• Journal of Ginseng Research
• /
• v.7 no.2
• /
• pp.172-192
• /
• 1983

Light environment and growth of Panax ginseng In habitat and cultivation under natural shade were renewed. Grower's experiences on ginseng stand In relation to light environment were assessed. Change of shading method and grower's concepts on light requirement of ginseng plant in Korea, Manchuria and Japan was counted. Growth of wild ginseng was better under rich light. Optimum crown density index appeared to be 0.7 In natural habitat and 0.4 to 0.7 for the cultivation in forest. Change of light Intensity in forest was greatest in May and reached near to constant value (from 40% to 3% for broad leaf deciduous forest and loom 4% to 2% for pine forest). Insufficient light condition induced long and thin stem, poor flowering and seed bearing, and sequent dormancy. Relation between light and ginseng strand was not clear but light Interception with cool weather was effective. Topography and orientation of bed have been deeply considered for light environment. Panel or bark of won were used for shading in deep forest manly In Manchuria while reed blind and straw thatch were used in Korea. Kinds and number of shades material and seasonal or daily schedule have been simplified probably by labor pressure due to eulargement of plantation. Post height has been greater while width of roof, bed and ditch has changed lisle. Scientific survey in the past omitted important light control methods (complete light hardening etc) which has been practiced in specific areas. The concept and technique of light control in the past in Korea were delicate and intensive including the control of temperature and moisture. For the application of old concept in modem cultivation precise Investigation of the technique including the measurement of light, temperature and moisture is needed.

• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.680-684
• /
• 2008

The formation of methane hydrate ($CH_4$ hydrate) in silica sand and decomposition experiments were performed at $7.0^{\circ}C$ using a newly designed reactor. Temperature profile within silica sand bed was measured by thermocouples installed at different height of reactor. Both temperature and pressure are the main parameters for the formation (measured by adsorption experiment) and decomposition (measured by desorption experiment) of methane hydrate. Experiment of methane hydrate formation at 8 MPa and $7.0^{\circ}C$ showed that 70% of methane was converted to hydrate and the recovery of methane by the decomposition of methane hydrate was 82%.

• Environmental Engineering Research
• /
• v.11 no.1
• /
• pp.1-13
• /
• 2006

In this study, conventional biofilters packed with flexible synthetic polyurethane (PU) foam carriers were operated to remove toluene from a contaminated air stream. PU foams containing various adsorbents (e.g., zeolite, sepiolite, dolomite and barite) were synthesized for the biofilter media and their adsorption characteristics of toluene were determined. Adsorption capacity of PU-adsorbent foam was in the order of PU-dolomite ${\approx}$ PU-zeolite > PU-sepiolite > PU-barite. During the biofiltration experiment, influent toluene concentration was in the range of 0-160 ppm and EBRT (i.e., empty bed residence time) was 45 seconds. Pressure drop of the biofilter bed was 4-5 mm $H_2O/m$ column height. The maximum removal capacity was in the order of PU-dolomite > PU-zeolite > PU-sepiolite > PU-barite, while the complete removal capacity was in the order of PU-dolomite > PU-sepiolite > PU-zeolite > PU-barite. The better biofiltration performance in PU-dolomite foam was because PU-dolomite foam had lower density and higher porosity than the others providing favorable conditions for microbial growth. The results of biodegradation kinetic analysis showed that PU-dolomite foam had higher maximum removal rate ($V_m\;=\;11.04\;g$ toluene/kg dry material/day) and saturation constant ($K_s\;=\;26.57\;ppm$) than the other PU foams. This supports that PU-dolomite foam was better than the others for biofilteration of toluene.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.71.1-71.1
• /
• 2011

석석탄가스화 기술은 고온, 고압 조건에서 미분탄과 산소의 가스화 반응에 의해 CO와 $H_2$가 주성분인 합성가스를 제조하는 기술로서 차세대 화력발전 뿐만아니라 다양한 화학원료 제조를 위한 분야에서 각광을 받고 있다. 또한, 가스화 기술은 향후 CCS기술, CTL(Coal To Liquid, 석탄액화)기술, SNG(Synthetic Natural Gas, 합성천연가스)생산, 수소생산, 각종 화학원료 생산 등과 연계가 가능한 미래 석탄이용 분야의 핵심 기술이라 할 수 있다. 따라서, 고등기술연구원에서는 이러한 석탄가스화를 통해 양질의 합성가스를 제조하기 위한 기술 개발의 일환으로 pilot급 고온, 고압 건식 분류층 가스화기, 기류수송 방식의 미분탄공급장치, 수냉자켓 구조의 합성가스 냉각장치, 합성가스 중 분진제거를 위한 금속필터 장착 집진장치 등을 연계하여 20기압의 고압 조건에서 장시간 연속운전을 진행하였다. 본 연구에서는 미분탄 공급을 위하여 상부공급 버너를 적용하였고 석탄가스화기는 $1,300{\sim}1,350^{\circ}C$ 정도의 온도에서 운전을 진행하였으며 미분탄을 75 kg/h의 조건에서 연속적으로 공급하였다. 그리고, 이러한 조건에서 5.5일 정도의 연속운전을 진행하는 동안 CO 44~48%, $H_2$ 20~21%, $CO_2$ 4~5% 조성의 석탄 합성가스를 $200Nm^3/h$ 안정적으로 제조할 수 있었다.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.26 no.1
• /
• pp.73-84
• /
• 2020

