• 한국인터넷방송통신학회논문지
• /
• 제16권1호
• /
• pp.233-238
• /
• 2016

근래에 임베디드 프로세서의 성능을 향상시키기 위하여 멀티코어 프로세서 구조가 널리 이용되고 있다. 이러한 멀티코어 프로세서는 크게 대칭적 구조와 비대칭적 구조로 나뉘며, 비대칭적 멀티코어 프로세서가 대칭적 멀티코어 프로세서에 비하여 더욱 성능이 높고 효율적이라고 알려져 있다. 본 논문에서는 임베디드 프로세서에 대하여 이것을 확인하기 위하여, 다양한 구성을 갖는 비대칭적 임베디드 듀얼코어, 쿼드코어, 옥타코어 및 헥사데카코어 프로세서에 대하여 MiBench 벤치마크를 입력으로 하여 모의실험을 수행하여 그 성능을 측정하였다. 또한, 비슷한 하드웨어 규모의 대칭적 임베디드 멀티코어 프로세서와 비교하여 성능의 우수성을 확인하였다.

• 항공우주기술
• /
• 제11권1호
• /
• pp.185-191
• /
• 2012

본 논문에서는 축소 로터의 성능시험과 축소 헬기 Flight Test Bed 개발이 가능한 헬리콥터 섀시다이나모미터(HCDS)를 개발하여 지상시험을 수행하였다. 축소 헬기는 엔진 출력에 따른 컬렉티브 피치각의 상호 관계로부터 로터의 일정 회전속도에 대한 추력과 동력의 변화를 확인하고, 그 결과로 OGE에서의 정지비행효율(F.M.)이 0.76으로 비행시험 가능성을 점검하였다. 본 헬리콥터 섀시다이나모미터(HCDS) 시험 결과는 축소 헬기 개발과 로터 블레이드의 성능 평가에 활용할 것이다.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1373-1383
• /
• 2001

The desulfurization characteristics of anthracite in a bench scale pressurized fluidized bed combustor are investigated. The coal used in the experiment is domestic anthracite from Kangwon Taeback area. The desulphurization experiment is performed with limestone from Chungbuk Danyang. The pressure of the combustor is maintained at 6 atm, and the combustion temperatures are 850, 900, and 950$\^{C}$. The superficial gas velocities are 0.9, 1.1, and 1.3 m/s. The excess air ratio is varied from 5 to 35%. The Ca/S mole ratios are 0.5, 1.5, 2.5 and 4.5 mole. All experiments are executed at 2m bed height. Consequently, SO$_2$ concentration in the flue gas is increased with incresing bed temperature and superficial gas velocity. However SO$_2$ concentration is decreased with incresing excess air ratio and Ca/S mole ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.709-714
• /
• 2000

A splitting method for the direct numerical simulation of solid-liquid mixtures is presented, where a symmetric pressure equation is newly proposed. Through numerical experiment, it is found that the newly proposed splitting method works well with a matrix-free formulation fer some bench mark problems avoiding an erroneous pressure field which appears when using the conventional pressure equation of a splitting method. When deriving a typical pressure equation of a splitting method, the motion of a solid particle has to be approximated by the 'intermediate velocity' instead of treating it as unknowns since it is necessary as a boundary condition. Therefore, the motion of a solid particle is treated in such an explicit way that a particle moves by the known form drag (pressure drag) that is calculated from the pressure equation in the previous step. From the numerical experiment, it was shown that this method gives an erroneous pressure field even for the very small time step size as a particle velocity increases. In this paper, coupling the unknowns of particle velocities in the pressure equation is proposed, where the resulting matrix is reduced to the symmetric one by applying the projector of the combined formulation. It has been tested over some bench mark problems and gives reasonable pressure fields.

• 한국측량학회지
• /
• 제13권2호
• /
• pp.237-244
• /
• 1995

본 연구에서는 수준점에 대한 GPS 관측결과로부터 WGS84 지오이드고 모델을 구성하고 Bi-linear방법, 회귀다항식 방법 및 삼각보간법을 사용하여 check points로 선정한 수준점에 대한 지오이드고를 산출하므로써 보간방법에 따른 보간정확도를 비교, 분석하였다. 또한 삼각점의 GPS 관측성과로부터 도출한 좌표변환계수를 적용하여 수준점의 Bessel 경 위도좌표를 구하고 수준점의 표고성과와 조합하여 수준점의 표고변환의 정확도를 검토하였다. 그 결과, 수준점의 WGS84지오이드고 및 정표고를 평균 20 cm의 편차로 결정할 수 있었다.

