• Journal of Welding and Joining
• /
• v.28 no.2
• /
• pp.74-78
• /
• 2010

In this paper, a non-contact method of evaluating the thickness reduction in an aluminum sheet caused by corrosion and friction using SH-EMAT (shear horizontal, electromagnetic acoustic transducer) is described. Since this method is based on the measurement of the time-of-flight and amplitude change of guided waves caused from the thickness reduction, it provides information on the thinning defects. Information was obtained on the changes of the various wave features, such as their time-of-flight and amplitude, and their correlations with the thickness reduction were investigated. The interesting features in the dispersive behavior of selected guided modes were used for the detection of thinning defects. The measurements of these features using SH waves were performed on aluminum specimens with regions thinned by 7.2% to 29.5% of the total thickness. It is shown that the time-of-flight measurement provides an estimation of the thickness reduction and length of the thinning defects.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.4
• /
• pp.973-988
• /
• 2012

Delay tolerant networks (DTNs) characterized by the lack of guaranteed end-to-end paths exploit opportunistic data forwarding mechanism, which depends on the hypothesis that nodes are willing to store, carry, and forward the in-transit messages in an opportunistic way. However, this hypothesis might easily be violated by the presence of selfish nodes constrained with energy, bandwidth, and processing power. To address this problem, we propose a practical reputation-based incentive scheme, named PRI, to stimulate honest forwarding and discipline selfish behavior. A novel concept of successful forwarding credential and an observation protocol are presented to cope with the detection of nodes' behavior, and a reputation model is proposed to determine egoistic individuals. The simulation results demonstrate the effectiveness and practicality of our proposal.

• Nuclear Engineering and Technology
• /
• v.47 no.3
• /
• pp.332-339
• /
• 2015

The leak before break (LBB) concept is widely used in designing pipe lines in nuclear power plants. According to the concept, the amount of leaking liquid from a pipe should be more than the minimum detectable leak rate of a leak detection system before catastrophic failure occurs. Therefore, accurate estimation of the leak rate is important to evaluate the validity of the LBB concept in pipe line design. In this paper, a program was developed to estimate the leak rate through circumferential cracks in pipes in nuclear power plants using the Henry-Fauske flow model and modified Henry-Fauske flow model. By using the developed program, the leak rate was calculated for a circumferential crack in a sample pipe, and the effect of the flow model on the leak rate was examined. Treating the crack morphology parameters as random variables, the statistical behavior of the leak rate was also examined. As a result, it was found that the crack morphology parameters have a strong effect on the leak rate and the statistical behavior of the leak rate can be simulated using normally distributed crack morphology parameters.

• Journal of the Korean Society for Railway
• /
• v.14 no.5
• /
• pp.398-403
• /
• 2011

When a crack exists under a residual stress, for example in welds, the crack can be closed and it shows non symmetric behavior for tension and compression. Ultrasonic detection method for those nonlinear cracks has been developed recently. The method uses the higher order harmonics generating at the crack surface. In this study, parameter study was carried out for the analysis of the harmonics generation at a nonlinear contact interface as a preliminary study for general 3-dimensional cracks. One-dimensional problem with simple bilinear behavior for the contacting surface was considered. The amplitude of second harmonic to the fundamental wave was obtained for various stiffness ratios, incident frequencies, and the contacting layer thicknesses.

• Smart Structures and Systems
• /
• v.15 no.3
• /
• pp.523-541
• /
• 2015

Structural health monitoring of steel truss bridge based on changes in modal properties was investigated in this study. Vibration measurements with five sensors were conducted at an existing Warren truss bridge with partial fractures in diagonal members before and after an emergency repair work. Modal properties identified by the Eigensystem Realization Algorithm showed evidences of increases in modal damping due to the damage in diagonal member. In order to understand the dynamic behavior of the bridge and possible mechanism of those increases in modal damping, theoretical modal analysis was conducted with three dimensional frame models. It was found that vibrations of the main truss could be coupled internally with local vibrations of diagonal members and the degree of coupling could change with structural changes in diagonal members. Additional vibration measurements with fifteen sensors were then conducted so as to understand the consistency of those theoretical findings with the actual dynamic behavior. Modal properties experimentally identified showed that the damping change caused by the damage in diagonal member described above could have occurred in a diagonal-coupled mode. The results in this study imply that damages in diagonal members could be detected from changes in modal damping of diagonal-coupled modes.