Purpose: Though Korean healthcare services have been upgraded, infection and fire had been broken out in general hospitals. And higher concerns about quality assessment made it to clinical laboratory design guideline studies. So, this study investigates the facilities, equipment and personnel of laboratory medicine focusing on more than five hundred fifty bed hospital, and contributes to make guidelines for safety and efficiency in lab. Methods: Questionnaires to supervisor technologist and field surveys to medical laboratories in korean hospitals have been conducted for the data collection. 16 answers have been analysed statistically by MS Excel program. Results: Most of the sample tests such as hematology, clinical chemistry, immunology, transfusion, urinalysis, microbiology and molecular diagnosis are performed by more than 80% in large sized general hospital laboratory. In the test methods, automatic analyzers are used up to 80%, total laboratory automation up to 43% in clinical chemistry and immunology, and manual tests in all sorts of the test. There are placed in single lab or two and three labs above the ground, which are all in semi-open lab. There is some correlation with the number of specimens and the number of lab people depending on the number of hospital beds. Laboratory environment shows that work distance is good, but evacuation path width, visibility, separation of staff area from automatic analyzer, and equipment installations are needed to have more spaces and gears. Most of the infection controls are equipped with mechanical ventilation, air-conditioning, washbasin and wastewater separation, BSC installation and negative pressure lab room. Implications: Although the laboratory space area is calculated considering the number of hospital beds, type of tests and number of staff, hospital's expertise and the samples numbers per year should be taken into account in the planning of the hospital.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.2_1
• /
• pp.149-159
• /
• 2022

Biomass is material that is comprehensive of carbonaceous materials from plants, crops, animals, and algae. It has been used as one of heating fuel since the beginning the emergence of human beings. Since biomass is regarded as carbon-neutral energy source, it has recently been attracting attention as an energy source that can replace fossil fuels. The most widely applied field is distributed power generation, and a method of generating electric power by driving an internal combustion engine with syngas produced by gasifier is chosen. While the composition of the syngas produced in gasifiers changes depending on the air flowing into the reactor, commercialized gasifiers so far do not control the air flowing into the reactor. When the inner pressure in reactor increases, the air sucked into the reactor is reduced. That change of amount of air makes the composition of syngas varied. Those variations of composition of syngas cause the incomplete combustion hence the power output of engine drops, which is a critical weakness of the gasification technology. In this paper, to produce the uniformly composed syngas, PID control is applied. The result was shown when the amount of air into the reactor is supplied with the constant amount using PID control, the standard deviation of caloric values of syngas is around 2[%] of its average value. Meanwhile the gasifier without PID control has the standard deviation of caloric values is around 7[%]. Therefore, Adopting PID control to supply constant air to the gasifier is highly desirable.

• Clean Technology
• /
• v.17 no.1
• /
• pp.62-68
• /
• 2011

Hydrodynamic characteristics in multistage annular type fluidized bed (riser: $0.01{\times}0.025{\times}2.8m^3$, J-valve: $0.009{\times}0.015m^2$)were investigated. Glass beads ($d_p=101{\mu}m$, ${\rho}_b=1,590kg/m^3$, $U_{mf}=1.25{\times}10^{-2}m/s$, Geldart classification B) was used as a bed material. Accumulated weight by the electronic balance was measured to determine the solid flow rate in batch-type. In circulation condition, we measured the accumulated weight of particle transported from riser. At the steady state condition, solid circulation rate was calculated from time interval of the heated bed material passing between two thermocouples. Solid flow rate increased with increasing inlet gas velocity ($1.2-2.6U_{mf}$) and the static bed height (z, 0.24-0.68 m) from 2.2 to 23.4 kg/s. However, mean residence time decreased with increasing inlet gas velocity ($1.2-2.6U_{mf}$) and the static bed height (z, 0.24-0.68 m) from 1,438 to 440 s. The solid holdup in the riser was determined by measuring pressure differences according to the riser height. These results showed a similar trend to that of simple exponential decay type except for the top section of the riser. To verify the gas bypassing from top bubbling beds to middle bubbling beds, $CO_2$ gas was injected by tracer gas in constant ratio, and then was measured $CO_2$ concentration in outlet gas by gas chromatography. Gas bypassing occurred below 2.6% which is negligible value.

