• 한국운동역학회지
• /
• 제16권4호
• /
• pp.189-194
• /
• 2006

The purpose of this study was to identify the relationship of one repetition maximum between flat bench press exercise and incline bench press exercise, and so 40 male students of U-university were sampled purposedly, who were skilled in flat bench press and incline bench press exercises. After measuring lRM of each exercise by free barbell weight, the correlation analysis and the simple regression analysis were examined by using SPSS 120 at a significance level .05. The conclusions were as follows; Firstly, it was identified that 1RM of flat bench press exercise and incline bench press exercise were $89.2{\pm}25.9kg$, $67.1{\pm}22.1kg$ respectively, and the coefficient of correlation between two variables was 0.969, so the relationship was positive correlation. Secondly, it was identified that the regression equation predicted 1RM of incline bench press exercise was significant actually and statistically, so it was expressed that the equation was -6.648 + 0.827 (1RM of flat bench press exercise).

• Geomechanics and Engineering
• /
• 제13권5호
• /
• pp.715-742
• /
• 2017

Earth berms are often left in place to support retaining walls or piles in order to eliminate horizontal struts in excavations of soft soil areas. However, if the excavation depth is relatively large, an earth berm-supported retaining system may not be applicable and could be replaced by a multi-bench retaining system. However, studies on multi-bench retaining systems are limited. The goal of this investigation is to study the deformation characteristics, internal forces and interaction mechanisms of the retaining structures in a multi-bench retaining system and the failure modes of this retaining system. Therefore, a series of model tests of a two-bench retaining system was designed and conducted, and corresponding finite difference simulations were developed to back-analyze the model tests and for further analysis. The tests and numerical results show that the distance between the two rows of retaining piles (bench width) and their embedded lengths can significantly influence the relative movement between the piles; this relative movement determines the horizontal stress distribution in the soil between the two rows of piles (i.e., the bench zone) and thus determines the bending moments in the retaining piles. As the bench width increases, the deformations and bending moments in the retaining piles decrease, while the excavation stability increases. If the second retaining piles are longer than a certain length, they will experience a larger bending moment than the first retaining piles and become the primary retaining structure. In addition, for varying bench widths, the slip surface formation differs, and the failure modes of two-bench retained excavations can be divided into three types: integrated failure, interactive failure and disconnected failure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.805-808
• /
• 2005

This paper is a study on an optical bench satisfying stiffness and thermal pointing error requirements for LEO earth observation satellite. According to shape and stiffness requirements, optical bench type 1 is designed. Because type 1 does not satisfy the thermal pointing error requirement, an optical bench type 2 is suggested. Although the type 2 has better results than type 1, it still does not meet the thermal pointing error requirement. Using the results of optical bench type 1&2, the optical bench type 3 is finally designed, which satisfies both the stiffness and thermal pointing error requirements.

• 한국분무공학회지
• /
• 제20권3호
• /
• pp.195-201
• /
• 2015

This study discusses a fuel injector test bench containing a mechanical type fuel supply system for heavy duty diesel engine. The main focus of this study was to evaluate the design stability of the test bench, which basically measures the injector durability of a multi-hole heavy duty injector by using pure diesel as a test fuel. In this experiment, diesel spray was controlled by a specially designed control box and all the experiments were carried out to measure e.g. fuel injection pressure and fuel injection quantity to understand the injection status which is interlinked with the stability factor of total test bench design. Also, the durability test was performed to understand the heavy duty operation lastingness of the designed system and the flow rate of the installed distributor pump in the fuel supply system of this studying test bench was compared with LO-1 and LO-2 pump. The results of the above mention tests revealed that the injector test bench design and control system can serve the purpose for heavy duty injector.

• 대한치과기공학회지
• /
• 제12권1호
• /
• pp.103-106
• /
• 1990

The purpose of this study was to determine if homogeneity of the resin associated with benchcuring could be obtained in the curing unit as the water increased from room temperature to curing temperature. The results of the experiment were as follows : 1. Long periods of bench-curing are not necessary. 2. Bench-curing can take place in the water bath of the curing unit. When this procedure is used, the water should be far enough below the temerature at which active polymerization of the resin proceeds to allow the bench-curing to occur.

