• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.9 no.1
• /
• pp.40-49
• /
• 2004

An ecological study on a sea urchin population, Strongylocentrotus nudus, a key role species in recovery of macroalgal bed, was conducted in Hosan, Samcheok area on the east coast of Korea. Three experimental plots, namely, AMB (artificially-restored macroalgal bed), BG (barren grounds) and NMB (natural macroalgal bed) were established after a pilot survey in June 2002. Distribution and abundance, grazing rates, predation pressure and predator guilds on S. nudus were estimated in three plots bimonthly from Aug. to Dec., 2002. Abundance of S. nudus was lowest, but median test diameter of the urchin was highest (Kruskal-Wallis test, p-value, p<0.001 in Aug. and p=0.003 in Oct.) in NMB In-situ grazing rate of S. nudus estimated by enclosure cage experiment in NMB was about 12 times higher in Aug. (160.0 mg seaweed/g sea urchin/day) than in Oct. (13.8). Predation intensity measured by tethering experiment was higher in NMB. Most of the predators on S. nudus were invertebrates and no fish predators were found. Predator guilds identified by the fish trap experiment using live or dead sea urchins included who]ks Neptunea arthritica, starfish Asterina pectinifera, hermit crabs Pagurus of. samuelis, Paguristes barbatus, brown shawl crabs Atergatis integerrimus and crabs Actaea subglobosa. High predation pressure on S. nudus in natural macroalgal beds was the likely cause of its low density. Elevated sea urchin density and the consequent lasting deforestation of macroalgae in barren grounds demonstrate the importance of predation pressure on sea urchins.

• Journal of computational fluids engineering
• /
• v.12 no.1
• /
• pp.28-34
• /
• 2007

This study evaluates the performance of the packed bed scrubber and proposes the optimization of spray system for improvements of collection efficiency. The packed bed scrubber is used primarily in the semiconductor manufacturing process. The mean diameter of entering solid particles in scrubber is the submicron. The impaction between water droplets and solid particles is an important factor in removing the solid particles. Thus, the coverage area of spray system influences on the collection efficiency. The collection efficiency of a single droplet is calculated through the mathematical model and numerical calculations are performed for coverage area for each nozzle type (Droplet diameters: 500, 319.5, $289.5{\mu}m$) and injected directions (0, 15, $30^{\circ}$). In case of nozzle type 3, the collection efficiency of a single droplet is highest but the collection efficiency of spray system has lowest value because the ratio of flow rate between the gas and water is below 0.1. The results show the coverage area ratio is about 85% in the case of nozzle type 3 and downward sirection $15^{\circ}$. It was shown that a coverage area increase by two times than an existing spray system. In simulation of demister, collection efficiency by demister is predicted about 80% and the pressure drop in demister is below 3.5 Pa.

• Journal of the Korea Furniture Society
• /
• v.25 no.4
• /
• pp.304-318
• /
• 2014

Bed for elderly and disabled, including the United States developed the industry Americas, and European countries, mainly in the production of products has dominated the world market. In large hospitals, and dependent products are sold at high prices. On the other hand, improvement of living standards of our country and to the advancement of residential culture of the demand for luxury products is increasing. The study of elderly Edition mattresses have been developed mainly in Europe to maximize the use of sleep can increase the efficiency of products has been studied. Due to the increase in elderly population Elderly Hospital, which is installed in the elderly silver town Edition requires the dissemination of the mattress in the bedroom several times a day resting and sleeping, eating, etc. Designing a variety of actions are needed. Edition of the elderly in Korea developed the design of bed with bed design and the manufacturer and the Institute for Ergonomics, welfare agencies and to build organic cooperation system under the direction of a professional designer to develop and you need to configure the space and the results of such actions by the distribution of cheap materials, ergonomic mattress for optimal development of behavior analysis to the need to promote the convenience of the user.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.310-313
• /
• 2005

The conical fluidizing system of a binary mixture of Geldart C powders and Geldart A particles was defined as the conical powder-particle fluidized bed. We used a cold conical powder-particle fluidized bed model having a 0.104m-I.D. and 0.6m-high with an apex angle of $10^{\circ}$ for fluidization of a binary powder-particle mixture of 50 $vol\%$ fine carbon black powders (HI-900L, Korea Carbon Black Co.) and coarse alumina particles $(90{\mu}m)$ under different superficial gas velocities (0-0.1 m/s). The differential bed pressure drop increases with increasing gas velocity, and it goes from zero to a maximum value with increasing or decreasing gas velocity. In the conical fluidized beds of fine powders, demarcation velocities of the partial fluidization, full fluidization, partial defluidization was not observed.

• Structural Engineering and Mechanics
• /
• v.38 no.1
• /
• pp.65-79
• /
• 2011

Concrete hydraulic structures such as: Dams, Intake Towers, Piers and dock are usually recognized as" Vital and Special Structures" that must have sufficient safety margin at critical conditions like when earthquake occurred as same as normal servicing time. Hence, to evaluate hydrodynamic pressures generated due to seismic forces and Fluid-Structure Interaction (FSI); introduction to fluid-structure domains and interaction between them are inevitable. For this purpose, first step is exact modeling of water-structure and their interaction conditions. In this paper, the basic equation involved the water-structure-foundation interaction and the effective factors are explained briefly for concrete hydraulic structure types. The finite element modeling of two concrete gravity dams with 5 m, 150 m height, reservoir water and foundation bed rock is idealized and then the effects of fluid domain and bed rock have been investigated on modal characteristic of dams. The analytical results obtained from numerical studies and modal analysis show that the accurate modeling of dam-reservoir-foundation and their interaction considerably affects the modal periods, mode shapes and modal hydrodynamic pressure distribution. The results show that the foundation bed rock modeling increases modal periods about 80%, where reservoir modeling changes modal shapes and increases the period of all modes up to 30%. Reservoir-dam-foundation interaction increases modal period from 30% to 100% for different cases.

