole pipes for use in a part of frame buried under the ground were safe, and the strength of multi span insertion joints should be increased. The resistant moment of T-clamp was about 13.7% of a single pipe. In case that the external forces acting on left and right rafter are different. a unsymmetrical rotational force is produced at the multi span joint. If it is expected that the actual bending moment on the multi span joint is larger than resistant moment of T-clamp, a reinforcement to safely resist the rotational force is required.

• 한국해양공학회지
• /
• 제22권2호
• /
• pp.85-90
• /
• 2008

Ships in bad weather conditions are likely to be subjected to accidental loads, such as high bending moment, collision, and grounding. Once she has damage to her hull, her ultimate strength will be reduced. This paper discusses an investigation of the effect of collision damage on the ultimate strength of a ship structure by performing a series of collapse tests. For the experiment, five box-girder models with stiffeners were prepared with a cross section of $720mm\;{\times}\;720mm$ and a length of 900mm. Of the five, one had no damage and four had an ellipse shaped damage area that represented the shape of the bulbous bow of a colliding ship. The amount of damage size was different between models. Among the damaged models, the damage in three of them was made by cutting the plate and stiffener, and in one by pressing to represent collision damage. Experiments were carried out under a pure bending load and the applied load and displacements were recorded. The ultimate strength was reduced as the damage size increased, as expected. The one with the largest amount of damage had damage to 30% of the depth, and its ultimate strength was reduced by 19% compared to the undamaged one. The pressed one has higher ultimate strength than those that were cut. This might be due to the fact that the plate around the pressed damage area contributes to the ultimate strength, whereas the cut one has no plate to contribute.

• 대한토목학회논문집
• /
• 제29권2A호
• /
• pp.109-118
• /
• 2009

이 연구에서는 CFT부재를 거더로 사용하는 신형식 강합성 교량 시스템 개발을 최종목표로 하고, CFT부재의 휨거동 특성을 규명하기 위한 부재실험을 수행하였다. 실험체는 충전재 강도 및 합성조건 변화 등 설계에 영향을 미치는 주요 매개변수를 고려하여 제작하였고, 휨재하 실험의 결과분석을 통해 CFT부재가 갖는 내력성능을 효율적으로 설계에 반영하기 위한 방안을 고찰하였다. 충전강관은 중공강관에 비해 휨강도 및 연성이 크게 증가함을 확인할 수 있었으며, 콘크리트의 취성적 재료 특성이 강관의 구속효과로 보완되는 결과를 확인하였다. 내부 전단연결재를 둠으로써 충전재와 강관 사이의 미끄러짐을 억제하여 완전합성단면으로 거동하였고, ㄱ형 전단연결재의 보강재 효과가 휨내력 증가에 다소 기여하고 있음을 알 수 있었다.

• Structural Engineering and Mechanics
• /
• 제14권4호
• /
• pp.473-489
• /
• 2002

A static linear programming formulation for minimum weight design of frames that is based on a matrix displacement method is presented in this paper. According to elementary theory of plasticity, minimum weight design of frames can be carried out by using only the equilibrium equations, because the system is statically determinate when at an incipient collapse state. In the present formulation, a statically determinate released frame is defined by introducing hinges into the real frame and the bending moments in yield constraints are expressed in terms of unit hinge rotations and the external loads respectively, by utilizing the matrix displacement method. Conventional Simplex algorithm with some modifications is utilized for the solution of linear programming problem. As the formulation is based on matrix displacement method, it may be easily adopted to the weight optimization of frames with displacement and deformation limitations. Four illustrative examples are also given for comparing the results to those obtained in previous studies.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.173-178
• /
• 2002

Flat plate is susceptible to punching shear failure at the slab-column connection, which may cause catastrophic structural collapse. To prevent such brittle failure, strength and ductility of the connection should be ensured. However, since it is very difficult to experimentally simulate the actual load and boundary conditions of the flat plate system, it is not easy to obtain reliable information and data regarding to the strength and ductility of the flat plate-column edge connection. In the present study, numerical studies were performed for edge connections of continuous flat plate. The results were compared with the existing experiments, and the variations of bending moment, drift, effective width around the connection were investigated. Based on tile findings of the numerical studies, the disadvantages of current design methods were discussed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.891-896
• /
• 2002

Flat plate is susceptible to punching shear failure at the slab-column connection, which may cause catastrophic structural collapse. To prevent such brittle failure, strength and ductility of the connection should be ensured. However, since it is very difficult to experimentally simulate the actual load and boundary conditions of the flat plate system, it is not easy to obtain reliable information and data regarding to the strength and ductility of the flat plate-column connection. In the present study, numerical studies were performed for interior connections of continuous flat plate. The results were compared with the existing experiments, and the variations of bending moment, shear, torsional moment around the connection were investigated. Based on the findings of the numerical studies, the disadvantages of current design methods were discussed.

• Structural Engineering and Mechanics
• /
• 제8권4호
• /
• pp.325-341
• /
• 1999

A procedure for the computation of the load carrying capacity of perfectly plastic plates in bending is presented. The approach, based on the kinematic theorem of limit analysis, requires the evaluation of the minimum of a convex, but non-smooth, function under linear equality constraints. A systematic solution procedure is devised, which detects and eliminates the finite elements which are predicted as rigid in the collapse mechanism, thus reducing the problem to the search for the minimum of a smooth and essentially unconstrained function of nodal velocities. Both Kirchhoff and Mindlin plate models are considered. The effectiveness of the approach is illustrated by means of some examples.

• Structural Engineering and Mechanics
• /
• 제51권6호
• /
• pp.1017-1036
• /
• 2014

Steel tubes have an efficient shape with large second moment of inertia relative to their light weight. One of the main problems of these members is their low buckling resistance caused from having thin walls. In this study, steel foams with high strength over weight ratio is used to fill the steel tube to beneficially modify the response of steel tubes. The linear eigenvalue and plastic collapse FE analysis is done on steel foam filled tube under pure compression and three point bending simulation. It is shown that steel foam improves the maximum strength and the ability of energy absorption of the steel tubes significantly. Different configurations with different volume of steel foam and composite behavior is investigated. It is demonstrated that there are some optimum configurations with more efficient behavior. If composite action between steel foam and steel increases, the strength of the element will improve, in a way that, the failure mode change from local buckling to yielding.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.166-169
• /
• 2006

A new bridge system described in this paper uses concrete-filled steel tube (CFT) girders as a replacement for conventional girders. Experimental investigations were carried out to comprehend the flexural behavior of CFT girder-slab deck composite section. The experimental investigation consisted of designing and constructing a test specimen and loading it to collapse in bending to check the applicability of the system. The test results showed that concrete filled steel tube girders have good ductility and maintain its strength up to the end of the loading. In the test, the flexural behavior of each specimen of CFT girder-deck composite section is identified.