• International Journal of Aerospace System Engineering
• /
• 제1권1호
• /
• pp.10-15
• /
• 2014

This study presents technical description of the operating program development that operates the test bench for functional test of EECU. The test bench is capable of testing, simulation and adjustment of the EECU software using the operating program. The test bench is for the Development Project of the EECU platform for FADEC system. The operating program is consists of 3 modules which are the test bench operating module, cockpit simulator module and SILS module. The operating module mainly carries out the EECU test with manual operation and operating scenarios. Also that record and process the test data. The cockpit simulator module is capable of implementation of virtual cockpit control input and engine status display. The SILS module can simulate engine and EECU operation in software environment.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.777-780
• /
• 2005

The bench of cut-slope is necessary to stabilizing. But it is possible to be a weak zone in slope. When a small scale failure is occurred in a bench, it influence a large scale failure of slope. So when it is found out any unstable factor, weathering of rock, a direction of joint in a bench, if the bench is reinforced suitably, the holly failure is prevented in cut-slope

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.242-245
• /
• 2006

This paper is an assessment on the dynamic test results of optical bench for LEO satellite. According to the design requirements, optical bench was designed and manufactured. Dynamic test was performed to verify stability of optical bench. Low level random vibration test, sine burst test and sine vibration test are carried out to identify dynamic characteristics and to verify static strength and safety under quasi-static load conditions. From the result it can be stated that the optical bench is well qualified under the launch environmental conditions.

• 대한조선학회논문집
• /
• 제52권6호
• /
• pp.452-459
• /
• 2015

It is important to use bench test results in the design process of anti-rolling tanks. Traditional bench tester is usually designed to perform only roll motions about a fixed axis and relatively small so that the viscous effects may not be neglected. Novel bench tester which could adjust the motion center to realize the coupled motion of sway and roll has been devised and manufactured therefore, large scaled bench tester could be utilized for designing the passive anti-rolling tanks. The time history of the reference signal from the rotation sensor of the bench tester have been recorded and processed to determine the phase angle to derive the Response Amplitude Operator(RAO) of the stabilized ship. The breadth of ART tank model should be large up to 2 m to diminish viscous scale effect and the vertical position of the tank can be varied with the ship's center of motion. The periods and the amplitude of roll motion can be varied from 1.5 sec to 5 sec and up to ±20°, respectively. The components of the tester was expressed in three dimensional digital mockup (DMU) and assembled together in the CAD space. The final configuration of the bench tester has been determined by confirming the smooth operation of the moving parts without interference through the animation in CAD space. New analytic logic are introduced for the determination of hydrodynamic moment and phase difference due to fluid motion in ART and verified through the test. The developed bench tester is believed to be effective and accurate for the verification of stabilization effect of ART taking into the consideration of the sway effect in the design stage.

• 터널과지하공간
• /
• 제11권1호
• /
• pp.30-35
• /
• 2001

본 연구에서는 전단면굴착에 가까운 작업 사이클(cycle)로 굴진을 하면서 분할효과를 거두기 위해 적절한 벤치길이를 결정하는 것이 중요한 요소로 판단하여 전단면, 미니벤치, 숏벤치로 풍화암 구간에 굴착한 터널을 모델링하여 이에 대해 3차원 탄소성해석을 수행하였다. 그리고 터널내 암반과 지보재의 거동에 영향을 미치는 주요 요소로 무지보 굴착구간의 길이, 측압계수, 숏크리트 두께 등의 설계변수를 변화시켜가며 암반의 변형거동을 분석하였다. 해석결과 내공변위는 숏벤치보다 미니벤치일때 벤치길이에 민감하게 반응하는 것으로 나타났으며 무지보길이가 길 때 하반굴착이 상반변위에 미치는 영향이 더 크게 나타나며 상반과하반측벽에서의 변위타이가증가하였다 K값의 증가에 따라 천정, 바닥보다 상하반 측벽부에서 변위와 선행변위비의 증가가 훨씬 크게 나타났다.