• Smart Structures and Systems
• /
• v.22 no.4
• /
• pp.399-411
• /
• 2018

The difficulty in modeling complex nonlinear structures lies in the presence of significant sources of uncertainties mainly attributed to sudden changes in the structure's behavior caused by regular aging factors or extreme events. Quantifying these uncertainties and accurately representing them within the complex mathematical framework of Structural Health Monitoring (SHM) are significantly essential for system identification and damage detection purposes. This study highlights the importance of uncertainty quantification in SHM frameworks, and presents a comparative analysis between intrusive and non-intrusive techniques in quantifying uncertainties for SHM purposes through two different variations of the Kalman Filter (KF) method, the Ensemble Kalman filter (EnKF) and the Polynomial Chaos Kalman Filter (PCKF). The comparative analysis is based on a numerical example that consists of a four degrees-of-freedom (DOF) system, comprising Bouc-Wen hysteretic behavior and subjected to El-Centro earthquake excitation. The comparison is based on the ability of each technique to quantify the different sources of uncertainty for SHM purposes and to accurately approximate the system state and parameters when compared to the true state with the least computational burden. While the results show that both filters are able to locate the damage in space and time and to accurately estimate the system responses and unknown parameters, the computational cost of PCKF is shown to be less than that of EnKF for a similar level of numerical accuracy.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.326-333
• /
• 2010

In this study, DAQ and TRA modules were applied to the CFRP single specimen testing method using AE. A method for crack identification in CFRP specimens based on k-mean clustering and wavelet transform analysis are presented. Mode I on DCB under vertical loading and mode II on 3-points ENF testing under share loading have been carried out, thereafter k-mean method for clustering AE data and wavelet transition method per amplitude have been applied to investigate characteristics of interfacial fracture in CFRP composite. It was found that the fracture mechanism of Carbon/Epoxy Composite to estimate of different type of fractures such as matrix(epoxy resin) cracking, delamination and fiber breakage same as AE amplitude distribution using a AE frequency analysis. In conclusion, the presented results provide a foundation for using wavelet analysis as efficient crack detection tool. The advantage of using wavelet analysis is that local features in a displacement response signal can be identified with a desired resolution, provided that the response signal to be analyzed picks up the perturbations caused by the presence of the crack.

• Journal of the Korea Society of Computer and Information
• /
• v.23 no.10
• /
• pp.65-72
• /
• 2018

In this paper, we used LSTM as a method to detect abnormal behavior of motors. We fixed the high layout size to 1 and changed the range of the input values and the neural network structure to see what change in power consumption prediction. Now, as the fourth industrial revolution era, smart factories are attracting attention. All the physical actions of smart factories are done using motors. Continuous monitoring of motor malfunctions helps to detect malfunctions and efficient operation. However, it is difficult to acquire the power consumption constantly due to the influence of the noise. We have experimented with a simple experimental environment, a method of predicting similarity to input data by adjusting the range of the input data or by changing the neural network structure.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.50 no.10
• /
• pp.479-485
• /
• 2001

In this paper, we introduce a charge pump phase-locked loop (PLL) architecture which employs a precharge phase frequency detector (PFD) and a sequential PFD to achieve a high frequency operation and a fast acquisition. Operation frequency is increased by using the precharge PFD when the phase difference is within $-{\pi}{\sim}{\pi}$ and acquisition time is shortened by using the sequential PFD and the increased charge pump current when the phase difference is larger than ${\pm}{\pi}$. So error detection range of the proposed PLL structure is not limited to $-{\pi}{\sim}{\pi}$ and a high frequency operation and a higher speed lock-up time can be achieved. The proposed PLL was designed using 1.5 ${\mu}m$ CMOS technology with 5V supply voltage to verify the lock in process. The proposed PLL shows successful acquisition for 200 MHz input frequency. On the other hand, the conventional PLL with the sequential PFD cannot operate at up to 160MHz. Moreover, the lock-up time is drastically reduced from 7.0 ${\mu}s\;to\;2.0\;{\mu}s$ only if the loop bandwidth to input frequency ratio is regulated by the divide-by-4 counter during the acquisition process. By virtue of this dual PFDs, the proposed PLL structure can improve the trade-off between acquisition behavior and locked behavior.

• KIPS Transactions on Software and Data Engineering
• /
• v.6 no.1
• /
• pp.29-36
• /
• 2017

In this paper, we propose a method for recognizing eating behavior with almost no motion acceleration. First, by using the acceleration of gravity acting on the wrist direction, we calculate the angle between the gravity and the wrist direction. After that, detect wrist reciprocating motion when peak and vally exist in specific angle band. And then, when accumulate the number of wrist reciprocating motion occurrences are up to 10, then regard as the meal time 5 minutes before the detection time. Also, estimate the meal time only if its duration is more than 7 minutes. Using the data of 2128 minutes, which was collected from four graduate student, the result of the meal time estimation shows 95.63% accuracy.