• Journal of Wetlands Research
• /
• v.16 no.3
• /
• pp.327-336
• /
• 2014

Submerged thin walls are extreme case of submerged rectangular blocks, and could be used for many purposes in rivers or coastal zones, e.g. to tsunami. To understand flow characteristics including flow and pressure fields around a specific submerged thin wall a numerical model was applied which includes computation of hydrodynamic pressure on ${\sigma}$-coordinate. ${\sigma}$-coordinate has strong merits for simulation of subcritical flow over mild-sloped beds. On the other hand ${\sigma}$-coordinate is quite poor to treat sharp structures on the bed. There have been a few trials to incorporate dynamic pressure in ${\sigma}$-coordinate by some researchers. One of the previous approaches includes process of sloving the Poisson equation. However, the above method includes many high-order terms, and requires long cpu for simulation. Another method SOLA was developed by Hirt et al. for computation of dynamic pressure, but it was valid for straight grid system only. Previous SOLA was modified for ${\sigma}$-coordinate for the present purpose and was adopted in a model system, CST3D. Computed flow field shows reasonable behaviour including vorticity is much stronger than the upstream and downstream of the structure. The model was verified to laboratory experiments at a 2DV flume. Time-average flow vectors were measured by using one-dimensional electro-magnetic velocimeter. Computed flow field agrees well with the measured flow field within 10 % error from the speed point of view at 5 profiles. It is thought that the modified SOLA scheme is useful for ${\sigma}$-coordinate system.

• Journal of the Ergonomics Society of Korea
• /
• v.34 no.3
• /
• pp.199-215
• /
• 2015

Objective: The purpose of this study is to find the level of physical relaxation of individual subject by monitoring psychophysiological biofeedback to different types of mattresses. And, the study also aims to find a protocol to make a selection of the best mattress based on the measured information. Background: In Korea, there are an increasing number of people using western style bed. However, they are often fastidious in choosing the right mattress for them. In fact, people use their past experience with their old mattress as well as the spontaneous experience they encounter in a show room to finally decide to buy a bed. Method: Total five mattresses were tested in this study. After measuring the elasticity of the mattresses, they were sorted into five different classes. Physiological and psychological variables including Electromyography (EMG), heart rates (HR), oxygen saturations (SaO2) were used. In addition, the peak body pressure concentration rate was used to find uncomfortably pressured body part. Finally, the personal factors and subjective satisfaction were also examined. A protocol was made to select the best mattress for individual subject. The selection rule for the protocol considered all the variables tested in this study. Results: The result revealing psychological comfort range of 0.68 to 0.95, dermal comfort range of 3.15 to 6.07, back muscle relaxation range of 0.25 to 1.64 and personal habit range of 2.0 to 3.4 was drawn in this study. Also a regression model was developed to predict biofeedback with the minimal use of biofeedback devices. Moreover results from the proposed protocol with the regression equation and subjective satisfaction were compared with each other for validation. Ten out of twenty subjects recorded the same level of relaxation, and eight subjects showed one-level difference while two subjects showed two-levels difference. Conclusion: The psychophysiological variables and suitability selection process used in this study seem to be used for selecting and assessing ergonomic products mechanically or emotionally. Application: This regression model can be applied to the mattress industry to estimate back muscle relaxation using dermal, psychophysiology and personal habit values.

• Clean Technology
• /
• v.20 no.3
• /
• pp.212-217
• /
• 2014

In order to regenerate the sulfidated desulfurization sorbent, oxygen is used as the oxidant agent on the regeneration process. The small amount of oxygen un-reacted in regeneration process is flowed into direct sulfur recovery process. However, the reactivity for $SO_2$ reduction can be deteriorated with the un-reacted oxygen by various reasons. In this study, the deactivation effects of un-reacted oxygen contained in the off-gas of regeneration process flowed into direct sulfur recovery process of hot gas desulfurization system were investigated. Sn-Zr based catalysts were used as the catalyst for $SO_2$ reduction. The contents of $SO_2$ and $O_2$ contained in the regenerator off-gas used as the reactants were fixed to 5.0 vol% and 4.0 vol%, respectively. The catalytic activity tests with a Sn-Zr based catalyst were for $SO_2$ reduction performed at $300-450^{\circ}C$ and 1-20 atm. The un-reacted oxygen oxidized the elemental sulfur produced by $SO_2$ catalytic reduction and the conversion of $SO_2$ was reduced due to the production of $SO_2$. However, the temperature for the oxidation of elemental sulfur increased with increasing pressure in the catalytic reactor. Therefore, it was concluded that the decrease of reactivity at high pressure is occurred by catalytic deactivation, which is the re-oxidation of lattice oxygen vacancy in Sn-Zr based catalyst with the un-reacted oxygen on the catalysis by redox mechanism. Meanwhile the un-reacted oxygen oxidized CO supplied as the reducing agent and the temperature in the catalyst packed bed also increased due to the combustion of CO. It was concluded that the rapidly increasing temperature in the packed bed can induce the catalytic deactivation such as the sintering of active components.