• 대한물리의학회지
• /
• 제10권3호
• /
• pp.81-86
• /
• 2015

PURPOSE: Bridge exercises are broadly used to develop trunk co-activation patterns that promote spine stability. This study was to analyze the trunk muscle activity during bridge exercise with various shoulder support surface(stable, sling, Swiss ball). METHODS: The subjects were 20 healthy subjects in their twenties. Subjects were performed bridge exercise on 4 different shoulder support surfaces using stable and labile instruments. 1) Bridge exercise on a stable surface. 2) Bridge exercise with their shoulder on a stable bench. 3) Bridge exercise with their shoulder on a sling. 4) Bridge exercise with their shoulder on a Swiss ball. Rectus abdominis, erector spinae, internal oblique, external oblique muscle activities were measured using electromyography. RESULTS: There were significant differences in RA, EO muscles between performing each of the 4 exercises(p<.05). RA and EO was recorded the highest activity during the bridge exercise with their shoulder on a sling. The lowest activity was recorded during conventional supine bridge on a stable surface. There were no differences found for the EO/RA and IO/RA ratio. The EO/RA and IO/RA ratio was the highest in the bridge exercise with their shoulders resting on a stable bench. CONCLUSION: These findings suggest that change of shoulder support surface during bridge exercise may be useful for enhancing the trunk stability.

• 한국항공운항학회지
• /
• 제16권2호
• /
• pp.1-11
• /
• 2008

Increasing demand for improved reliability and survivability of mission-critical systems is driving the development of health monitoring and Automated Contingency Management (ACM) systems. An ACM system is expected to adapt autonomously to fault conditions with the goal of still achieving mission objectives by allowing some degradation in system performance within permissible limits. ACM performance depends on supporting technologies like sensors and anomaly detection, diagnostic/prognostic and reasoning algorithms. This paper presents the development of a generic prototype test bench software framework for developing and validating ACM systems for advanced propulsion systems called the Propulsion ACM (PACM) Test Bench. The architecture has been implemented for a Monopropellant Propulsion System (MPS) to demonstrate the validity of the approach. A Simulink model of the MPS has been developed along with a fault injection module. It has been shown that the ACM system is capable of mitigating the failures by searching for an optimal strategy. Furthermore, the concepts of Validation and Verification (V&V) of such systems are introduced with relevant examples.

• 한국주조공학회지
• /
• 제23권5호
• /
• pp.235-243
• /
• 2003

The collapsibility of sodium silicate-bonded sands mixed with the L.D converter slag powder to form a hardener were investigated. Five to six percent sodium silicate on the basis of silica sand and 30-40% L.D converter slag powder on the basis of sodium silicate, were mixed and the compressive strength, surface stability index(SSI), bench time, retained strength of the standard sand specimens were measured. The properties were similar to those of general inorganic bonded self-setting molds. The compressive strength and surface stability index were increased and the retained strength and bench time were decreased with increased amount of the L.D converter slag powder. The retained strength of sodium silicate-bonded self-setting molds with the L.D converter slag powder were decreased than $CO_2$ sand molds. The collapsibility of sodium silicate-bonded self-setting molds with the L.D converter slag powder were superior in comparison with $CO_2$ sand molds. The L.D converter slag powder could be used as hardener and collapse agent for the sodium silicate-bonded self-setting molds.

• 멤브레인
• /
• 제12권3호
• /
• pp.151-157
• /
• 2002

본 연구는 하수를 공업용수로 재이용하기 위한 분리막 시스템 적용에 관한 연구이다. 정밀여과와 역삼투시스템으로 구성된 bench scale 실험장치를 이용하여 하수처리장 현장에서 실험을 수행한 결과, 정밀여과 시스템은 이온성분은 제거할 수 없었으나 SS를 70% 이상 처리할 수 있어 처리수는 직접냉각수로 재이용이 가능하였다. 그리고 역삼투 시스템은 SS는 물론 이온성분도 95% 이상 제거할 수 있어 처리수는 간접냉각수 및 제품세척수로 사용이 가능하였다. $100 m^3$/일 용량의 pilot Plant를 제작하기 위해서는 정밀여과 모듈은 20개, 역삼투 모듈은 12개가 필요하였다.

• 소성∙가공
• /
• 제13권3호
• /
• pp.211-215
• /
• 2004

Recently, one of remarkable tends in the development of optical communication industry is the miniaturization and integration of products. The alignment system of micro optical module is a key apparatus for the miniaturization of optical module and the development of optical communication parts with high functionality. In this research, we have developed a system capable of automatic alignment of a $30\mu\textrm{m}$-thick film filter and a lensed fiber in order to improve the speed and losses in the optical fiber-to-filter alignment of optical modules. Using the developed automatic alignment system and silicon optical bench, we have measured optical loss and characteristics of the assembled optical add/drop module before packaging $1{\times}1$ OADM optical module. Whole size of add/drop module was less than $5mm{\times}5mm{\times}1mm$. The measured maximum insertion loss was 0.294㏈ that is below 0.3㏈ which is a standard loss of optical module.