• Journal of Advanced Research in Ocean Engineering
• /
• v.2 no.3
• /
• pp.99-111
• /
• 2016

Seabed affected by scouring, sedimentation, and siltation occurrences often cause exposure, which induces risks to existing structures or crude oil or gas pipeline buried subsea. In order to prevent possible risks, more economical structure installation methodology is proposed in this study by predicting and managing the risk. Also, the seabed does not only consist of sandy material, but clayey soil is also widespread, and the effect of undrained shear strength should be considered, and by cyclic environmental load, pore water pressure will occur in the seabed, which reduces shear strength and allows particles to move easily. Based on previous research regarding sedimentation or erosion, the average value of external environmental loads should be applied; for scouring, a 100-year period of environmental conditions should be applied. Also, sedimentation and erosion are mainly categorized by the bed load and suspended load; also, they are calculated as the sum of bed load and suspended load, which can be obtained from the movement of particles caused by sedimentation or erosion.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.1
• /
• pp.83-92
• /
• 2012

Syngas combustion characteristics of mass produced oxygen carrier particle (OCN706-1100) were investigated in a pressurized fluidized bed reactor using simulated syngas and air as reactants for reduction and oxidation, respectively. The oxygen carrier showed high fuel conversion, high $CO_2$ selectivity, and low CO concentration at reduction conditions and no NO emission at oxidation conditions. Moreover, OCN706-1100 particle showed good regeneration ability during successive reduction-oxidation cyclic tests up to the 10th cycle. Fuel conversion and $CO_2$ selectivity decreased and CO emission increased as temperature increased. These results can be explained by trend of calculated equilibrium CO concentration with temperature. However, fuel conversion and $CO_2$ selectivity increased and CO emission decreased as pressure and gas residence time increased.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.5
• /
• pp.355-363
• /
• 2010

High purity hydrogen, 97-99 vol.%, with CO at just ppm levels was obtained in a fixed bed of iron oxide employing the steam-iron cycle operation with reduction at 823K and oxidation in a steam-$N_2$ mixture at 773K TGA experiments indicated that temperature of the reduction step as well as its duration are important for preventing carbon build-up in iron and the intrusion of $CO_2$ into the hydrogen product. At a reduction temperature of 823K, oxide reduction by $H_2$ was considerably faster than reduction by CO. If the length of the reduction step exceeds optimal value, low levels of methane gas appeared in the off-gas. Furthermore, with longer durations of the reduction step and CO levels in the reducing gas greater than 10 vol.%, carbidization of the iron and/or carbon deposition in the bed exhibited the increasing pressure drop over the bed, eventually rendering the reactor inoperable. Reduction using a reducing gas containing 10 vol.% CO and a optimal reduction duration gave constant $H_2$ flow rates and off-gas composition over 10 redox reaction cycles.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.6
• /
• pp.354-361
• /
• 2014

In order to utilize silicon carbide (SiC) as an inner part of fluidized bed reactor (FBR) for manufacturing poly-silicon, we have carried out the thermodynamic calculation on the overall reactions including poly-silicon synthesis and compatibility of SiC with FBR process. The resources of silicon included $SiH_4(MS)$, $SiHCl_3(TCS)$ and $SiCl_4(STC)$ and the thermodynamic yield of the FBR with MS, TCS and STC were compared each other with variable range of temperature, pressure and hydrogen to silicon ratio. The silicon yield of MS, TCS and STC were 100%, 28% and 4%, respectively, throughout the conventional FBR conditions. Silicon carbide having high hardness and strength showed strong resistance to granule collisions during the FBR process using a lab-scale reactor. And it also showed quite good compatibility with the typical FBR processes of MS and TCS resources.

• Nuclear Engineering and Technology
• /
• v.54 no.1
• /
• pp.357-373
• /
• 2022

The high-temperature gas-cooled reactor pebble-bed module project is the first commercial Generation-IV NPP(Nuclear Power Plant) in China. A new joint is used for the vertical support of RPV(Reactor Pressure Vessel). The steel corbel is integrally embedded into the reactor-cabin wall through eight asymmetrically arranged pre-stressed high-strength bolts, achieving the different path transmission of shear force and moment. The vertical monotonic loading test of two specimens is conducted. The results show that the failure mode of the joint is bolt fracture. There is no prominent yield stage in the whole loading process. The stress of bolts is linearly distributed along the height of corbel at initial loading. As the load increases, the height of neutral axis of bolts gradually decreases. The upper and lower edges of the wall opening contact the corbel plate to restrict the rotation of the corbel. During the loading, the pre-stress of some bolts decreases. The increase of the pre-stress strength ratio of bolts has no noticeable effect on the structure stiffness, but it reduces the ultimate bearing capacity of the joint. A simplified calculation model for the elastic stage of the joint is established, and the estimation results are in good agreement with the experimental results.